answersLogoWhite

0


Best Answer

If you ask a more specific question, I can help. What exactly is broken? Is it electric or power?

If it is electrical, you will need to take off the inside panel of the door. most door panels will pop in and out.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

12y ago

First you need to take off the inner door panel. First remove the plug under the door pull and then the Philips screw behind the plug. Next take the plastic trim off the door latch and remove the screw behind the cover. Last screw is under the plastic trim on the side of the door near the latch. Then remove the button clips,you will probably need a Philips screw driver and a flat to pop out the buttons mostly located along the bottom. Next pop up the top part of the door cover on the top surface of the door after you remove the lock plastic pull. Now you will need to drill out the rivets. There is one near the top of the door and 3 down near the bottom. Now lower the window to get to the clip holding the window to the regulator. There is a black clip on the bottom that can be removed by pushing the tab over with a flat blade screwdriver. After the clip is removed the plastic part will slide out of the window and the regulator can be removed. Remove the motor with 4 Torx fastners and bend out tab holding motor in. Install new regulator and secure clip to window first, then add pop rivets.

This answer is:
User Avatar

User Avatar

Wiki User

16y ago

Remove the interior panel by unscrewing door handle. The window can be wedged into the "up" position from underneath by introducing a piece of 1X3 lumber cut to the correct length and grooved across both ends. It is probably not worth while to pay for the proper repair on an old Excel.

This answer is:
User Avatar

User Avatar

Wiki User

16y ago

You need to determine if it is the switch that is bad. Trying "jumping" the switch with a 12 volt battery. By putting the positive and negative leads to the window motor one way will lower the window. By revering the polarity it will go up. If it doesnt then your motor is bad. You need to connect the wires by by-passing the switch directly to the motor. You will have to either remove the switch or remove the interior door panel in order to do this. I hope this helps you. Good luck.

This answer is:
User Avatar

User Avatar

Wiki User

9y ago

To repair a stuck driver-side manual window, use a screwdriver to remove the screws attached to the door panel. Pull the door handle away from the door and lower the window regulator to the lowest possible position.

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

how do you change out the left back door window in a 1989 Toyota corolla?

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

How to replace a motor driver side for a town and country 2002

This answer is:
User Avatar

User Avatar

Wiki User

11y ago

Driver Side Window Regulator Assembly replace on 2004 Pontiac grand prix

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

You need to buy a Haynes Manual at a parts store or a bookstore. They have them specific to your car.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you change a driverside door window with a new one?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you install a new window regulator on a mgzr drivers door?

To install a new window regulator on a MGRZ driver's door, remove the door panel and the wiring attached to the power window mechanism. Remove stereo speaker from the inside door and the window glass. Remove the old window regulator and replace with new.


How do you change the glass of a window of a car?

door glass- you have to removed interior door handle, door panel to get access to the bolts that attach the glass to the window regulator. then the glass is pulled up and out. rear window and windshield- the glass is cut out with special tools and the new glass is glued in.


How do you change the front passenger window weatherstripping on a Honda civic?

To change the front passenger window weatherstripping on a Honda Civic first open the door. Pull the old stripping off and remove the door panel. Use a water proof sealant and place the new weatherstripping around the window.


How do you install a door window on a 1963 impala?

Remove the inside door panel. Slide the new glass up through the window opening. Set the new glass in the window track.


How do you add a window to a 6 panel exterior door?

Adding a window to an exterior door is problematic. Cutting a section out of the door causes structural and plumb issues. It is better to purchase a new door with the desired window.


New beetle driver side window only rolls half way down?

There is a styro-foam sound deadening piece in the door It measures about 6in tall and 24 in long . the one on my driverside door came loose inside and would stop the window 1/2 down. STEP 1) 3 screws in bottom of door, 2 more in the handle. to remove the inner door skin. STEP 2) Unbolt inner door skin from door. STEP 3) Either RE GLUE the styro to the door or remove it completely ( Recommend that you reglue it. reverse the process and DONE .


How do you change out the front passenger window switch on 2005 equinox?

There are several steps that need to be taken to change a window switch on a 2005 Equinox. You can find detailed instructions and videos online. However, the basic plan is to first remove the interior door handle's?æbezel and the interior door handle. You will need to remove the old regulator, and install the new switch before replacing the door and door handle.


How do you install rear passenger window Tracer?

Remove the rear passenger door panel. With the door panel removed the entire window mechanism will be visible. Place the new window in the window track. Secure the window with the retaining clips.


How do you install a new drivers side window in a car?

Take the outer door panel off then unbolt the old window from the track then place the new window in the track this will take sometime because the new window has to go in at an angle before you place the new window in the track make sure the track is at the bottom of the door use your hand tp place the window all the way down in the door then bring the window all the way up holding it with one hand at the bottom of the window you need to put the window all the way to the bottom first to make sure the window clips aline in the window track. roll the bottom of the track up intill you can bolt the new window in but be careful if you tighten down the window to tight it will break the put the door panel back on


How do you change a 2002 Honda civic window lift motor?

Remove the inside door panel. Remove the wiring harness from the window motor. Remove the track linkage. Remove the window motor retaining screws. Reverse the process to install the new window motor.


How do you replace a 1975 Firebird door window?

undo the glass from the regulator and pull it up out of the door and get new gass and drop it down inside the door into the window channels and rehook the glass to the regulator.


My 1990 240sx door window will not go up but the window motor works?

you need a new belt for the motor to raise and lower the window you need a new belt for the motor to raise and lower the window