Answered

Frequency Scanners

Parent Category: Amateur Radio
Scanners can monitor a variety of things: police, fire, EMS, and even air traffic. Although they can't transmit, they are still very useful.
When you set up aUniden Bearcat BC148XLT base scanner, you must program thefrequencies you want to scan based on your area's frequencies. Youdo not need to include weather frequencies, because the BC148XLTincludes weather frequencies pre-programmed in the base. You canadd frequencies to your scanner...
I have the same one it is hard but try the hold button and messwith it more.
you can PROGRAM it by following the directions here: http://support.radioshack.com/support_electronics/59448.htm P.s. it helps if you can spell PROGRAM (not pragram).
Right here if you had bothered to goggle it? http://support.radioshack.com/support_electronics/doc65/65429.pdf
A less technical answer of how you hear the police through a scanner is much like how you get to listen to music on your radio. There is a transmission site that broadcasts over an area. Equipment such as your scanner is setup to capture those frequencies and play it through the speaker. Many...
For a comprehensive database of active frequencies and systems in your area, and a lot of other useful scanning information, visit the related link below.
I assume you mean radio scanner frequencies? If so, RadioReference is an excellent resource: http://www.radioreference.com/ If you are talking about error codes from your car, you might have to Google those. I'm not sure if OBDII codes are universal (they very well may be). You could do a search...
For a comprehensive database of active frequencies and systems in your area, and a lot of other useful scanning information, see the below site:
See the related link below to listen to live police scanners in the world.
Follow the link below to download/print the manual for your scanner. It will answer all of your programming questions: http://www.uniden.com/pdf/BC72XLTom.pdf
The Best source I've found is at the related link below, but you can frequently find a good buy on eBay.
Your scanner uses a standard BNC antenna connector. Check eBay and ScannerMaster.com for available antennas.
For a comprehensive database of active frequencies in your area, along with a lot of useful scanning information, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, along with a lot of useful scanning information, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, along with a lot of useful scanning information, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, along with a lot of useful scanning information, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, along with a lot of useful scanning information, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, along with a lot of useful scanning information, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
For a comprehensive database of active frequencies in your area, visit: www.RadioReference.com
Many ocean going vessels operate on HF bands and use satellite radios, none of which are accessible by most scanners. There are standard VHF frequencies/channels used by many boaters and ships though, and you can follow the link below for a complete list of them: http://www.navcen.uscg.gov...
The frequencies for aircraft communication vary greatly by location and operator. Your best bet for following the action in your area is to search the civil aircraft band (108 - 137 MHz) and, if your scanner covers it, the military aircraft band (225 -380 MHz). Note the active frequencies that you...
No. Answer #2 As far as fixed wing airplanes it is possible to hear the communications from either the aircraft or the control tower or both depending on the distance from them to you. Other types of aircraft such as helicopters can be listened to as well if they have an open system and can be...
How do yoi unlock the radio code for 2005 acura mdx
Programming a PRO-70 radio scanner . Press the PGM button . Enter the channel number desired to store the frequency . Press the PGM . Enter the frequency you wish to program into the scanner . Press the E/L-OUT button to program the frequency into the scanner After the last step the The...
For a comprehensive database of active frequencies and systems in your area, and a lot of other useful scanning information, visit the related link.
From speedy searches to saving area, there area unit variousadvantages to scanning your documents with OCR software: No additional retyping If you lose or accidentally erase a very important digital file,like a proposal or invoice, however still have a tough copy, you'llbe able to simply replace it...
One place for a free download-able manual in PDF format is at the Radio Shack website. The actual address is listed below in the Related Links section.
For a comprehensive database of active frequencies and systems in your area, and a lot of other useful scanning information, visit the related link below.
If this question is in reference to scanner frequencies, see related links. If the question is about something else, please ask a more specific question.
you don't , it's programed with freqs Programming BC350C scanner Please reference the link below. Programming the scanner begins on page 24. The link provides a page that allows you to view it in .pdf format.
Most of the Motorola FRS and GMRS radios are.
Answer . \nTHE VW RADIO REQUIRES A SPECIAL STEREO REMOVAL TOOL THAT WAS DESIGNED FOR FORD. IT IS A "U" SHAPED TOOL WITH TWO KNOBS ON EITHER END. IT CAN BE PURCHASED ALMOST ANYWHERE THAT STEREO EQUIPMENT IS SOLD. ONCE INSERTED IN THE FOUR HOLES IN THE FRONT OF THE STEREO IT SHOULD PULL RIGHT OUT
For a comprehensive database of active frequencies in your area, along with a lot of other useful scanning information, visit: www.RadioReference.com
First make sure that there is a live battery in the scanner. The battery is located under the plate on the rear of the scanner, you can remove the plate with a philips screwdriver and put a fresh 9v battery in. Step 1. Turn on the scanner and put it in manual mode. Step 2. Flick the Manual switch...
For a comprehensive database of active frequencies and systems in your area, and a lot of other useful scanning information, visit the related link below.
For a comprehensive database of all active frequencies and systems in your area, visit the related link below.
For a comprehensive database of active frequencies (they're not codes) in your area, and a lot of other useful scanning information, visit the related link below.
I'm having a hard time programing a regency r1070 scanner. Can someone help me?
For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit the related link below.
in most places its only illegal if you do it while driving in a car. Added: . . . and if you use the scanner to aid or abet you in the commission of the offense, or to elude law enforcement afterwards.
it takes a 8 digit number example 1550.0100 palestine Texas
Click on the link below for more information.looking forfrequencies for venange county pa
Try the Radio Relay website (see related link at the bottom). I know I was able to listen to Johnston County on there (as well as Wake, Durham, and Orange), so I'm pretty sure Onslow would be on there, as well. At a very minimum, you should be able to get something from Jacksonville.
One should program a Regency Scanner with the model number r1077 by first turning the device's power on. Then press the manual button until the channel wanted is shown. Once the channel number is shown hit enter, which will make the frequency channel that number. Then one can go to the next channel...
Frequency Coverage: VHF-Lo: ................................ 29 MHz -50 MHz (in 5kHz steps) Ham: ................................... 50 MHz -54 MHz (in 5kHz steps) Government: .......................... 136 MHz -144 MHz (in 5kHz steps) Ham: ................................. 144 MHz -148 MHz ...
With radio on, press manual, enter the group you want the new freq to be on. 1-5. enter the channel, enter the freq by pressing the number keys, press enter. The desired freq should remain on that channel until changed. Press manual for the next channel to be progrqmmed. The 250 is the best scanner...
In the related links there should be an scanner.
Both Amazon and eBay web-sites have many frequency books for sale - both new and second hand.
Try going to a Police Radio 10 Codes website.
There are several ways. First, turn the scanner on and adjust thesquelch so that it is quite. Then press the manual button to flipthrough the 16 channels. Stop on the channel you want to program.Then, type in the frequency followed by the "E" key on the lowerright of the keypad. Hit the manual...
Fire and Rescue 154.325 Police ???????? If anyone knows how to scan the police via hand held scanner let me know.
There are several ways. There are several books or guides in publication. Radio Shack generally has several, or check your local library. There are several web site dedicated to "scanner" frequency list. There are also links to monitor local frequencies available through most major Local new...
Try programing in 000.000, if that does not work then you can just lock the frequency out or program over it.
You can listen to the Scotts Bluff County scanner online by visiting the related link below.
The squelch adjustment sets a threshold for the signals/transmissions that you hear -- it lets you listen to actual transmissions without hearing the "dead" noise when a frequency is not active. With the radio on and set to a specific frequency, turn the squelch down until you hear the noise, then...
You don't. A modern scanner is capable of receiving the frequencies listed in the operating manual, and no more. If you need wider coverage you'll need to purchase a scanner that provides it. Bill B Listening in since the 60's
An electronic frequency counter, spectrum analyzer, or anoscilloscope, among others. A much older method is by the use of vibrating reeds! Meters were constructed using thin metal reeds, which were resonantat particular frequencies. For example, a meter used to measure 60Hz. could have five reeds...
first power up t then hit manual then go to channel 1 and hit 155.250 and do this for all of the channels :)
Turn on the radio Press the "band" button Keep pressing the "band" button until you come within the parameters of the frequency that you want Let the radio scan until it gets close to the actual frequency that you're looking for Press the "hold" button and use the arrow "up" or "down" button...
You need to connect to a Comm port on a computer and use software found on the internet. It is fairly simple once you find a puter with the com port. I am not aware if a usb can be converted/used.
depends reallyy :L nahh i dont think soo!
See the related link below for an easier to read manuel for Radio Shack PRO scanners.
These codes are NOT universal across the country and could mean different things in different agencies.
encase the neighbors house inside of a grounded Copper Screen room and they will not be able to pick up any radio signals at all except what comes from equipment within their home
It means they have triangulated a person who is listening in on their radio.
Start by turning the unit on with the POWER button. Push the MANUAL button. Push until you see the Channel you want to enter the frequency in -i.e: Ch 1 Ch2 CH3 etc. Enter the frequency with all the digits needed - i.e: 44.94 / 44.98 / 154.965 / 155.610 etc Then push the ENTER button. The frequency...
There are scanners that can allow the average person to listen to police calls, but they may be somewhat hard to find. Many years ago, the "police band" was 1650 to 1750 kHz, and large home radio sets were able to tune those frequencies - people sat at home on dull evenings and listened to police...
The high frequencies used on scanner channels cross over into the area where there is a lot of random "white noise", a harsh, loud "hiss". Squelch turns the gain down below the hiss, but hopefully not below the signal. It has to be adjusted carefully, otherwise you eliminate the signal along with...
a code 1084 means 2 things : 10 designates that the unit requesting the dispatch is a police officer, and 84 means all units available nearby (within a set radius) respond to deadly (or will be soon) situation. usually not used unless a suspect is either armed and resisting custody or...
01) Press Manual to enter the manual mode. 02) Enter frequency. 03) Enter channel number (e.g. for channel 1, enter 01). 04) Press Manual again. Note: When entering a number of channels, you can start at step 2 after the first frequency is entered.
If you mean: how reliable is the information you hear on a police scanner, then fairly so, though it's possible the people are relaying untruthful information given to them by an unreliable third party or reporting their (possibly mistaken) impressions and observations of the moment. It's also just...
you cant. doing so requires special equipment more advanced than a police scanner. police in some areas use cell phones over their radio for privacy issues. for example if police are busting a party for underage drinking, they use cell phones to communicate so that anyone who has a scanner cant warn...
See the related link below for the link to RadioReference.
It means they have understood what has been said during a conversation in a radio transmission by saying Roger which means ok
Its believed that when they are discussing investigative information they go offline ,due to the private nature of the information shared. To prevent possible suspects from getting the information and possibly get away. It may also be to cover corruption on the force ,such as racial slurs etc. I...
it doesent have pictures because its a radio and radios are not objects that you can see things on only hear
There is no single frequency for Denton City PD. The Denton City PD uses a talkgroup on a trunked radio system (0B12 is the system ID, 105.88 is the connect tone, control channels 857.31250, 858.31250, 859.31250, and 860.31250 MHz) shared by the city (shared with fire, waste, city management, water,...
Hit manual go to what channel you to program hit Program inter the freq you want to program hit Enter. that is how you program a Pro 46. Good luck. I have a Pro 46 and I think it is one of the best older Police scanners you can own. tom
You have to select the channel, then press the PGM (Program) key, then select the frequency (example: 155.6100) making sure you use the decimal key. Then press enter.