0
Yes and you will have a spare terminal for future use
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How can you convert 240v to 120v for ac?
Use a step down transformer 240 primary to 120 secondary. You must know what the connected load (amps) is so that you don't overload the transformer. Small transformers are rated in VA.
Why US use 120v and 50HZ?
The US does not use 120 volts at 50 Hertz.
Can you use a 240v 50hz drill in a country that uses 220v 50hz?
There should be no problem at all.
What are the averag volts used in a US Home?
US homes use a 240 volt single phase 'Edison' system. It is a 3-wire (4 with the ground) system. Phase to phase measures 240v, while each phase to neutral measures 120v.
What is cheaper to operate 120v motor or 220v same horsepower?
220 volt will use less energy.
Can I use 120v 10a 1250 w cable for projector 110-240v power in India?
You can use 120v 10a 125w cable projectors 110-240v power in India.
You have 120v photo flash lights - how do you use them with 240v in Oz?
Power adaptors are readily available that plug into Australia's 240v outlets, converting to 120v. Find them in travel, luggage and electronics stores.
Can you use a 30 amp disconnect switch for a 30 kva transformer?
im have a 30 kva transformer 3 phase 480v 80 amp panel 120v what size disconnect should I use
How do you install a 240 volt light switch?
I'm guessing you want to know what a 240v switch is? If you look at a 120v single pole switch, you will see two brass screws on one side. This type of switch is designed to interrupt current flow in one conductor. A 240v switch is really a double pole switch. It has 4 screws and is capable (and required) of interrupting current flow in two conductors simultaneously. This is an NEC requirement. It allows a local means of disconnect instead of having to go back to the breaker, and a multiwire disconnect is required to disconnect all ungrounded (hot) conductors at the same time. That way one 120v leg cannot be shut off while the other is on. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS. If you do this work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.
Can you take a 120V winecooler to Europe and use it with an 240V outlet and an adapter?
NO, unless you get a converter that converts 220 to 110.
How do I connect a single pole 220v switch to a 3 wire 220v motor using 2 hot wires plus 1 ground?
Is it a single pole switch, or a (220)240v switch? A 240v switch is a double pole switch. It has 4 screws and disconnects both hot sources simultaneously.If it's a single pole 120v/277v switch, that just means you can use it on 120v or 277v circuits. If it's not a double pole switch with 4 screws, it's not the right one. Get a 240v double pole switch for this. You can usually find these at home improvement stores.When you state that the motor is a "three wire" make sure that the phasing is correct and you are not trying to connect up a three phase motor.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
120V light fixtures wall mounted you want to convert to 240V for a house overseas?
It will work it you use 240 volt light bulbs.
If you have a 240V 22A welder which has a plug similar but smaller than a dryer plug can you use this in a 120V outlet?
yes ofcourse they both are the same
How do you change a heater from 120 volts 3a to 240 volts 1.5 a?
the simplest solution is by connecting two 120v 3amps heater in series , the same can be used directly on 240v. However the current drawn will still be 3 amps & Not 1.5 amps. The heater output power will be double that of a single heater running on 120v. ( or equvalent to two heaters operating on 120v. supply ) A more expensive method is to use a stepdown transformer which can be powered on 240v & connect the heater on the transformer 120v side. this method will consume approx. 1.5 amps from the 240v supply.
What if your electrician has fitted a 240v socket in your rec room you want to use your 240v deck and amp but find 2 hot 120v wires and 1 earth How can you use your prized stereo?
Not a hard job or complicated but could be hazardous. Hire a professional.
Can you use a 120v cord that will fit a 240v socket the appliance is 240 and the cord is thick?
120v and 240v cords usually have different end configurations and will not plug into the different recepticles. However, if you changed the plug end, and the cord has the proper size rating, then yes, you could use the same cord. But, it also depends on the cord too. Most 120v cords only have three wires in them. One "hot one "neutral" and one "ground" wire. A 240v cord would have FOUR wires, two "hot" wires, one neutral wire, and one ground wire. Therefore, if you changed the voltage from 120v to 240 using a 3 wire cord, you'd not have a ground wire and that could be VERY dangerous. Note that occasionally a 240v device (e.g. some motors) will only need three wires (red,black,green, no neutral) and can be wired with a 120v cord if the cord is rated for 240v.
How can you wire one half of a 20 amp 120 v duplex wall socket to run 240 volts over 2 legs 2 separate 120 v legs?
You can't. I'm not sure exactly what you're trying to do, but the way it is written is not possible. It seems you might want to use half of a duplex receptacle for 120 and half for 240. This would not be code compliant, nor would it make sense. A plug designed for 240v will not even fit into a 120v receptacle. You need a 240 volt receptacle rated for the amperage you will need. Also, an existing 120v receptacle has nothing to do with your 240v receptacle. For a 240 volt receptacle, you'll need to run 2 new 120v lines (in the same cable). The existing 120v circuit cannot be used here, even if you added another 120v circuit, because when a load uses 240v, both 120v circuits supplying the 240v must be controlled by a common disconnect (a 2 pole breaker designed for 240v circuit). My advice would be to show an electrician what you want done. I'm sure they can tell you how to make that happen.
