0
How do you program a 2004 Chrysler sebring keyless entry remote?
Wiki User
∙ 10y ago
Q: How do you program a 2004 Chrysler sebring keyless entry?
A: The following works for the 2004 - Chrysler Sebring/Concorde/LHS/300/Voyager/Town & Country, Dodge Stratus/Intrepid/Caravan/Durango/Dakota/Ram 1500, Prowler, Jeep Liberty
Program Method
1. Press (LOCK) button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.
2. Turn ignition to run position. (Allow ignition chimes[UNLOCK] to stop).
3. Using any original (working) transmitter, press the [UNLOCK] button for 4 to 10 seconds.
4. Within the specified 4 to 10 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons. A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).
5. Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and release.
6. Press and release any button on the same transmitter and a chime will sound after successfully programming the transmitter.
7. Repeat steps 5 through 6 to program additional transmitters.
8. Turn ignition to OFF position. Transmitter programming mode will discontinue after 60 seconds. (All transmitter programming must be completed within time specified).
TRY THIS (from the owners manual)
To Program Additional Transmitters:
Up to 4 transmitters can be programmed to your vehicle.
To program a transmitter, perform the following procedure:
1. With the vehicle in Park, turn the ignition switch to the
ON/RUN position.
2. Using a currently programmed transmitter, press the
Unlock button on the transmitter. Continue to hold the
Unlock button, wait at least 4 but no longer than 10
seconds, then press and hold the Panic button for at least
one second. Release both buttons simultaneously. You
will hear a chime to signal that you can proceed with
programming the new transmitter.
3. Press and release the Lock and Unlock buttons simultaneously,
followed by a press and release of ANY button
on each new transmitter to be programmed as well as the
original transmitter. You will hear a chime when a
transmitter has been successfully programmed. You will
have 30 seconds to finish programming all new transmitters.
A chime will sound when the 30 seconds is over or
the ignition switch is turned to the LOCK position.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Does the keyless entry remote on a 2000 Chrysler Sebring use a battery?
Yes.
How do you program a keyless remote for a 2006 Chrysler 300?
You have to have a scan tool.
How do you reset the security system in your 2000 Chrysler Sebring without a keyless remote?
Unlock the doors or trunk with the key.
How do you program a keyless entry remote for a 1996 Chrysler sebring?
You have to go to the dealership to have your keyless remote reprogrammed. They have a scan tool to tell the computer that you are using a new key fob. I just did it to my 1997 sebring. I knew the service manager, so he let me borrow it, it took me about 15 minutes, most will do it for a small fee, some will do it as a courtesy.
How do you program a 2005 Chrysler Town and Country keyless entry remote?
The dealer.
How do you program a Chrysler Sebring remote?
The dealer ship scan tool is required.
How do you program a 2005 Chrysler 300 keyless remote?
The dealer scan tool is required.
How do you program a new remote for a 2004 Chrysler Sebring if you don't have a working remote?
That requires the dealer's scan tool.
How do you program a 1997 Chrysler stratus keyless entry remote?
The dealership scan tool is required.
How do you program keyless remote for a 2001 Chrysler Town and Country?
The dealers scan tool is required.
How do you program a 2005 Chrysler pt cruiser keyless entry remote?
I use a scan tool.
How do you program keyless remote for Chevy Malibu?
How do i you program keyless remote for a 2004 malibu?
