0
The cord should have a green,white,red,and black wires in it. Green is ground, white is neutral, and red and black are "hot". On the plug the green terminal is for the green wire, the silver terminal is for the white wire, and the brass terminals are for the red and black wires. Simple job for a pro and will cost little. If you have to ask and depend on the answers from people like me, saving money is more important than your Family and Home..Good Luck...pkazsr
Wiki User
∙ 18y ago
Wiki User
∙ 13y agoYou must have a commercial electrician's license to install a commercial oven in a commercial building. Although your question does not indicate commercial use, I wouldn't tell you how to do it for legal responsibilities. I wouldn't want to endanger you or your family either in your home.
Wiki User
∙ 9y agoYou are approaching the problem the wrong way around. The cord to the dryer should stay a four wire as that is now the new electrical code. What should be done is changing the three wire wall receptacle to a four wire installation.
Turn the breaker off that controls the circuit for the dryer. Look in the back of the dryer receptacle box that is in the wall. The three wires coming in should have a bare ground wire in the cable set. It wasn't brought to the receptacle because there was no place for it on the old three wire receptacle. If you find the ground wire back there under a screw terminal, just add another short piece of wire under the screw and then connect the other end of the short wire to the new ground terminal on the new four position receptacle. The wire should be equal in size to the size of the wire that exists around the ground terminal now. If the house is so old that the range cable did not have a ground wire in it, the electrical code allows a separate green ground #10 wire to be taken from the breaker panel box to the existing range receptacle. This wire is to be bonded on each end. At the panel end to the ground buss and at the receptacle end around the ground screw at the back of the box unbroken and then to the new four position receptacle ground lug.
Wiki User
∙ 11y agoyou probably have a 3 phase cable?
Add your answer:
Earn +20 pts
Is 8 3 wire too big to hook up an electric dryer?
no
How do you wire a 220 3 wire breaker to 4 wire dyer?
Buy a 3 wire cord for your dryer.
Can you convert 4 prong dryer cord to 3 prong?
Probably not. The reason is the amperage required by the electric range. They typically require 50 amp whereas a dryer normally only requires 30 amp. Therefore, the wiring feeding the dryer is not large enough to support an electric range. Your range should be wired with #6 or 8 gauge wire, whereas your dryer is likely only wired with # 10 gauge which will not carry 50 amps.
What are the different sizes for plugs on a US dryer?
50 amp 3 and 4-wire.
Should a 3 wire 250 volt drier be grounded?
Yes, most definitely. Provisions for the ground wire in the dryer receptacle should be used. The feeder cable's ground wire is first grounded to the receptacle's junction box ground screw and then taken to the receptacle's ground terminal. The dryer plug configuration will match up to the dryers four wire plug in cable. When the plug is connected into the dryer receptacle the ground terminals of both devices will match and the ground wire will be continuous from the voltage source at the distribution panel and complete the circuit at the dryer. This low impedance electrical path will conduct any ground fault that could occur at the dryer and trip the feeder breaker of the dryer circuit, there by removing the fault current from the dryer circuit.
Is 8 3 wire too big to hook up an electric dryer?
no
Can you use 10 3 which is 4 wire to hook up a 3 wire dryer outlet?
If you're using 10/3, then you may as well use a 4-wiredryer receptacle, provided that your dryer is rated for 30 Amps. The NEC in America actually requires this now.
Is it necessary to connect the ground wire to a 4-prong 240V outlet - I am switching a 3-outlet to a 4-prong outlet for my new dryer but the ground wire is cut off so I can't connect it?
Only if you wanted to fry your hair.for God sake(and yours)buy a new cord to hook up your dryer
How do you wire a 220 3 wire breaker to 4 wire dyer?
Buy a 3 wire cord for your dryer.
How do you hook up a universal 4 wire oxygen sensor when the OE was 3 wire?
get the right oxygen sensor
Can you convert 4 prong dryer cord to 3 prong?
Probably not. The reason is the amperage required by the electric range. They typically require 50 amp whereas a dryer normally only requires 30 amp. Therefore, the wiring feeding the dryer is not large enough to support an electric range. Your range should be wired with #6 or 8 gauge wire, whereas your dryer is likely only wired with # 10 gauge which will not carry 50 amps.
On three wire spin dryer cord which color green white?
On a 3 wire dryer cord there is no green wire. The white wire coming from the outlet is connected to ground or the green screw. The black and red wires are the hot wires.
How do you wire 12 V lights to 36 V batteries?
You get 3 of them and hook them up in series. Then you can connect them to the 36 V battery.
What are the different sizes for plugs on a US dryer?
50 amp 3 and 4-wire.
Should a 3 wire 250 volt drier be grounded?
Yes, most definitely. Provisions for the ground wire in the dryer receptacle should be used. The feeder cable's ground wire is first grounded to the receptacle's junction box ground screw and then taken to the receptacle's ground terminal. The dryer plug configuration will match up to the dryers four wire plug in cable. When the plug is connected into the dryer receptacle the ground terminals of both devices will match and the ground wire will be continuous from the voltage source at the distribution panel and complete the circuit at the dryer. This low impedance electrical path will conduct any ground fault that could occur at the dryer and trip the feeder breaker of the dryer circuit, there by removing the fault current from the dryer circuit.
What gauge of wire to connect electric dryer?
You need a 3 conductor #10 cable. A #10 wire is rated at 30 amps.
8 wire vs 10 wire to install a dryer?
Dryers are on 30-amp circuits, as are water heaters. Ranges are on 40-amp circuits. The National Electrical Code calls for 10/3 wire for a dryer. The version now in use calls for "10/3 WG" wire - WG means "with ground" meaning there are four wires in the jacket - a bare one that's your ground, white which is the common wire, red and black which are your hot wires. You don't NEED to use 8AWG on a 30-amp circuit that's less than 100 feet from the breaker to the outlet, but it's legal and some people do. If you needed 30 feet of wire to hook up the range, 12 feet for the dryer and 8 feet for the water heater, it's cheaper to buy one 50-foot roll of 8/3 than to buy the three wires you need by the foot.
