0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What type of welding machine is not suitable for E308L-15 electrodes?
3 types Of welding machine suitable for E 308-15 electrodes?
Why do we use rectifier kit?
Working the rectifier
What is Welding Speed and Welding time for Co2 Welding Process?
Your question is incomplete. Which process? Which electrode? What is the basemetal, which position? etc etc
What is the difference between welding rectifier and welding transformer?
A rectifier is an arrangement of diodes (devices that only allow current to flow in one direction), half-wave or full-wave, that converts AC to pulsated DC. A capacitor (condenser) is used to smooth out the pulsated DC for a more true DC supply. A transformer is usually comprised of two coils of wire around an iron core that changes the ratio of input voltage/current to output voltage/current. It does this by induction (a magnetic field crossing through a coil of wire producing electricity). The Primary coil (the input) usually is a bit thicker and has less windings than the Secondary coil (the output).
What is use of rectifier?
Rectifier is used to convert alternating current to direct current.
Why is a transformer rectifier often prefferred for smaw?
SMAW stands for shielded metal arc welding. The rectifier used in the welding machines must be referring to this type welding.
What is rectifier welding machine?
A welding rectifier takes in the a/c output of a welding transformer, and the output is d/c. Used with old school welding transformers which were all a/c, in order to get d/c for use with low hydrogen rods etc.
What type of welding machine is not suitable for E308L-15 electrodes?
3 types Of welding machine suitable for E 308-15 electrodes?
What kind of rod is use for braze welding?
Brazing isn't welding - it's more like soldering. You use a rod made out of brass for the process of brazing.
What is Welding process?
There is no BEST process for all conditions/situations/materials/applications. Easiest to use would probably be GMAW (MIG welding). Most useful for all applications and metals including cutting OAW (Oxy-Acetylene welding) usually referred a to as Oxy-Fuel. Most widely used process is probably SMAW (stick welding) which would also be most portable and cheapest to purchase. GTAW (TIG/Heliarc) is used mostly indoors on thinner and or non ferrous metals ( Aluminum, Stainless Steel, and most alloys. If I were to set up a shop at home I would consider a DC stick welding machine (preferably a rectifier type) and an Oxy-Acetylene setup.
What welding process is best?
There is no BEST process for all conditions/situations/materials/applications. Easiest to use would probably be GMAW (MIG welding). Most useful for all applications and metals including cutting OAW (Oxy-Acetylene welding) usually referred a to as Oxy-Fuel. Most widely used process is probably SMAW (stick welding) which would also be most portable and cheapest to purchase. GTAW (TIG/Heliarc) is used mostly indoors on thinner and or non ferrous metals ( Aluminum, Stainless Steel, and most alloys. If I were to set up a shop at home I would consider a DC stick welding machine (preferably a rectifier type) and an Oxy-Acetylene setup.
Which gases are used in normal welding process?
Depends on what you think of as normal welding. Gas welding use oxygen-acetylene. MIG/TIG use Argon. MAG, use an argon-something mix. Depending on what materials you are welding, there are some more options tha might be used.
Why do we use rectifier kit?
Working the rectifier
How do you set up a welding rectifier?
A rectifier is a type of welding machine. Fairly new development that changes common electrical supplies to voltage and amperage that can be used to weld. It uses less electricity than standard welding machines (usually transformers). It will require a certain supply (voltage - amperage) that you connect the machine to and should state the minimum requirements somewhere on the machine.
What is Welding Speed and Welding time for Co2 Welding Process?
Your question is incomplete. Which process? Which electrode? What is the basemetal, which position? etc etc
What is the difference between welding rectifier and welding transformer?
A rectifier is an arrangement of diodes (devices that only allow current to flow in one direction), half-wave or full-wave, that converts AC to pulsated DC. A capacitor (condenser) is used to smooth out the pulsated DC for a more true DC supply. A transformer is usually comprised of two coils of wire around an iron core that changes the ratio of input voltage/current to output voltage/current. It does this by induction (a magnetic field crossing through a coil of wire producing electricity). The Primary coil (the input) usually is a bit thicker and has less windings than the Secondary coil (the output).
What is filling pass in welding?
Filling pass is a welding process which function to filling filler metal inside welding groove before capping process be execute
