Unanswered | Answered

Lawn Mowers and Garden Tools

Parent Category: Gardening
If you are confused by the wide variety of tools available to maintain your yard, ask for help here regarding a new purchase or how to fix or improve something you already have.
You can get that info on the Briggs and Stratton website. Just go to: http://www.ereplacementparts.com/briggs-and-stratton-parts-c-16758.html?gclid=CPCZj4vGr58CFZdM5Qodp3bDsA and enter your engine model number.
\nPull the original pullstring out completely, the hole in the wheel should be lined up with the hole in the housing. Use clamp to hold the wheel in place. Measure the pull string and cut the new one the same length. Now wind the wheel a couple of more turns in the way you were pulling the...
\nYour best bet is to go to briggsandstratton.com go to parts then model no. and that should give you the correct part no.
\nMost all will run with a .010 setting.
Try Here: http://www.managemyhome.com/mmh/lis_pdf/OWNM/L0503233.pdf
\nGo to http://jdcp.deere.com go to parts. Type in model no. Go to sectional index click on item 70 cylinder, oil pan etc. It will show you the drain T.
The weights given on oils are arbitrary numbers assigned by the S.A.E. (Society of Automotive Engineers). These numbers correspond to "real" viscosity, as measured by several accepted techniques. These measurements are taken at specific temperatures. Oils that fall into a certain range are...
\nWould need to know model no. to be sure but normally you fish the fuel filter from the tank and pull the fuel line out. Now thread twine through the hole and out the fuel cap hole. Cut the new line to a one inch taper, now tie the twine about the middle of the taper add a little motor oil at the...
Black and Decker
If the mower has a shift knob control for "Start" "Run" and 'Stop', the kill switch will be on the end of the cable that leads to the throttle bracket. If the mower has the safety handle that shuts off the mower when it is not depressed, the kill switch will be at the end of the cable that leads...
Unless your 1450 has a serious internal engine problem (low/no compression, engine won't turn, etc), a no-start condition is due to either no spark or no fuel. You must also have a fully charged battery that will turn the starter and engine with sufficient speed. Check spark at the plug first. No...
\nGo to http://jdpc.deere.com , If it is not on the site you can order it from them.
\n5.5 ounces to a US Gallon which is 128 ounces.\n24 divided into 128 = 5.33
\nNeed more information, what is it? and model no.
a German band
\nYou will have to find where it is leaking. Sometimes from the carburetor if so you will have to remove and clean the carb. and may have to adj. or replace the fuel metering plunger. Other times the hoses between the carb. and the tank have holes which allow leakage. Back in the 90s Stihl had...
Answer . if its dieing under heavy load clean the plug and the air filter and sharpen the blades, make sure your using fresh fuel and mow slower.
Regular unleaded gasoline is usually the recommended fuel.
For the aluminum the intake valve clearance is .005 to .007 inches. exhaust valve clearance is .007 to .009 inches. Cast iron is - intake valve is .007 to .009. inches exhaust valve is .017 to .019 inches
You can find it at this website. You will have to cut and paste the following URL: http://www.managemyhome.com/mmh/lis_pdf/OWNM/L0901280.pdf
oil and gas you can find at the gas station or you can find oil and gas in russia
A flower is the organ of reproduction of the higher plants or Spermaphytes. Non flowering plants such as ferns and mosses reproduce by spores therefore do not require flowers.
Answer . Sharpening the chain correctly not only means you cut well, it is also vitally important for safetly. An improperly sharpened chain can become a safety hazard resulting in kickback etc so it is well worth getting someone who knows what they re doing to show you in practice as its a...
You can try an EZ-Out tool to retract the broken screw or you can take it to a machine shop to have it done. The machine shop will most likely weld a nut to the exposed end of the screw and then just retract it.
Carburetor Adjustment on Pro Saws Info Carburetor adjustment iscritical on chain saws and other two-cycle engines. An adjustmentthat is too rich will cause a saw to smoke, have insufficientpower, and may damage the engine. An adjustment that is too leanwill also produce insufficient power and is...
No. A scythe is a two handed tool for cutting crops, such as wheat, for harvest. Its the thing you normally see the dark hooded caricature of death holding.
\nwhen you are mixing gas for a chain saw. it will tell you 40;1 or 50;1 that is how much 2 stroke oil is in it. you can buy at almost any hardware store little containers of 2 stroke oil that mixes with one gallon of gas. it will say on it what the mix racial of that container will make.
Answer . Basically, the problem is often that, the choke being left "on" continually prevents the engine from starting because there is too much gas for the air being provided. (The choke control reduces the air being provided to burn with gas). On warm days, a two-cycle engine does not need to be...
Answer . the valves or rings are allowing compression blow by to enter the crankcase which causes excess pressure that is brought to the carburetor by the breather tube. your engine is getting tired or you have too much oil in the crankcase.
Engine displacement: 3.5 cu. in. (57 cc).
From the Tecumseh Jiffy Drill website: Ratio for Tecumseh TVO85 (3 hp), AV520 (3 hp), AV600 (3.5 hp), TMO49 (2 hp), TC200 (1.6 hp) and TC300 (2 hp) engines is 40:1. For a 40:1 mixture: Mix 3.2 oz of 2-cycle oil to 1 gallon of gasoline.
One reason would be that the float valve may be sticking in the carburetor and letting gas flow by and into the engine when the mower is not running. The other thing I have seen cause this is one cylinder is not firing and that cylinder lets the gas by the rings and into the crankcase. Most of the...
Try watching this video on replacing chainsaw fuel lines: http://www.youtube.com/watch?v=JrXpU70Hmi0
The mixing ratio using Stihl brand oil is 50:1 or 2.6 oz. oil per gallon of gas. Stilhl oil is recommended though a name brand oil for another air-cooled equipment brand could be substituted. Most are the same ratio.
Normally you will start to hear a loud grumbling sound from underneath the mower when the blades are engaged. With the mower shut off, release the tension from the belt for the blades. Raise the deck so you can grab the blades from the bottom. You should not be able to rock the blades from side to...
For a new one I have seen them for as cheap as $699.00 at some of the big name hardware stores. You can spend thousands if you want to buy a high quality mower from a dealer.
A perfectly honest answer would be : if it has a 2 cycle engine, throw it away and buy only lawn and garden equipment that have 4 cycle engines, chain saws being the exception. All else with 2 cycle engines are throw-aways. You'll spend more than its worth just keeping it going from year to year.
A STIHL 045 av is 75cc and the max recommended bar size for it is 32". However... If you have a 045 av Super then it would be 87cc and the max recommended bar length would be 36". So it depends if you have a SUPER or not. It is easy to tell as it will say SUPER on the top tag right below 045 av.
here is a link that will give you instructions . http://www.ntractorclub.com/forums/manuals/messages/1339.html . hope this is what you are looking for
I know only the simple machines in a lawn mower. Wedge, lever, wheel and axle, and screw.
5 gallons x 128 oz/gallon = 640 oz of gas 640/32 = 20 oz of oil
I recommend you go to your local Walmart Lawn and Garden Dept or automotive parts store or lawn mower shop. They have manuals that will specify the filters applicable to your engine.
Kind of unusual when comparing similar models for the model with more features and thus higher price to have a smaller (or issued-earlier) part number. From what my token research has found, there are two differences. The most important is that on the 88691, there are 2 additional trigger levers;...
Go here: http://www.managemyhome.com/mmh/lis_pdf/OWNM/L0804267.pdf
Before you can find a manual, you need to know the model number. There are several websites that have free manuals - one of the most popular ones is manuals.com. If you can't find one there, you can Google for the manual you want. Your search field will look like this "manual for homelite xxxxxxxxx"...
General rule of thumb is pressure check fuel hose from tank to carburetor if you can do that. There should be no leaks. Also check tank vent. Next would be the carb, then after that make sure the engine is sealed and has no air leaks. If engine has air leaks it will run bad regardless of position....
The L30001 doescross reference to a Fram PH8A That is not saying the filter quality is identical, just that theyare interchangeable.
.010mmType your answer here...
Try going to the related link, below, and click on the "manual" tab. Enter you model number and see if there is a manual for your mower. If there is you can print it or download it for free.
the matierials for a metal hammer are wood(trees) and metal ore(from the ground) The matierials for a rubber mallet are rubber (rubber trees)wood(tree) The matierials for a wooden mallet are wood(trees)