answersLogoWhite

0


Best Answer

First is the angle of the roof rafter. This MUSt be established BEFORE any cutting takes place.

Identify the wall plate (normally a 4 x 2 (2 x 4 if in the US)timber across the top of the wall of the building. The plate sits with the 4 inch face flat on the wall with the 2 in high side vertical to the wall.

Measure the horizontal cut, called the seat. Trace a horizontal line straight across the surface of the rafter or stable brick. This line marks where the top of the joist (or other brick) must meet flush with the rafter (or stable brick).Subtract the thickness of the wall. Measure the wall -- six inches, for example -- and subtract it from the length of the seat line. Dot this mark on the seat line.Then mark the plumb, or vertical, line. Align the measuring tape vertically with the dot on the seat line. Trace the vertical line, straight down to determine where the side of the joist (or other brick) meets flush in the rafter (or stable brick). Cut out the "bird's mouth" angle to fit in the frame.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you cut a birds mouths in a rafter?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you cut a birds beak in a rafter?

with a saw.


How do you cut rafters with different plate heights?

If the plate height gets higher increase the depth of the birds mouth that sits on the plate. The birds mouth is the notch cut out of the rafter that allows it to sit flat on the top of the plate. If the plate is low then you will need to place a packer on top of the plate.


Why do birds have their mouths open?

to eat, or to sing, or to vomit into the mouths of their children


What is a jack rafter or called a cripple?

A Jack rafter is a rafter that has the pitch of the roof cut onto one end with a 54 degree angle this sort of rafter is one of several that fit onto a hip ridge. To cripple a piece of timber means to cut it partway through in order to straighten it if this is done to a wall timber it will need to be splinted to restore the strength of the stud


What of you call a group of turkeys?

Gaggle


Instructions for swires roofing square?

The figures on the outer edge of the curve are degrees. Use these to set the angle/pitch of the roof. The figures on the inner edge of the curve are a ratio of the length of common rafter per foot or metre of run or span of roof. Take half the span of the roof in feet OR metres and multiply by the figure for the pitch of your roof this will give you the length of your rafter from birds mouth to the centre of the roof. Then make a deduction of half the thickness of the ridge board. at right angles to the bevel . The easiest way to use the bevels/angles from the square is to place the square on a piece of ply or board and mark all the bevels/angles onto the board and then use a sliding bevel/bevel square to apply the bevels/angles to the rafters and other members of the roof. No 1= Plumb & Seat cut for the Hip No 2=Plumb & Seatcut for Common Rafter No 3=Edge cut for the Hip (Mitre) No 4=Edge cut for Jack Rafter No 5=Side cut for Purlin No 4A=Edge cut for Purlin (Mitre) No 6 Lip cut to Purlin .This is the sloping cut which goes under the bottom edge of the Hip where the Purlin abutts to the Hip Rafter


Do birds use their tongues to drink?

Birds use their tongues to taste, they use their beaks/ mouths to drink.


What is the birth name of Patrick Rafter?

Patrick Rafter's birth name is Patrick Michael Rafter.


How do you cut a valley rafter with a compound miter saw?

You set the bevel on your saw to a 45 degree angle. Then set the angle on your saw base to the angle of your plumb cut.


When did Charles Rafter die?

Charles Rafter died in 1935.


When was Leonard Rafter born?

Leonard Rafter was born in 1912.


When did Leonard Rafter die?

Leonard Rafter died in 1964.