You must find a resistance value for 0 dB as reference.
If 1 Ohm = 0 dB then 10 ohms = 20 dB and 100 ohms = 40 dB.
3000 ohms are 3 kiloohms.
A Megohm is one million ohms. To convert ohms to Megohms, divide by one million.
You have to convert all values to ohms. 3 kiloohms = 3000 ohms. 3 micoohms = three millionth of an ohm = 0.000003 ohms. The product is: 3000 times 0.000003 = 0.009 ohms squared.
Ohms is a measure of impedance (resistance), not volume.
It depends if the are in series or parallel. In series: 55K ohms In parallel: 5K ohms It really all depends brah.
You'll need to decide *which* one you want. An impedance-matching transformer has a defined primary-to-secondary turns ratio. This *may* give the level match that you want, it may not. Alternately, you can design for a level match, which also *may* give the impedance ratio you want, it may not. It also has a defined turns ratio, but this may not meet an impedance-matching requirement. For impedance matching find the ratio of impedances, take its square root, and use that as the turns ratio: 2400 ohms to 600 ohms has an impedance ratio of 4:1, so its turns ratio will be (sqrt4) = 2:1. To level-shift 1.23 volts (+4 dB) to 300 mV (-10 dB), the ratio is (1.23/0.3) approx 4:1. From the above, you could match 2400 ohms to 600 ohms, but *not* +4 dB to -10 dB with the one transformer.
The decibel scale is a logarithmic scale where each change in three dB represents a power factor change of two. (3 dB is power times two, 6 dB is power times four, 9 dB is power times 8, etc. Similarly, -3dB is power divided by two, -6 dB is power divided by four, etc.) Zero dB is assigned some arbitrary reference power. One example is 1 mV across 600 ohms. If you double the voltage into a constant resistance, the power quadruples, so 2 mV would be +6 dB, 4 mV would be +12 dB, etc. The letter after dB is the reference power. In the case of dBm, it means that 0 dB is 1 milliwatt, so 2 milliwatt is +3 dB, etc. There are many dB scales, such as dBa, used in sound measurements. Still, fundamentally, 3 dB is a doubling of power, -3 dB is a halving of power, so, for any arbitrary scale, say dBq, then saying +6dBq is saying a power four times higher than 0 dBq. In the end, dBm plus dBm is delta dB, with no scale.
A Db E Db A Db E Db A Db E Db A Db E Db Ab Db E Db Ab Db E Db Ab Db E Db Ab Db E Db Gb Db Gb(higher) Db Gb Db Gb(higher) Db Gb Db Gb(higher) Db Gb Db Gb(higher) Db fqggbegjg2y7gdsjnjnagydsaytdgtewydtwfe
The difference in between Ohms and Ohms CT is that in Ohms CT it has CT at the end.
3000 ohms are 3 kiloohms.
Ohms are smaller than k-ohms, so number of ohms must be a bigger number. Multiply k-ohms by 1,000 to get the same resistance in ohms.
135 ohms new, and will function properly down to 114 ohms. The chart in the '86-'87 book shows: Empty=110 ohms +/- 7 ohms Full=3 ohms +/- 2 ohms 1/2 full= 32.5 ohms +/- 4 ohms
yes it = 1
dB mean Decibel.
90
A Megohm is one million ohms. To convert ohms to Megohms, divide by one million.
The threshold of hearing is 0 dB. The threshold of pain = 137.5 dB.