answersLogoWhite

0


Best Answer

You cannot wire a 4 wire dryer plug into a 3 wire outlet for mobile home use - (US NEC) - you must carry all four conductors all the way back to the distribution panel. In a hard wired house configuration, if the dryer is designed to support it, you can replace the pigtail with a three wire pigtail, and connect neutral to ground inside the dryer connection panel. Check your local electrical codes and laws for specific requirements.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

11y ago

First of all, you shouldn't have a 3 pole, 3 wire receptacle unless you have a three-phase dryer with no ground, which I don't even think is commercially available. What you should have is a 2 pole receptacel with ground. If it's in an existing house, you are either on a 120/240V single phase service or a 208V three phase service most likely. To wire the receptacle, you most likely have wha

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

The type of receptacle that you should install is a 14-30R. It is a three pole four wire grounding receptacle. The black wire goes to the Y terminal, the red wire goes to the X terminal, the white wire goes to the W terminal, the ground wire if there is one goes to the G terminal. This type of receptacle requires a four wire cable and plug to connect to your dryer. This configuration conforms to the new electrical code rules for new installations. The connections at the dryer will be, outside of the three terminals connect to the "hot" wires and the center terminal connects to the center terminal. The green wire on the dryer cord connects to the chassis of the dryer. In some cable kits a ground lug is supplied for this connection to the ground.

This answer is:
User Avatar

User Avatar

Wiki User

16y ago

Three wire Dryer was 230 volts , black and red plus ground, four wire will be 230 volts red and black, neutral white and green ground.

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

Plug it into a properly grounded 3-prong outlet. If you don't have one, call an electrician.

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

Two hot legs for power and a ground. usually red and black for power. green is for the ground.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

See view discussion page below.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you wire a 4 wire dryer plug into a 3 wire?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How to Dryer plug wire colours for 4 wire?

Dryer Circuit Wiring and Hookup Check related link below. Lots of pictures.


How do you wire a 220 3 wire breaker to 4 wire dyer?

Buy a 3 wire cord for your dryer.


Is it safe to use an oven that has a dryer plug put on?

It will work if, the dryer plug you are using is the same electrical voltage as the oven. If your oven is electric, it is 220 - 240v, if gas, 110 - 120v. A 220 plug has either 3 or 4 prongs, depending on your appliance being a 3 or 4 wire system. A 4-wire system will have a red wire (110v power), black wire (110v power), white wire (neutral/common), green wire (ground). A 3-wire system will be missing the white or green wire. 110v system (gas oven or dryer) will have a black (power), white (neutral), green (ground). It will work, but be limited. Dryer circuits are 30A, whereas oven circuits are 50A. You cannot just upgrade the dryer wiring to 50A as it is not rated for that and will start a fire. To use the oven properly you need to install a properly rated circuit. Do it right or don't do it at all. Negligence is fatal with electricity.


What is involved in running a 240V dryer line if you have a regular 120V line now?

You will have to install a double pole breaker in the fuse panel and then run new wire (10/3) to the location of the dryer and install the proper plug. You will need a 4 prong plug; the older 3 wire plugs no longer meet code for new work.


Where do you ground the extra wire when plugging a 4 prong wire into a three prong outlet for a dryer at?

It may be a 220 Dryer, and you will need a new outlet installed. There should be no extra wires when connecting the Power cord to the plug


What are the different sizes for plugs on a US dryer?

50 amp 3 and 4-wire.


Does a 4 wire plug for a dryer can be replaced with a 3 wire plug?

The fourth prong is a ground for the body of the dryer. The dryer will work fine with the 3 main ones. Building code requires the four wire plug now, but you can change it and the dryer will work. If you have a 4 plug outlet and a 3 wire cord, you can just change the cord and not use the second ground or connect to the the frame of the dryer.


Can you use 10 3 which is 4 wire to hook up a 3 wire dryer outlet?

If you're using 10/3, then you may as well use a 4-wiredryer receptacle, provided that your dryer is rated for 30 Amps. The NEC in America actually requires this now.


What is the difference between a 4 prong dryer outlet and a 4 prong stove outlet?

The four blade dryer plug brings a separate ground wire from the machine to the electrical grounding system. The three blade dryer plug depended on the neutral wire of the plug to make this connection.


Is it possible to put a 4-prong plug on a dryer that uses a 3-prong plug and how would you do this?

If you are viweing this because you want to change the newer 4-prong plug/outlet to fit an older 3 prong outlet/plug don't do it! The newer plug is safer and the 3 prong plug no longer meets code. See the discussions in other threads. all you need to do is hook the two hot leads on the outer terminals, then the nueatral, white wire on the center terminal and the green ground wire to the ground screw. Be sure to remove the bonding jumper that ties the neutral to the chassis. This is no longer needed as now you have a ground line from the outlet. There should be 3 insulated lugs in the dryer, two hots and a neutral. Connect the red and black wires in your new cord to the hot lugs (red & black are interchangeable), and the white neutral to the neutral lug. Neutral is the center wire on your older 3-wire cord, for reference. Connect the green ground wire directly to the chassis of the sryer using a convienent screw. Use the four prong cord if you can. It is safer because it has the extra ground wire which older cords did not.


4 wire plug red black white bare that has to be changed to a 3 for a welder what wires go where on the 3 wire plug?

See discuss question page below


You are replacing a 3 wire plug to a 4 wire outlet but the stove is set up for a 3 wire and you have a 4 wire plug to switch over but there is no place for the ground wire to go?

The range 4 wire plug kit should have with it a grounding lug that connects to the frame of the stove. If not buy a small #2 lug and bolt it to the frame of the stove. This is the attachment point for the fourth green ground wire from the new range cord assembly.