Yes, it's called a step-up transformer because, if I understand correctly, you want to step up from a 110v power source to run a 220v dryer. Depending on the power (wattage) rating of the dryer, it will probably cost as much as having 220v service installed by an electrician. Furthermore, the 110v circuit must be fused for at least twice the current rating of the dryer, assuming the transformer is 100% efficient. This is because Power = Voltage x Current. If you halve the voltage (220 --> 110), you must double the current in order to maintain the same power rating. For example, if the dryer normally draws 20 amps at 220 volts, it will require at least 40 amps from a 110 volt circuit. This would require a 4000 volt-amp transformer-- a very pricey item indeed. If you opt for such a unit I would certainly consult a certified electrician.
Quick answer, no. The dryer needs 110 volts to run the motor but applying 110 volts to a heating resistance that requires 220 volts you will only receive 1/4 the wattage of the heating element.
No you can't. The dryer is designed to 220, and it won't work. You need a step down transformer rated at the hairdryer wattage.Try Tandy/Radio Shack.
You probably do not wish to do so. Current issues may become a problem for you.
If there is a neutral and ground run to the box, you can convert.
No. It's not even possible.
No.
If you are no longer using the dryer and there are 4-wires, and the dryer was 220 to 240 volts, it can be split into two 110 to 120 Volt circuits.
You need a 110 v to 220 v transformer, which will be inexpensive for supplying an alarm clock. That steps up the 110 v suppy into 220 v for the clock.
220/240 volt (double that in the USA). The critical thing to know is the frequency. In the States it is 60 Hz and in Europe is is 50 Hz (Hertz). This is important because anything with a motor and a power cable will be frequency dependant. Leave any device at home in the US when traveling or moving to Europe as it will not work if the motor is a 110/120 volt motor. For example, Washer Dryer, Refrigerator, Hair Dryer. Thing like a tape player, stereo, CD Player with a wall plug will work fine because inside the 110 unit it converts all electricity to a DC voltage so a typical voltage convert from 220 to 110 will do fine with these devices. On the other hand an item like a Hair Dryer is a 110 volt motor and cannot survive a 50 Hz attack and will burn up. You can by voltage converters in Germany when you get there.
Different plugs are designed so that you can't plug an appliance into the wrong voltage. A dryer is usually 220-240 Volts and your standard outlet is 110-120 Volts. You can't do what you suggest.
True, 220 volt appliances consume less energy than 110 volt ones, but in order to use them in the US, you would need to convert them to 110 voltage. This is a less efficient use of energy. Plus, 220 volt appliances are a more risky because people can get seriously injured if they get shocked from them.
You can't. A 220 volt dryer requires 220 volts in order to operate properly. It will not run on 110 volts.
If you are no longer using the dryer and there are 4-wires, and the dryer was 220 to 240 volts, it can be split into two 110 to 120 Volt circuits.
using step up transformers
You need a 110 v to 220 v transformer, which will be inexpensive for supplying an alarm clock. That steps up the 110 v suppy into 220 v for the clock.
no they dont
LCM of 110 and 220 is 220.
Because a toaster does not pull near the current that a cloths dryer does.
Because a toaster does not pull near the current that a cloths dryer does.
A step down converter will convert the voltage from 220/230 volts to 110 volts. Converters are labeled to display their capabilities, such as "110V to 220V Converter". Read the instruction manual for your Clothes Dryer and sketch the plug. You'll want to know the voltage of the clothes dryer --- it'll likely be 220 V. You need to visit a major appliance dealer and ask to buy a step down converter after discussing the plug type and voltage found in the owner's manual.
110 x 2 = 220
you don't. you just take and use 120 volts from the 220. At least that's what I'd do.
200. That is to say, 220 is 110% of 200.