0
Before attempting any car repair, be sure to consult an owner's manual.
Begin by gently popping off the horn cover. The short wire that you see will go into a sleeve. Gently tug this wire and rotate it counterclockwise to remove it. The removal will likely cause the horn to beep. Once you've done this to unlock the connector, you can pull the steering wheel off with a steering wheel puller. Under the wheel, remove the black plastic disk, and push the metal notched disk into the wheel to unlock the retainer and remove it. Be careful when removing it as there is a stiff spring underneath it. The white turn signal switch will be underneat this. Remove the hazard switch first, and then turn the signal level screw. Then remove the 3 screws that hold the switch on. Then remove the lock cylinder retaining screw, turn the ignition to the run position and remove the assembly.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Where is the 1996 GMC Jimmy knock sensor located?
The knock sensor on the 1996 GMC Jimmy 4-wheel drive, 4.3 liter 6-cylinder is mounted in the engine block. Under the hood, look in the lower engine area on the passenger side, beneath the cylinder head.
Where can you find a wiring diagram for a 1979 GMC Jimmy?
It is important to have a diagram of the wiring system in a car. The wiring diagram for a 1979 GMC Jimmy can be found it is maintenance manual.
How do you replace ignition 93 gmc suburban?
Disconnect the battery. Remove the steering wheel. Remove turn signal switch,Remove the buzzer switch with needle nose pliers. Then insert the key(make sure it is not in place beforehand) and place in lock position. remove lock cylinder retaining torx screw. Then with key in place, pull out the assembly straight out.Disconnect the electrical connector from the bulkhead connectorand remove retaining clip. attach some wire to the connector to help with installation and pull harness through column. Installation is reverse.
Where is the slave cylinder on 1998 gmc sonoma?
Inside the transmission
Where is the starter on a 1996 gmc jimmy?
Look at the lower rear end of engine
How do you remove a lock cylinder for a 1988 gmc jimmy?
if it is the ignition lock cylinder, first disconnect the battery, you need to remove the steering wheel ,turn signal switch , etc, then you need to insert the ignition key into the lock cylinder, turn it to the run position,then pull the cylinder out, reverse the operation to install the cylinder,
How do you change the ignition switch on a 1996 GMC Yukon?
howdo you change an ignition switch on a 1996 gmc jimmy howdo you change an ignition switch on a 1996 gmc jimmy
How do you change the ignition switch on a 2004 gmc 1500 sierra truck?
how to remove cover to replace ignition lock cylinder and what type of tools do i need
How do remove the key cylinder in a 1998 gmc jimmy?
If you have the "PassLock" Security system on your vehicle, you MUST take it to the dealer to have the ignition changed out. The will have to reprogram the security system to match. If they don't your security may stay engaged which will cut of the fuel.
How do you remove radiator from gmc jimmy?
How to remove a bad radiator from a 1992 GMC jimmy 4x44-door,v6 engine?....Thank you :)
1988 gmc safari Steering column switches and ignition key lock cylinder replacement?
1988 gmc safari Steering column switches and ignition key lock cylinder replacement?
How do you remove an ignition lock on 1989 GMC Sierra?
== ==
How do you replace the ignition lock cylinder on a 1994 GMC Jimmy S-15 with tilt steering?
take the steering wheel off, remove the safety plate and there's a small screw that is about the one 'o clock position on the column. take that out. also, get a manual...ah-ha!
How do you remove the ignition lock cylinder in a 2001 GMC Savana Pickup?
On my 99 there is a small hole in the top of where you put your key in, you have to stick some thing in there and play with the ignition with the key in. I used a small hole punch i had around.
How do you check the operation of the fuel pump on a 2000 gmc jimmy?
being that fuel pump is in the gas tank I would remove the fuel line at the filter then turn on ignition being that fuel pump is in the gas tank I would remove the fuel line at the filter then turn on ignition
How many quarts of oil does a 1996 GMC Jimmy 6-cylinder hold?
5
Blower motor removal 97 gmc pickup?
Remove blower motor 97 GMC jimmy
