0
If you go to www.swanstone.com and search and click for your particular shower base, you'll find installation instructions. Or you can call (800) 325-7008.
Wiki User
∙ 14y ago
Wiki User
∙ 12y agoyou plug it in
Add your answer:
Earn +20 pts
Can you tile over a stone shower base?
Yes you can just use a better mortar and smaller tiles
What are the steps to make a complete shower after the drain is set?
The center of the shower floor where the tile shower drain would normally be positioned ... drain base. After this step the sloped mortar bed should be ... pan liner or membrane in our instructions.
How to Install Mortar Shower Pan Membrane Liner?
How to Install Mortar Shower Pan Membrane LinerOnce you've framed the shower stall, it is time to install the pan liner and cement backer board to create a water tight seal.Remove the drain cap and tape over the drain to keep mortar and other debris from entering the drain. Put down a layer of felt paper to help prevent moisture from wicking down through to the subfloor. Place a layer of metal lathe over the felt paper. Trowel in a layer of mortar that it has a one quarter inch slope towards the drain. Once the mortar dries, place a layer of felt paper along the walls of the shower stall. Attach cement board with the rough side out along the top half of the walls. Install the shower stall membrane in the bottom of the shower so that it overlaps in the corners, covers the shower curb and is approximately six inches up the side of the walls. Cut out holes for the drain, the drain bolts and the weep holes. Seal the underside of the membrane near the drain with silicone. Nail the membrane that covers the curb only on the outside. Attach the remaining cement board leaving one inch clearance from the bottom. Caulk all seems. Place some pebbles near the weep holes to protect the openings. Trowel in a layer of mortar that has a one quarter inch slope towards the drain. Mortar the curb. Remove the tape from the drain.
What is the cost to install a fiberglass shower?
what is the cost to install a fiberglass shower
How is a shower tile permanently attached to a base surface?
Shower tile is permanently attached to a base surface by first, cleaning and completely drying the shower base. Then one spreads mortar over the entire surface, press the tiles into the mortar, spacing them 1/4 inch apart. Place spacers between each tile and allow to dry for 12-18 hours. After it's dry, remove the spacers and spread grout over the top, wiping off any excess, and then allowing to dry for another 12-18 hours.
Shower Installation?
form_title=Shower Installation form_header=10813 What changes are going to be included with this shower installation?*= () Replace or move existing shower () Install a new shower (No existing shower) Plumbing fixtures*= () Yes - I plan to install new plumbing fixtures () No - I do not plan to install new plumbing fixtures Would this particular project be a part from a larger remodel?*= () Yes () No Tile*= () Yes - I plan to install new tile () No - I do not plan to install new tile Can you specify the type of shower you want installed?*= () Free-standing shower () Steam shower () Shower / tub combo () Dual shower
What is the cost to install safety grab bars in a shower?
The cost for install safety grab bars in a shower is around $30.
Installing A Shower Unit?
How to install a shower unitHomeowners who want to install a shower in their home can do the job themselves instead of having to pay someone to do it. Find the materials that you need to complete the shower. You will need the base for the shower, the shower door, fiberglass for the shower itself, and the attachments. Begin by building the base of the shower. Make the base tall enough to keep the water off the floor, but low enough so you can easily step over the edge to get in the shower. Construct the frame of the shower from the wood and then add the fiberglass to the wooden frame. Use caution when using fiberglass because you can get the small glass particles in your hands.Make a door frame that will house the shower door. When you finish with the frame, carefully slide the glass form the packaging into the frame. Use brackets to attach the hinges so that the door will open and shut. Make sure the door closes completely so no water leaks out of the shower. Install the plumbing attachments so you can take a shower as well as any extras you would like in the shower such as towel racks and containers for shampoo.
Mustee Shower Base?
form_title= Mustee Shower Base form_header= Enjoy showering with a Mustee shower base. Do you need to remove an old shower?*= () Yes () No Are you redoing the entire bathroom?*= () Yes () No Do you want the shower base delivered?*= () Yes () No
How does one make a shower in a freestanding claw foot tub?
You must install, or have a plumber install a shower head first. You can install a surrounding shower curtain that allows the curtain to drape on the inside of tub.
Moen Shower Faucets?
form_title= Moen Shower Faucets form_header= Install a Moen shower faucet in your home! What is the size of your shower?*= _ [50] What type of shower head do you want to install?*= _ [50] What color would you like the shower heard?*= _ [50]
Who can install a walk in shower for me in Tempe, AZ?
A local contractor can be contacted. Contractors can install the walk in shower. There are also handymen that will install the showers at lower rates.
