0
There are basically two types of meggers, an electronic one and the old-fashioned hand-cranked type. On the whole megger testing is non-destructive.
What happens is a DC voltage is applied to the device or winding under test. It is basically an insulation test to see if the insulation has been injured in any way to cause a short circuit when normal power is applied to it.
On some meggers there are 3 ranges 300V, 750V, and 1000 volts. Applying the proper voltage is essential to avoid damaging the device you are testing.
Working voltages up to 240 volts should use the 300 range. Working voltages up to 600 volts use the 750 volt range and working voltages above 600 use the 1000 volt range.
If you used the 1000 volt range on a device that had a working voltage of only say 24 volts, you could damage the insulation of the device just by testing it! So meggering a device is only non-destructive if you use the tester as its instructions tell you to.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 12y ago
Wiki User
∙ 12y agoOn the whole megger testing is non destructive. What happens is a DC voltage is applied to the device or winding under test. It is an insulation test to see is the insulation has been injured in any way to cause a short circuit when normal power is applied to it. On my megger there are 3 ranges 300V, 750V, and 1000 volts. Applying the proper voltage is essential to not damaging the device you are testing. Working voltages up to 240 volts should use the 300 range. Working voltages up to 600 volts use the 750 volt range and working voltages above 600 use the 1000 volt range. As you can see if you used the 1000 volt range on a device that had a working voltage of say 24 volts you could damage the insulation just by testing it. So meggering a device is non destructive if you use the tester as its instructions tell you to.
Add your answer:
Earn +20 pts
Where can one purchase an electrical tester?
One can purchase an electrical tester at Amazon. Amazon has a wide variety of these, so there are many options to choose from. Like Amazon, Fluke also sells a wide variety of electrical testers.
What value of tester is to be used for measuring insulation resistance of three phase 600V cables?
The typical test equipment for this is a megger. The megger is connected to two conductors at a time to test the insulation between the two.
What is a Megger 1552 used for?
The Megger MFT 1552 is a combined electrical circuit tester which includes test features for Insulation testing, Earth loop impedance tests, RCD Testing and Continuity testing. It comes supplies with full Calibration Certificate.
What meters are kept on HV side in SC test?
insulation tester (Megger) can used to checked the short circuit on HV side. HI POT tester is also a means to checked the shot circuit in HV cable.
Can a high voltage transformer be megged with a megger meter?
No. A megger's output voltage is not high enough to test the insulation of a high-voltage transformer if, by 'high-voltage transformer ', you mean a distribution transformer or power transformer. Instead, a high-voltage test set or 'pressure tester' (e.g. a 'HiPot' tester) must be used, as these produce far higher voltages.
How do you use earth tester - megger?
how to use electrical earth tester
What is the output voltage of an insulation tester which is required to test a 230v circuit?
On a hand crank megger which is used to test insulation breakdown, use the 300V setting. If the megger does not have that setting use 500V as opposed to 1000V for the test. The output of the megger is a DC voltage.
Can you use a 500V megger tester to test a 6.6KV motor?
You can, and you will get a reading if the leakage is within the operating parameters of the megger or there is a dead short in the windings. Most larger voltage motors need higher testing voltages. A hi-pot tester will deliver these higher voltages.
What do electricians use to test circuits?
Continuity tester, volt meter, clamp on amp meter, megger and ohm meter.
What is the meaning of OL showing in the display of megger tester?
Over Load
Can a megger tester cause injury to humans?
A megger device produces hundreds of volts in order to provide resistance values in the order of hundreds to thousands of megohm. The DC volts produced by a megger can and will harm humans.
Where can one purchase a Megger MFT1835 online?
A Megger MFT1835 electrical installation tester can be purchased online at Screwfix or Instrotech. They can also sometimes be found second hand on eBay.
Where can one purchase an electrical tester?
One can purchase an electrical tester at Amazon. Amazon has a wide variety of these, so there are many options to choose from. Like Amazon, Fluke also sells a wide variety of electrical testers.
How do you check a motor for a bad winding?
You need a Megger tester. With one lead attached to the winding and the other attached to the motor housing, the Megger sends a high voltage through the winding. The Megger reads the resistance, letting you know if there is a short to ground.
What value of tester is to be used for measuring insulation resistance of three phase 600V cables?
The typical test equipment for this is a megger. The megger is connected to two conductors at a time to test the insulation between the two.
What is a Megger 1552 used for?
The Megger MFT 1552 is a combined electrical circuit tester which includes test features for Insulation testing, Earth loop impedance tests, RCD Testing and Continuity testing. It comes supplies with full Calibration Certificate.
What meters are kept on HV side in SC test?
insulation tester (Megger) can used to checked the short circuit on HV side. HI POT tester is also a means to checked the shot circuit in HV cable.
