0
pota ka
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you connect mounting brackets to fender on a 1976 fxe?
The brackets screw to the fender through holes in the fender and to tabs on the fork legs.
What are mounting disks for snowboard bindings?
mounting disks are the disks on the inside of the binding that have holes to screw into the board. they come with the bindings you buy, however replacement disks can be found online. they also control the angle at which you set your foot.
When i bought new front rotors for my 2001 ford windstar the old ones have 3 holes to screw on the new ones dont do these holes need to be there or can you just go without?
You can do without the mounting holes in the replacement rotors.See "Related Questions" below for more
How do you install your safe into a 4 inch thick stud wall?
If it is a safe designed to go in a wall, it should fit between the studs and have mounting holes in the sides. Just screw through the holes into the studs on each side.
How do you remove sun visor 2004 malibu classic?
The sun visor on a 2004 Chevy Malibu Classic is changed by removing the screw covers and taking out the retaining screws. The visor can then be pulled from the mounting holes and removed.
The metal junction boxes that we are installing receptacles in have no ground screw just holes in the back for mounting and knockouts How do you properly ground j boxes?
Make your own ground screw. Use a #8 x 1/2"or #10 x 1/2" sheet metal pan head screw and screw it into one of the holes in the back of the box. In the back of the box you might see a raised portion where the original ground screw came out of, use that hole. Wrap the ground wire around the pan head screw and it will tighten up very nicely and make a good ground.
How do you remove the headlight assembly on a Mazda millenia?
Open hood and remove the hard plastic cover over the headlight and radiator; this will expose most of the mounting screws. Then remove the corner lamp by removing the retaining screw at the top corner of the headlamp; this will expose the remaining mounting screws.
How do you lock the battery down on an Audi A4?
very simple to lock down Audi a4 battery, there is a screw and a base plate lock for the battery, if the battery is bigger or smaller there are 2 holes for you to choose for your screw to be bolted so the battery base plate will be secured. the battery holder is at the bottom part of the battery. To see the 2 holes remove the entire battery cover its so easy to remove the black plastic cover so you can see the 2 holes.
How do you remove the door speakers on a 1998 Chrysler LHS?
This ones pretty easy......The speaker cage the covers the speakers simply pop out with a small screw driver. Put the flat tip of the screwdriver in the crease anywhere around the speaker cover and simply pry it off. Install by fitting the bottom edge back in the mounting holes and pop back in
What is a screw tap?
A self-tapping screw can be used to join two pieces of plastic or metal with simple holes drilled into them. A "normal" screw requires one of the holes to be "tapped" - a spiral has to be cut into one of the holes to accept the screw. Tapping holes is something of a game of skill; the tapping tools use very hard, brittle steel and it's easy to break a tool in the hole.
Is a tap a screw?
A self-tapping screw can be used to join two pieces of plastic or metal with simple holes drilled into them. A "normal" screw requires one of the holes to be "tapped" - a spiral has to be cut into one of the holes to accept the screw. Tapping holes is something of a game of skill; the tapping tools use very hard, brittle steel and it's easy to break a tool in the hole.
How do you pull rear brake hub on 2004 outlander Mitsubishi?
there are two holes on the rear brake hub. Find the correct size bolt and screw them in the holes. Screw one then the other till it pops...then slide it off. there are two holes on the rear brake hub. Find the correct size bolt and screw them in the holes. Screw one then the other till it pops...then slide it off.
