0
ON MY '81, I CAN FIX IT BY ROLLING THE WINDOW TRACK ALL THE WAY DOWN AND ACCESSING THE WINDOW THROUGH THE REMOVED VENT (AT THE BACK LOWER CORNER OF THE DOOR)AND THE SPEAKER HOLE (AT THE FRONT CORNER). THE TRACK HAS A ROUND KNOB THAT MOVES THE WINDOW UP AND DOWN, AND IT'S FACING AWAY FROM YOU. THE REASON YOUR WINDOW POPS OFF IS THAT THE SQUARE PLASTIC PIECE ATTACHED TO THE ROUND KNOB HAS BROKEN OFF. GENTLY PUSH ON THE BOTTOM OF THE WINDOW AND MOVE THE METAL BRACKET (PART OF THE WINDOW) SO THE RECTANGULAR GAP IN THE MIDDLE IS OVER THE ROUND KNOB, AND THE SLOT IN THE METAL BRACKET IS OVER THE CHANNEL EDGE THAT THE KNOB RIDES IN. FROM NOW ON, EITHER HAVE THIS WINDOW ALL THE WAY UP OR ALL THE WAY DOWN. IT WILL FALL OFF TRACK IF IT'S PART WAY.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you get the passage window back on track on a 1994 Pontiac grand am SE?
Remove the door panel. Find the track, for the passage window, loosen the track and put the glass, back in track. Put the track, back in track, and tighten it down. Put your door panel back on, and your ready to go.
How do you put a driver side window back on track on a 1993 ford thunderbird?
Remove the inside door panel. The entire window mechanism will be visible. Put the window back onto the window track.
HOW Do you set a power window back on track on a ford focus?
To set the power window back on track in a Ford Focus, you have to remove the door panel. Once you get in there, you will see the track that you will need to put the window back on.
How do you put dodge Dakota 1993 window back in track?
you need a window regulater you can not just put on track and it can cost some money
How do you put a power window of a Chevy blazer back on track?
You will need to remove the inside door panel of your Chevrolet Blazer. Remove the window retaining clips. Put the window back into the window track. Tighten the window retaining clips.
How do you put a passenger side window back in track on a ford expedition?
To put a passenger side window back on track on a Ford Expedition you should first carefully remove any old silicone. Next put the window back on track, and use Gorilla glue or silicone to secure it. Do not put the window down for at least 24 hours.
How to put drivers side power window back on track?
you cannot put the window "back on track" the window regulator failed and will need to be replaced, good luck. What kind of lame answer is that? Yours might have been - not everybodies is.
How do you put a manual roll up window back on track of a 1994 Chevy Cavalier?
You can put a manual rollup window back on track, in your 1994 Chevy Cavalier, by removing the inside door panel. The window track is easily visible with the door panel removed.
How do you put a drivers side window back in track on a ford expedition?
To put a driver's side window back on track on a Ford Expedition you will have to reseat the window. Do this by removing the door panel and putting the window back in place. You can use silicone or Gorilla glue to attach the window. Leave the window in the up position for at least one day once you have it back on place.
How do you Put window back on track 2000 jaguar s-type?
To put a window back on track in a 1996 Geo Metro, the door panel will have to be removed. Use a screwdriver to pry up the clips around the door panel. Then locate the window cable and rewind it. If the window is operated by a power switch, be careful not to pinch the fingers when rewinding the cable.
How to put driver side window back in the track?
Generic Answer You need to remove the door trim. Then loosen the track, you should then be able to re locate the window into the track
How do you put power window glass back on track?
By pushing the button downwards
