answersLogoWhite

0


Best Answer

The headlamp bezel must be removed and then you will be able to see the mounting bolts. Try not to disturb the headlamp aiming adjustments. Now, on the large composite headlamps, the bulb can be replaced from the rear by unplugging the wires and turning the large plastic cap ccw. But the question was about the assembly, so just unplug the wires and remove the mounting bolts.

User Avatar

Wiki User

16y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

14y ago

You do mean the whole thing. There are 3 clips to remove from the inside, use a screw driver. The whole lens then comes out from the front. If you just mean the bulb, then just un-screw the bulb holder, ( 1/2 turn ) then replace the bulb.

This answer is:
User Avatar

User Avatar

Wiki User

18y ago

I believe you can get acess to the fasteners behind the carpet in the trunk.

This answer is:
User Avatar

User Avatar

Wiki User

9y ago

Remove the wiring harness from the tail light assembly in your 2005 Mercury. Remove the tail light assembly retaining bolts. The tail light assembly will come out.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove the tail light assembly and lens on a 1988 ford crown Victoria?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace stop light bulb in 1999 ford crown Victoria?

If it is the same as all Crown's: open the trunk, remove the plastic wing nuts that hold the whole tail light assembly (there ares 4 or 5), then pull out the assembly from the outside. Lights are there.


2005 ford crown Victoria How do you disable the dome light from turning on when the door opens on a 2005 ford crown Victoria?

There should be a SWITCH at the dome light! If not, remove the fuse from the fuse box above where your gas pedal is. OR: Simply remove the BULB from the dome light. duncanw.


How do you fix the hazard light switch on a 97 Crown Victoria?

Remove the wiring harness from the back of your 1997 Ford Crown Victoria hazard lights switch. Remove the hazard light switch retaining screws. Reverse the process to install your new hazard light switch.


Does a 1991 crown Victoria tail light fit a 1989 crown Victoria tail light?

Yes, they are identical


How do I change the Check engine light bulb in a 1996 crown Victoria?

To change the check engine light bulb on a 1996 Crown Victoria you need to remove the molding from around the instrument panel. Next, remove the headlight knob and shafts. Locate the light bulb and turn counterclockwise to remove. Reverse directions to replace with a new bulb.


How to change side marker bulbs 2000 Ford Crown Victoria?

Front marker lights can be changed by removing front headlight assembly. To remove pull up on two metal clips behind light assembly and unplug wires. The side marker lights are now accessable. Turn bulb socket ccw to remove.


How do you change tail light bulb on 1996 ford crown Victoria?

open trunk, remove the 4 wing nuts, remove the casing from the outside. Bulbs are in there.


How do you replace 1998 ford crown Victoria head light assembly?

Once you remove the plastic cover over the headlights, you will have either 2 slide up locks, just slide them up unplug the wires and the housing pop's out. Or, 3 clips that with a screw driver just pop open and the assembly pop's out.


How do you remove 99 Crown Victoria headlamp?

If you want to change just the bulb, remove the small plastic on top of the light from the engine compartment, and turn the light even with the wire harness attached, the bulb will come out.


How do you replace the corner amber parking light bulbs on a 2003 V8 Crown Victoria?

Pull back the trunk's liner. There will be about 5 large plastic wing nuts. Remove these, and pull the tail light lens assembly away from the car. The socekets will then be accessible. For the front corner lights open the hood and remove the cowl piece over the headlights by removing about 5 twist lock fasteners. Next remove one 10mm nut from a stud coming up from the back side of the corner light assembly. Remove one Philips screw from the back of the outside of the assembly and remove the entire piece. you now have access to the socket that holds the bulb.


Where is the dome light door switch located on a 1999 p71 Crown Victoria?

on my 98 crown vic you have to push in the head light switch


Replace the Rear turn signal bulb 1997 Crown Victoria?

With the trunk open, there are 4 wing nuts that hold the light casing in place. Remove them and pull the light casing out from the outside.