a 400 watt 2 channel amp should do fine. all you need to do is bridge the sub when it is being hooked up
this series of expedition Eddie bauers all come with a powered head unit. This means the amp is built into the radio. However it does have a subwoofer built in the rear passenger side panel by the third row seat with an independent amp for this sub mounted right in front of the sub. If u are trying...
if in usa. go to the library or loginto your library. (public) free, yahda yhada// see chiltions online or in lib. see mitchels only while in lib . then walk to terminal. go to e-sources. got to automotive repair. ahhhhhhhhhhh free and easy.. just use your library car bar...
inside the front passenger side kick-plate (just in front of the fuel reset switch)... three little metric head bolts hold it in.
Disabling the parking brake interlock for in-dash DVD players is against the law in many jurisdictions. The interlock is there as a safety feature and should not be adjusted in any way. The interlock is a safety feature to avoid distracting a driver while driving. However in some older vehicles it...
visit "crutchfield's" website and they can tell you if 1997 is different..
1998 Mitsubishi Eclipse Spyder Convertible .
Factory replacement info: .
In-dash stereo 8-11/16" depth ; Size code E,S,U .
Front speakers Dash: 4" Front Door: 6-3/4" .
Far rear speakers Rear Seat Side Panels: 6x9...
When you open the trunk you should be able to see up underneath the speakers. There should be 2 gold Phillips screws that hold each speaker cover. unscrew these and remove the covers. then remove the four hexagonal screws that hold down each speaker. last, unplugged the grey connectors from each...
Tie wraps can be used to replace a stock radio wiring harness in a1991 Mercury Tracer. The wires can be replaced with other radiowire from an automotive parts store and the tie wrap can hold themtogether.
model no akf4306sw id code hw
Follow the instructions in the manual that came with the CD player. If you have no manual then you will need to find the instructions for the particular model you have.
There are dash kits available to adapt other stereo sizes and also wiring harness adapters. Google for "geo prizm dash kit". Total cost is about $25. I've done it a couple of times, pretty straightforward. Access to the radio is by removing the surround - I think there are a couple of screws at...
hum, around 5.25 inches(circle) usually a 3 screw setup instead of 4(4 screws usually means you have fun ;) )
Car Radio Battery Constant 12v+ Wire: Red Car Radio Accessory Switched 12v+ Wire: The radio harness does not provide a switched power source. Run a wire to the fuse box or steering column for switched power. Car Radio Ground Wire: Black Car Radio Illumination Wire: N/A Car Stereo Dimmer Wire...
== Front: 6-1/2" == .
== Rear: 6" x 9" == .
== Front door: 6-1/2" == .
== Rear deck: 6" x 9" == .
You don't need to cut the wires at all, I just got mine installed in 5 minutes with the adapter speaker plug, I got them from Amazon for 16 bucks but you save a lot of time and you don't mess the wire...
Yes, wire each sub in parallel to get a 2 Ohm load p/channel. The amp is rated to be stable @ 2 Ohms/channel, and will make 300w RMS on each channel. Keep in mind PUNCH amps are under-rated, so you will likely get 350-375w/channel, provided your alternator is strong enough to provide a constant 13.8...
The white and blue wire. Its the constant power from your battery so if your putting in an after market CD player you might have to hook the red wire from the deck onto the white/blue wire also so it has a memory for radio stations and tuning
With the Right in-dash kit like what u would find in walmart u can put any CD player in any car and if u don't want to cut wires get the wire harness for ur application
The JBL speakers are included with an optional sound system and not all 2000 solara's have them.
If your vehicle has the JBL speakers it will have a small JBL emblem on the radio faceplate.
Also if you have the JBL speakers you cannot replace the stock faceplate with an aftermarket one...
NO, COMPONENTS ARE JUST THAT, SEPARATE COMPONENTS, IE SEPARATE WOOFERS AND TWEETERS WHICH YOU MOUNT INDEPENDANTLY, THESE SPEAKERS ARE KNOWN AS THREE WAYS, 3 SPEAKERS IN ONE UNIT BASICALLY.
About 1A To 1.5A (or 2A) i tested it one month ago.
Use the SRC button to put the radio into STANDBY mode. Screen should show STANDBY. .
Press and hold Menu button for two seconds. .
Use the joystick control to scroll up or down until you see DEMO ON. .
Press the joystick in for two or three seconds. Screen should show DEMO OFF. .
Compare VU meter to peak meter PPM..
Scroll down to related links and look at "VU meter - Wikipedia" and "Peak meter - Wikipedia".
The future is ready, already
The speaker impedance does not match the amplifier's specified speaker impedance.
size depends on the watts. .-Shocker
Yes a remote wire is necessary. You must wire the remote wire from the amp to and ignition source of power (a component which turns on when the ignition in the car is engaged.) i.e. the radio. The remote wire signals for the amp to power on.
Remove the panel over the fuse box, just pull it out, the same for the identical panel on the P/S. Remove the 2 bolts in a recessed hole in the glove compartment, 1 bolt on either end of the dash where the 2 panels are that you previously removed. Remove a Phillips screw from the defroster vent and...
memory wire color for kenwood kdc138
First, remove the front engine cover (the part with the glove box in it) by removing the two screw on the upper sides and the two horizontal nuts on the very bottom front on both sides. Then remove the dash face cover by removing the screw on the top left hand side by the drivers door hinges, and...
Depends on make an model an year an if its in the back or in the door panel if you already have access to the speaker turn up the radio an put one wire on one side an the other on the other side an see if it turns on if its wrong nothin will happen then flip the wires
You will want to first check whether you own a Miata with a Bose Sound System or not (there should be a Bose logo on the speaker grills). If you do not own a Bose System using an aftermarket radio adapter kit from Metra will help you wire it in very easily. Therefore, the only difficulty is...
Not to be rude but that is a BIG no!! You would think that it would be the easiest way but its not. With most pioneer CD receivers they come with a quick disconnect wiring harness. Not only that the colors on the wires are different. Granted they still have the same red, and black wires which are...
The first thing to check is the fuses. There should be one in the fuse box, and there is likely an in-line fuse to be checked on the power wire near the stereo itself, behind it.
it depends on the car or the radio or they way it was fix.
serial # 9Z154277A (on top of stereo) your code is 6563
Your in luck my friend i have the same year of car all i used was a inline converter that's hooked up to the back 6x9 speakers
To get all the audio voltage from a source to a target without loss you need voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is at least ten times higher then the output impedance. An input impedance is called also a load impedance...
There are three things to a great stereo system. First, you need a good sound source. CDs played through a dedicated CD player are about as good as you will find and are normally a better quality than MP3 format music. Next, a good quality amplifier is important. There are many cheap amplifiers...
RCA stands for the Radio Corp. of America. The jack was their invention and has been around for a long time. A din plug was invented in Germany and it stands for Deutches Institut fur Normung. The plug is widely used now but does not hold a patent.
http://www.geocities.com/svxdc/WRX-pinout.htm Geocities is dead. Pin-outs are now on new site. Also, there's a different table for Foresters: http://ae64.com/Forester-pinout.htm
yes you can just run them straight from the amp to the sub an it will work
because you have the constant power and the ignition power crossed
I bought a stereo to install myself. The pro-installer/salesman told me of this wire. You know how the stereo display light goes brihgt to dim when you turn on your head lights? This is a low voltage input to the stereo. Is this what you are dealing with?
Typically the bigger the sub the harder it hits. It also depends on power handleing and the brand. Personally I think a 15" sub is the best size because it definitely is louder than 2 10"s and possibly the same as 2 12's(im sure people will argue this) plus it will probably fit anywhere a single...
Some of them (newer ones) have a setting in its menu called "Clock Adjust"... Older ones, pressing the clock button for 5 seconds, then starts to flash the time, and you adjust it.
Check fuses, but there is a possibility that the CD and radio have been destroyed.
First remove the trim from around the handle. Use a flat blade screwdriver for this. The pop the small plastic peice from behind the grab handle. There are two Torx screws there. Then you will need to POP the plastic retainers loose that hold the panel to the door itself. They make a...
connect the both positive terminals together and both negative terminals together. use a multimeter to check any positive and negative terminals
for this you'll need a special cable so that it actually stays connected(and stowed in the trunk). I replaced mine two years ago using the normal method and all my gauges went screwy until I got the cable and had both attached. I guess there is some type of controller, or receiver unit in the...
turn the key on but have the CD player off. push and hold the audio button until the clock setting displays
Your CD player is located in the console, directly below the stereo. The sliding door should be close to the floor board on the passenger side of the center console.
See if unhooking the battery terminals for a few minutes doesn't reset the system and allow access to the radio.
It depends on the quality of the amp...and the speakers..no one can really answer that question with the information you gave. .
Don't forget that you can permanently damage your hearing by playing music too loud.
I know that it is 120W "RMS" (which I've been told that is an erroneous term) but there is another kind of watt. I don't know how it is called. The kind that stereos use in stores.
Hello. Bypassing a parking brake on a Pioneer radio requires aninterface. You can not just ground the parking brake wire. You canbuy them on Ebay or Amazon.
Local stores say 5 1/4, online configurations say 6 1/2..
These are shallow depth, around 2 inches max..
What make and model sounds the best?.
Not some cheap $80 a pair setup.
If your talking about the door speakers then you will have to remove the door panels to get to the speakers.
well if its a 2 channel then 1 pair of subs like if it has only one red and one white connecters then only one pair of subs then if it has 2 of each then 2 pairs of subs that's called a 4 channel amp seacrh in Google 4 channel amp and 2 channel amp you'll see what am talking about see look http:/...
wire color stripe color.
dk blue = mute.
black/lt.green = ground.
lt.blue/red = panel illumination.
yellow/black = radio power feed.
black = vehicle chasiss ground.
lt.green/purple = memory feed.
wire color stripe color.
orange/red =rt rear spk.
you have to drill out the rivets then the speaker just pops out
A 2 channel 900w per channel amp or less will run it, or a 1800w one channel amp etc.. Keep in mind the ohms need to match up too
shoud be 6.75 in door 6.5 will work and 4x6 in rear
Would be compared to 1200 watt amp