Unanswered | Answered

Chevy Venture

Parent Category: Chevy Vans
The Chevrolet Venture was a minivan manufactured by General Motors from August 1996 to June 2005. The car replaced the Chevrolet Lumina APV in 1997 and was sold as the Opel Sintra/Vauxhall in Europe.
2 bolts recline it back and tip it up and slide it out. The only problem is the bolts are big torx heads.
Answer . \n . With Fuel Injection:\n . Inside the fuel tank\n . \n . Without Fuel Injection – Carbureted \n . Inside the fuel tank (some models)\n . (Some models) On the passengers side front of the motor, near the bottom (you must raise the van and access it from below). It should have two...
The correct tire pressure for a 2000 Chevy Venture is 32 psi frontand rear. This is for the original tire sizes of P215/70R15 front,and P225/60R16 rear.
if it is just a head gasket, it could be $400 or more depending on if it is the "front" head or the "rear" one. The rear head usually requires you to remove the engine. Most likely the head is also warped, etc (especially if overheated) and will need to be machined on a lathe or head replaced ---...
if you don't have a proper scan tool to reset it, then the only other way is to disconnect the battery for 5 minutes. warning : the radio and clock, etc will reset also & the radio security lock could activate (radio would then not work until reset)
Removal of serpentine belt: Directly below the alternator you will see a small idler pully, below that a tension pulley on a long trianglular arm. A 3/8 ratchet will fit right into the square hole near the bottm of that arm, pull up and towards you and the belt will go slack, just pop it off the...
Answer . \nThe chime has no relevance to the fuel pump.\n. \nThe pump for that year should be in the tank IF it was originally any form of Fuel Injection; CFI / TPI / MPI – if it was ‘carbureted’ then the pump was on the old motor.\n. \nIn retrofits of this nature it is common for whoever that...
Answer 1 Sounds to me like you have somthing like a rag sloshing around in the gas tank. This could occastonally cover and block the fuel intake. Answer 2 I have to respectfully disagree. A blockage at the fuel tank intake would not have an almost instant effect on the fuel in the carburetor...
There is a leak in the rear lines running to the back.
Answer . \nFor a 93 or 94 pry off the black triangular piece of plastic inside the door. \n. \nThe mounting screws are under it.
standard capacity is 24 gallons
\n. \n Answer \n. \nThe best place to go is www.mygmlink.com, where you can register your van and then get a PDF copy of the owner's manual.\n. \nTake Care\n. \nalso check out this site\nhttp://www.ownersmanualsource.com/chevrolet/chevrolet-venture-owners-manuals/
Either the wiper arm(s) moved on the spindle or the linkage moved or bent. See sources and related links below for wiper blade information.
There are no u-joints on the venture van. It has CV joints that are sealed with rubber boots and cannot be serviced. They can only be removed and rebuilt or replaced, etc
the rear wiper uses the same water tank as the front wiper and it is located in the engine area on the passenger side. There are 2 pumps in the tank -- one for the front, one for the back
It does not have a distributor, modern engines have coil packs controlled by a computer. Follow the spark plug wires to the common location
Answer . get it checked, because if the ligt blinks, something is wrong.
2 pounds to 4 pounds, depending if it is completely empty or not and if the van has rear air conditioning or not
TAke it to the dealer as something is wrong for it to come on. The air bag won't work with the light on most of the time.
Answer . Check the resistor pack on the evaporator case under the hood.
there can be several reasons, however it is usually due to overheating and/or sudden cooling --- such as overheating the engine and then pouring cold water into the radiator, etc. Occasionally, the engine manufacturer may have a flaw in the head casting or too thin metal, etc that will cause it to...
The 1997 version has the 4T60e transmission
there are 2 cabin air filters located behind the glove box and there is an access door inside the glove box to get to them
There is a drain petcock located in the bottom tank of the radiator. Depending on which Chevy you have it may be located directly on the bottom with a protective sleeve around it or on the side of the tank facing the engine compartment.
A good mechanic with a vehicle lift and transmission hoist, etc that has done it a few times will take about 8 hours. The home mechanic, all weekend. The engine and transmission come out the bottom together in a cradle/frame, then you can separate them. The van has to be lifted high enough (3+ feet)...
Located under the driver side rear, just forward of the rear bumper. A couple of bolts, an electrical connector and 2 air lines.
using a block of wood to protect the oil pan, lift the engine with a jack to take the load off the mounts while changing them
If the check engine light is flashing off and on when the engine is running that means an engine cylinder(s) misfire has been detected . You need to have the vehicle scanned for any trouble codes to help diagnose and then repair the problem
the 1998 venture fuses are located on the right side of the dash board when you open the passenger door.
I'd suggest pulling the new plugs and checking the gapping. Replacing properly gapped plugs with improperly gapped ones can cause a loss of power. And if you replaced them yourself with "pre-gapped" plugs, check them anyway. A lot of the "pre-gapped" ones are incorrect. If you are a do-it-yourselfer...
I have the same problem in a 1999 K2500 with the LT package. Any ideas?
Answer . Refrigerant level low or cooling fan not working. worst case would be that the compressor no longer can build enough pressure and needs to be replaced
the 1999 venture has the PK3 system for security, so you have to go to a GM dealer or a automotive locksmith that has the proper box to reset it or make a new master key for it.
3.4liter engine takes ph3387a FRAM
You did not specify which O2 sensor it is. Is it sensor 1 bank 1, sensor 2 bank 2, sensor 2 bank 1, or sensor 1 bank 2. There are four O2 sensors on a mazda 626
Passenger side behind the glove box. Remove the glove box to get to it. Change your air conditioning air filters while you are in there.
18.5 gallons for the 2nd generation
Hi, The Cabin Air Filters (there are two) are located behind a couple of panels at the back of the glove box. The first panel snaps out, and then you will find a door behind that panel that opens up. The first filter should slide right out, but the second one has t be moved over to the door...
Yes, those GM 3400 motors are the same. The transmissions are different -- 4L60e versus a 4L65e
try this video with the instructions located below the videio . http://www.ehow.com/video_4804005_replace-pressure-regulator-gm-engine.html
If it is motor oil in the anti freeze, then it is either a cracked head, cracked engine block, or a head gasket blown. If it is transmission fluid in your antifreeze, then the radiator is leaking from the transmission cooler ----- although usually that would cause antifreeze to be in your...
Yes you can block it off. Go to www.streetrodguys.com they have rear block kits for most everything. Highly reccomended
The blue book price for a used Chevy Venture depends upon its year of manufacture, the length of its wheelbase, it accumulated mileage and many other factors. For example, a used 2004 Chevy Venture LS with 43,000 miles on it has a blue book suggested retail price of $9,995. A 2001 LS with 65,000...
You can find it on Honda or ford dealerships and you will look it up and ventures will be on sale and you can find price range and nice to used prices on your Chevrolet ventures.
The price of the used Chevrolet Venture will depend on the year of the car, mileage, and general wear and tear of the vehicle. You are better off deciding how much you can afford and finding a car to match that.
There are 2 screws on the inside that get removed and pull the latch down.
Answer . They are not designed to work at normal operating temperature. They are designed to work when A/C or defroster is on and/or engine coolant temperature exceeds 235 degrees
red fluid is transmission fluid and could be leaking from several locations around the transmission. Check the cooler lines where they go into the radiator, the seals where the axles go into the transmission, but most likely is a leaking pan gasket, etc. The only good way to find it is to look under...
The 'Low Break Fluid' light in the dash comes on.
Radiator replacement in the Chevy Venture van requires removing the 6 attaching posts and the hoses that allow for circulation. The gaskets at the hose connection points should also be replaced. Replacement time is 60 to 90 minutes.
mine did the same thing i just added some coolant to it and it fixed it and havent had any more problems watch your hands though its the line running between the fan and the motor ... i walked around with burnt hands for a week
the sensor is located inside at the base of the windshield, in front of the defroster vent. It looks like a small hole. The newer ventures have 2 holes (one is for the security blinking light) If you are trying to disable the daytime running lights and automatic headlights, then remove the fuse...
The starter relay is located on the radiator support on the battery side of the van. I have included a link (see below) that shows this location. You will find a drawing at the very bottom of that page.
You'll see two lines coming in and out of the compressor. One will be larger than the other. The compressor splits the low pressure side from the high pressure side. The smaller line will be at the compressor outlet, and that's where the high side of the system begins. From the compressor, the line...
the only engine that comes in the venture vans is the 3400 (3.4L) GM V6
\nRemove the 3 screws and pull the ring down -really hard-
Disconnect the negative battery cable. . Drain the cooling system into a clean container for reuse. . Remove the air cleaner and duct assembly. . Remove the wiper linkage. . Remove the heater hoses from the heater core. . Remove the lower center console. . Remove both instrument panel insulators. ....
Mounted on top and inside the fuel tank.
The 1988 pajero is set to idle fast at start up until the engine has warmed up. Then the idle should drop within 800 RPM range.
The 2002 Chevrolet Venture takes 24" wiper blades on both sides front and a 16" rear wiper. See sources and related links below for more information. Since there are over 22 different wiper arm attachments, do not buy wipers just by length only - be sure to lookup exact wiper blade part numbers by...
I went to a Chevy dealer and they printed me a copy for my 97' delta 88. I'm sure they could do it for you.
Hi, There is no radiator fan "sensor" for this vehicle. The fans are controlled by the Powertrain Control Module (PCM). The basic concept is that the PCM uses a temperature sensor to measure the engine coolant and will turn the fans on and off at the appropriate time and speed. There are...
This is a job that requires a special tool and various hand and power tools. If you have access to a spring compressor as well as normal automotive tools it isn't all that hard. start by raising the hood, removing the wiper arms, plastic cowl, wiper motor plug, and wiper motor/ cowl assembly. next...
Mounted on top and inside the fuel tank.
An agreement, possessing the legal characteristics of a partnership, between two or more parties who join forces to achieve some specific, short-term goal, such as the design and construction of a project.
Hi, The Body Control Module (BCM) is located under the dash, on the passenger side of the van. You will have to remove the lower dash panel to get to it. I have included a link below that shows its location, and there are various photographs. I know this is for a 2001 model, but the 1999 model...
Hi, The fuel pump is located inside the fuel tank. To access it, you have to drain and remove the fuel tank because none of the vans in this line (that I know of) have an access door. Sorry about that. Good Luck, Greg
use an L key to remove the screws and the rest is easy. i had this problem also until i saw a mechanic do it.
if its the same as the 2000 look for your oil drain plug, then it should be twards the back of that up a little bit and its a cylinder shape thing with two diffrent size cables coming off of it. if your havin troubles finding it it mounts to the transmission.
\n. \n Answer \n. \nSpecifics may depend on the make and model. Typically, with the engine off and the vehicle on level ground you just pull the dipstick, wipe it off, slide it back in and look at the oil that is now on the dipstick. There is usually some kind of marking on the dipstick that...
There is no way to reset the light. If the light is on, then eitherthe coolant is low, the float is stuck or the sensor is bad.
Answer . \nBest bet is to go to parts house and see if they can pull up a diagram of the serpentine belt pathway. Possibly NAPA parts may have this.
Hi, In most cases these heaters are NOT installed. About the only exception is if it was added by a dealer where it was originally sold. This happens more often when the van is sold in COLD climates. If it was installed as recommended by the factory, you should see an AC power cord tied up on...
Answer . NO your car will run hot and seriously damage your motor, it will also keep from charging your battery. Suggest you take your car to a mechanic for repairs.
Bad switch or bad motor is most likely cause. Motors should have been recalled by Chevy. If you replace motor, replace with new one- do noy replace with a rebuilt motor.
It could be as simple as a soft right front tire, check the air pressure in all the tires.
Answer . The oil sending unit is located on the backside of the engine, towards the middle, but closer to the driver side. It may be a little difficult to see from the top, as it's positioning is a bit awkward, but you can spot it from the bottom. It is easiest to replace if you have access to a...
Instead of an OBD2 Try the older type OBD reader. Your reader is probably for newer vehicles.
Replace wiper motor with a new one. Do not install a rebuilt motor on this vehicle.
Right side of dash,open pass door, it's on side of the dash behindsnap panel.
I realize this question is for a Chevy Venture van, but I found the answer to this code for my venture van here. That code is the EGR. I'd start by checking for a bad connection on the EGR plug-in. Pull the connector off and inspect each individual terminal inside the plug and the connector pins...
There are two small cabin air filters that are located behind the glove box and are accessed through the glove box. There is a small access door that can be removed and then you can pull out the filters. If these have not been changed, it could cause the air to smell from the air conditioner. These...
i think you cannot reset, you need to buy a new air bag ecu
These are called daytime running lamps it is for safety reasons ====================================================== if you want them to not come on all the time, then remove the fuse labeled "DRL" (daytime running lights). It is located in the fuse panel on the right side of the dash with...
Answer . \nThe inner tie rod is part of the Rack and pinion set. VERY expensive.
Answer . Might Be Yr running out of oil, or water levels are low.
loosen the alternator and take off the old belt while your doing that watch how it comes off and put the new one on the some way after that tighten the belt back up and ur done
Hi, That particular code - P0560 - says that the PCM (Powertrain Control Module or "engine computer") has detected that the "System Voltage" is not correct. This usually means that either your battery is going bad, or you have a poor connection between the battery and the PCM - at the...
Hi, The courtesy lights are really controlled by the Body Control Module (BCM), but there is a main fuse that supplies power for the courtesy light function. I believe it is fuse # 35 in the fuse panel that is located in the passenger side dash panel. I have included a link that has a picture...
I had the same problem with my 1998 dodge ram 2500 truck. The power locks stopped working on both sides and quit responding to my remote unlock button. I read that if you disconnect the battery, things will reprogram....Well, I simply disconnected the red cable for a couple minutes and when I...
NO . Go down to you local Auto Parts store and I am sure they will be happy to help you. You just replace the Halogen bulb. It is accessed from the rear under the hood. Go ahead and replace both sides at the same time. They have about the same life expectancy, and the other one will burn out very...
My 2000 Chevy venture gets 24- 25 on the highway.
I don't have the answer but I gave the final solution on my own venture 1999, (although I adjusted and tighten hard the blades bolts, it was tangled-up a number of times on the highway winter time mostly especially one time I was on the passing left, an 18 wheeler and when I was half way...
Replace the wiper motor with a NEW one (do not use a rebuilt!)