answersLogoWhite

0

How do you remove grout?

Updated: 8/16/2019
User Avatar

Wiki User

14y ago

Best Answer

You can buy a little scraper tool that has a pointed or 'v'shaped end to clean the gap between the tiles without damaging them. after that its a matter of re-grouting. Make sure the area is dry first - rubbing alcohol works well.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove grout?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do I re-grout outdoor mosaic tables?

To re-grout you mosaic tables, simply use tile grout. Be sure to remove the excess grout from the mosaic tiles to preserve the tables beautiful look.


How do you remove solvent based paint from grout?

VERY difficult. -It's easier to paint over it with special grout paint.


How much does it cost to remove grout out of the grout joints?

grout removal and replacement is a hard and long project unless you already have the tools and knowledge, If you hire a tile contractor you are likely to spend anywhere from 2.50 to 3.50 a sq foot depending on the age of the grout and the thickness and width of the grout..........


How do you remove nail polish from floor tile grout?

by adding acetone to it


Can you remove caked in grout from slate tile AFTER it has been sealed?

Well YA! That is how you do it!! :)


Is there such a thing as grout remover?

Yes. You can remove grout around tiles by using a mechanical device that scrapes it away. The tool tip is usually made of tungsten carbide and has several teeth to gouge away the grout. You can either use a fairly cheap unpowered one or a more expensive one that uses power. You can also buy liquid grout remover for removal of grout residue.


How easy is it to remove grout after applying?

Water & a sponge will move it just fine until it sets up then IT is VER hard to remove


What happens if you make a mistake and use non sanded grout in a ceramic tile joint of one quarter inch?

Non Sanded grout can be used in any size grout joint but is ideal in smaller joints usually up to 1/4" The main draw back to using unsanded grout in larger joints is that it may crack over time. If you are unwilling to remove all the grout and use a sanded grout, it is best to make sure the grout is cured and sealed properly to limit and minimize cracking.


When you installed the grout after pressing all the seams your son cleaned up for you he used a rag mop and ended up with low spots can you just wet it and go over it again 0 in to 1 8 in to level it?

It depends on the type of grout you used. Typical cement-based grouts cannot adhere to existing grout in lines of less than 1/8" deep, and it's advisable to remove all the grout and do over. If your grout is an epoxy-based grout, or some varieties of pre-mixed grout, it might be possible. Check the label to see if it adheres to existing grout, and at what thickness.


How do you regrout a pool?

You will need a grout saw and grout scraper to remove the old grout. Then use an epoxy grout meant for swimming pool use, and work in small areas at a time. Choose a color that matches the tiles. Follow the mixing instructions on the container. When all the tiles are properly filled wait for it to dry before finishing the job with a sealant.


How do you apply bathroom grout correctly without it constantly being dragged out?

"Grout is the stuff you apply between tiles to seal them in place. Grout tiles once the adhesive has dried fully (24 to 36 hours later). The best grout is waterproof and mould-resistant; some come ready-mixed. Use a grout float - a rubber-faced tool with foam backing - for large areas. Spread the grout across the tiles at right angles to the joins. Use a damp sponge to remove excess. Once the grout is dry, polish the surface with a dry cotton rag." I was taught by a contractor to apply and clean the grout diagonally.


How to repair white grout in shower?

First you need to remove the damaged grout. Do this by using an old (or cheap!) flat head screwdriver to scrape and dig out the loose grout. Vacuum or brush away any dust. Mix grout mix and latex filler (to make it hard and more water proof) and fill in the spaces. Smooth the grout and then sponge off the excess that is on the tile. Allow to dry for a day and then wipe off again.