Unanswered | Answered

Chevy Silverado

Parent Category: Chevy Trucks and SUVs
Also known as GMC Sierra and the Denali in Mexico, Chevy Silverado is General Motor’s latest model of full-size pickup truck which received the 2007 Truck of the Year award from Motor Trend magazine.
Are you trying to get the footprint of bigfoot?!?
your answer on this one is 3.7 quarts or 3.5 litres not sure if that's including the filter not that that makes too much difference. i found this on http://www.samarins.com/reviews/corolla.HTML. specs are based on a 1ZZ-FE 1.8L
There are many different features of a 2002 Chevrolet Silverado. Some of these features include a V-6 engine, chrome bumpers, an engine hour meter, and front and rear ventilated disc brakes.
The 2005 Chevrolet Silverado offered at least two packages. The first reduced cost by using a 2 wheel drive as opposed to 4 wheel drive. The second offered for the first time a sun roof.
Answer . It doesn't have a bolt. Just put the puller's collar around the pulley hub, and with a bit of effort, the pulley comes off. A lot of mechanics use an air impact to drive bolt for the puller..
Answer . Go by the SAE weight/viscosity stated in the owner's manual, or hood, or sometimes on the oil cap itself. Use Valvoline oil..
you can buy just the glass mirror part at most auto part stores its held on with silicon
The woman's name is not released. Many commercial actors/actressesare not known well enough for their names to be made known.
Probably the weep hole. It indicates that the impellar shaft seal is worn and needs replaced. Unfortunately not all pumps can be rebuilt and some must be replaced,check with the manufacturer to see if a rebuild kit is availabe as the entire pump on some models can be quite expensive. Shop around for...
take the driveshaft out and take it to a driveline repair shop and they will have it repaired in a day then BE VERY CAREFUL they will have the caps taped on so they dont fall off because inside of the caps are small pins that are lined inside of them only being held in place with grease.when you are...
If you need to set the timing on a 1998 ZX2, one of two things have gone wrong, 1; your computer is not correctly controling the the timing and needs to be replaced ( this is a simple operation, as it is located under the radio of the the vehicle, and is realativly easily done), 2; your timing belt...
You may want to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
Assuming that is throttle body fuel injection, 41 to 47 psi.
Answer . See http://www.benzworld.org/forums/w163-m-class/1166641-ets-bas-warning-light-fix.html
The Silverado Resort and Spa is located in Napa, California. To be exact, it is located on Atlas Peaks Rd. The Spa is across the street from the Resort.
Should have 11. Upper and lower ball joints (4), outer tie rod ends(2), inner tie rods ends (2), idler arm (2) and pitman arm (1).
Owners of Chevy Silverado's choose to lower their trucks for aesthetic reasons. There are no real performance advantages to a lowered truck, and in fact, if a truck is lowered too much, it can cause problems when driving over uneven terrain.
If it's running like it's supposed to, there's no need to replaceit. I have an 87 Silverado, and it's never had the injectorsreplaced.
You can buy a used 2004 Chevrolet Silverado different places. You can go to a Chevy dealer to see if they have any that were traded in, you can check other used or new car lots. You might see one for sale in the newspaper, perhaps on craigslist, or at a car auction.
There are various websites who sell parts for the 1985 Chevy Silverado. The most popular include JC Whitney, Raybuck Autoparts and Auto Parts Warehouse.
English translation: "I have a 1997 Chevrolet Silverado. Keeps losing the battery charge, I've checked the alternator. Can someone help me?"
The air intake temperature sensor on a 2003 Vibe is located in thehose that connects to the air cleaner. It is near the end of thepart of the hose that connects the air cleaner to the carburetor.
you should have marked the distriputer and the actual intake before removal, if not you will need to go at it the old fashion way like i did , get the number 1 piston to tdc on the combustion stroke and point the distriputar with the number one tower facing the number one piston and leave lose...
Answer . First take off the horn pad , then you will see a snap ring on top of the nut remove it then you can use a socket to remove the nut , also there is a lead weight that will come off when you remove nut . You can get a steering wheel remover , but i just rocked the wheel back and forth...
Answer . It depends on the kind of vehicle. If it's a ford, you might just need a solenoid. Some fords have an external solenoid, mounted on the drivers side wheel well.\n. \nSome vehicles have a solenoid integral to the starter. In those you might need a starter.
Answer . \nnot enough information what type of vehicle does it have a idiot light or gauge
I had this happen on my 2003 Sequoia while under warranty. I was a defective gauge and required replacement. Type your answer here...
Bar from the handle to the latch is broken or disconnected.
There are two fuse boxes. One is located on end of dash on drivers side, you need to open drivers door to see it. The other one is located under hood on drivers side, to the front and a little to the left of the master brake cyclinder...
You can sell a Silverado Bumper online from websites such as eBay auctions. Alternatively, you can also sell this item on local classifieds such as Craigslist.
it will be on the exhaust manifold towards the back by the fire wall or just below the doenut gasket. it will be the first 02 sensor in the exhaust system going from engine to the tail pipe. good luck NEUTZ
One could purchase a 1988 Chevy possibly at a local used car dealership and online. Among the websites are Cars for Sale, Amazon, eBay, Craigslist, Autotraders, and Auto Trader Classics.
If you drive the vehicle nicely at a very reasonable speed you should be able to go approximately 525 miles in a short cab and 675 miles in a long cab.
4wd will slip a little when turning from outside wheel travel further then inside wheel. If they are locking up I would say different gear ratio front to rear or tire size not matched on all four corners.
All u have to do is get the VIN or a key number and take that to a Ford dealer.
Answer . \nhave you checked the fuel gauge itself to make sure it is working
Answer . This is usually a sign of a timing error... depending on make/model of your car you may need diagnostics of a timing light and a manual... I guess it could also be dirty air-filter or mixture incorrect..... I would suggest you check the timing though!
Answer . You can either replace the switch or temporarily, jump across the connections. This will move the window to the up position.. Better answer.... The switch needs to be plugged in, in order to jump the connections. Remove the plate that cover the inside handle, unplug the power door lock....
Electronic controls are in the ECU and on the transmission. Mechanical controls are on the steering column and attached to the transmission via a cable in a sheath.
Answer . \nCould be a bad TPS> (throttle position sensor). Answer . clogged fuel filter, amongst about 583 other things--- Good luck
Answer . Usually driverside.com is the best place to find this type of information, but the car is too old to get an estimate on without more information.. It depends on where you live, condition of the vehicle, and installed equipment. www.nada.com will give you the answer.
YEs it should!! the tech is trained to accomplish all that > when a car comes in they cannot let the car leave if there is still something wrong like the radiator not being flushed after changing the manifold gasket, your tech was probably hoping that you would pay the extra cost.
Due to unforseen consequences, you should really let a professional do your brakes. If you still insist, then, You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
\n. \n Answer \n. \n. \nby taking off the old one first\n. \nthe alarm will be bolted underneath near the engine somewhere\nall u need to do is find it\nit will look like a little square box with couple wires\ndisconeect wires unbolt\nreplace with new one\nthat easy!
Take the lock to a locksmith, or take the VIN to the dealer and have him/her make you a key. Neither method is cheap, of course. You will have to go to the dealership that made the car. If it is an old car they should still beable to get an original key for you. I suggest you make a copy of extra...
Answer . Wheel alignment problems\n. \nTires mismatched, worn unevenly or damaged\n. \nOne brake dragging\n. \nBad bearings on one side\n. \nVehicle frame bent
Welcome to the life of anyone who owns a GM 90 degree V engine.Those and intake manifold gaskets are two recurring problems. First, ask yourself - are you mechanically inclined enough to dothis? I mean, you asking this question on here kind of makes mewonder. Not trying to be patronizing here, I...
Answer . Other than measuring it, any Auto Parts store has this information.. The maximum wear diameter of the drum is cast onto the outside of the drum.
Due to unforseen consequences, you should really let a professional do your brakes. If you still insist, then, You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
There is as small hole somewhere in the rear bumper. The vehicle's included tire tool kit should have the device(s) necessary to fit in that hole and should then be twisted to crank the tire down.
Answer . \nI would suspect plug wires connected incorrectly. Go here and pick the year and look at the photo closely to see if you have them correct. \nhttp://autorepair.about.com/od/enginefiringorders1/
Make sure that the wiring harness is properly grounded. Baring that, there is probably a short in the wiring somewhere. A short means the two wires used in trailer lighting are touching someplace.
Answer . AS VIEWED FROM MATING END OF CONNECTOR\n. \nA B C D E F G H I J\n. \nK L M N\n. \nA Left Front Spkr (-) Light Gray\n. \nB Left Front Spkr (+) Tan\n. \nC Right Front Spkr (-) Light Green\n. \nD Right Front Spkr (+) Dark Green\n. \nE Ground Wire Black\n. \nF Not Used\n. \nG Headlight...
Need to know which year, and whether you have the quad or extendedcab. In the quad cab and extended cab models, it's usually underthe rear seat. For the standard cab, it depends on what year youhave. On my 87, it's actually in the engine compartment. On morerecent models, it'll probably be under the...
I hope I make myself clear... . If you mean the ones in the door, its easy. First unscrew the 2 bolts from the hole where you grab the door (please forgive my english), then the second one is where the lock is. After that you have to pull the inner cover of door (with care, of course), because its...
The 2014 Chevy Silverado 3500HD runs on Diesel fuel and is powered by Duramax Diesel. You can get more information about this vehicle online at the Chevrolet website.
Chevrolet Silverado is famous for being one of the most sturdy pickup trucks in the business. It is widely used by people all over the world and are usually relatively cheap.
Turn key on and press fuel peddle 3 times fast see if that does it
Answer . \nIt is behind the passenger side glovebox.
It's not. Call a GM dealership, tell them your VIN #, and they can tell you the gear. ratio it came with from factory.
The Chevrolet Silverado 1500 SS is a pickup truck. Specifically, it is a really big pickup truck. Chevrolet first started manufacturing the Silverado back in 1998.
You can find images and pictures of a Chevrolet Silverado 1500HD by visiting Google Images online and typing "Chevrolet Silverado 1500HD" into the search box.
AFE pro dry air filter is the one used in the 2007 Chevrolet Silverado. This air filter cost between 55-72.00 dollars. Some of the filters feature and increase in air being pushed into the the car.
You should look for any hard shifting, loss of power, and abnormal strain. This can be found by test driving the car and inspecting the engine and transmission.
The Chevrolet Silverado truck originally hit the market in 1998. The first generation included the 1999 model and ran until 2007. The second generation began in 2007 and is still in production today.
The engine of a Chevy Silverado has the potential to last almost indefinitely with proper maintenance like tune ups, oil changes, and replacing worn or broken parts and gaskets every few years.
go to your local feed mill and weigh it! my quess 5600# dan
If it is a serpentine belt you replace the tensioner pulley
Z71 is the "off-road" suspension package. It adds jounce bumpers, larger shocks, and skid plates.
It depends on many factors. Up till the mid 90's they generally had less than 200hp. In earlier than 1995 the 5.0 silverado had 175hp In 1996-1999 it got a boost to to 230hp and was labeled a Vortech engine. The early mustang standard 5.0 had around 225hp depending on the year. The new mustang...
Answer . To convert foot pounds to inch pounds, multiply by 12. 10 ft/lbs is 120 in/lbs. . Answer . To convert foot pounds to inch pounds, multiply by 12. 10 ft/lbs is 120 in/lbs.
Center rear of oil pan, It is a cast alumium pan the oil filter will be just left and up from it. 15mm bolt.
Technically 2, front and rear. But in reality the front and rearaxles are in two sections each, right and left, each run from theplanetary gear in the center.
remove black plastic panel on inside behind mirror. remove switch panel by pushing forward then lifting up. disconnect wiring. remove panel covering door handle[one screw]. remove screw behind this panel. remove screw at top of arm rest from underneath rest. remove screw from underneath back corner...
I do believe all 88 to 98 silverados
\n. \n Answer \n. \n. \nshould be in left side of trunk behind the carpeting in the fender well
yes. if they are original.
Answer . \nkbb.com prolly around 1500
If calipers were also replaced there has to be something else preventing the pads from backing off. If it was only one side I'd suspect the hose, if it's both I'd have a look at the master cylinder.
Driver side firewall it has a cover on it and should be full of fluid
There is no real break-in period with the new engines. They all use an alloy of aluminum and silicon (as in quartz) to give ultimate wear resistance to piston rings and all give about 250,000 miles of service. The American made motors give as good if not better performance than that of the foreign...
Obviously whoever designed the transmission for it was educated beyond their intelligence and got the bright idea to either save a little space or a couple of dollars to build it and left it off. Now that being said there is a place to check the level and add more if it needs it but getting to it is...
Answer . \nMakes no differance. The pressure of gas is very low and is not affected by the shape of the fitting or the way it goes on.. Answer . \nthe union should be furthest away from the unit.
Heater core its air bubbles in the lines when the motor starts the water pump starts circulating Check your radiator coolant level NEW ANSWER: Yes he is right. But you need to check the heater hose quick disconnect that is screwed into either the front left side of the intake or rear left side of...
Heater core has air in it and or plugging up.
Dont worry about rest of alarm if you are having starter issues, just find the Purple wire (on GM veh. Other manufacturers are different colors) in the factory harness at the steering column and put it back together. This is the starter wire and is usually cut in two so a starter kill relay can be...
if its the clicking I'm thinking of its the actuator for the vent door. try shutting off everything off in the heater/a/c system for a couple of minutes and then turn it back on. that usually stops it for me.
Just about anything......From the small 262 4.3 liter V-6 all the way up to a 454 big block V-8. Ask your local mechanic or any gear head.
if the car just clicks, check the clutch switch if manual or the park switch if automatic. if it rotates slowly, check the battery and the cables. the ground and the hot going to the starter. if it rotates and wont fire, check the coil packs, plugs, and plug wires. if it firesbut wont start, could...
EBay can get you a factory service manual. Best bet for a full repair guide tuned to your vehicle exactly. The Haynes and Chilton's aren't keyed specifically to your vehicle, but are generally cheaper, and can be located at your local Autozone/Advanced Auto.
I have a 94 mustang and the switch is in the trunk, left side by the brake light. You can see it as soon as you open the trunk and look on the left side behind the brake lights. Maybe yours is located there too. Good luck..
not sure but if u know someone that works at a car/auto body shop u can ask them to type in their computer the name and year of the part u need to find where it can be ordered well at least in my city. If your talking about the Ignition Control Module!It is under your coil packs.( what your coils...