0
For convenience I install the receptacle just above the backboard of the dryer. This way if the dryer is to be moved out of its location it can be unplugged before the move is started. Sometimes the dryer is located in a confined space and it is hard to reach down to the floor level to unplug the dryer with out becoming an acrobat.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Should a 3 wire 250 volt drier be grounded?
Yes, most definitely. Provisions for the ground wire in the dryer receptacle should be used. The feeder cable's ground wire is first grounded to the receptacle's junction box ground screw and then taken to the receptacle's ground terminal. The dryer plug configuration will match up to the dryers four wire plug in cable. When the plug is connected into the dryer receptacle the ground terminals of both devices will match and the ground wire will be continuous from the voltage source at the distribution panel and complete the circuit at the dryer. This low impedance electrical path will conduct any ground fault that could occur at the dryer and trip the feeder breaker of the dryer circuit, there by removing the fault current from the dryer circuit.
Can you install an electrical switch before a gfci?
Yes! you can install an switch a head of a GFCI receptacle. This installation is common in some applications to turn on an outside receptacle to control Christmas lights.
How do you know if clothes dryer is hard wired?
Hard wired means that there is no plug and receptacle in the circuit powering the dryer. What you will find is a metal jacketed cable that will come out of the wall or floor and go right into the dryer.
You were shocked by a dryer receptacle is there any danger?
Yes there is a serious danger. The breaker should be tripping under this condition and not allowing the frame of the dryer to become electrically energized. It means that the ground wire is missing from the dryer receptacle or the dryer cord is not grounded to the machine. Shut the breaker off to the dryer and remove the dryer receptacle. Look for a bare copper wire. It should be bonded to the box and then to the receptacles U shaped pin hole. If this end is fine check the dryer end where the cord goes into the back of the dryer to make sure the green ground wire is connected to the frame of the dryer. If you don't feel competent of doing this get some electrical help as this condition needs to be repaired before you use the dryer again. If you were shocked and recovered, you will be OK You should report it though because it could kill someone, for example, if they had a heart problem of some kind.
Can you install a 277 volt receptacle in place of a 240 volt receptacle?
No. To prevent this sort of thing from happening, the 277 volt device and receptacle is physically larger that a 240 volt receptacle and will not fit in a regular receptacle junction box. For a 277 volt system the proper size junction boxes have to be purchased.
How do you install a lamp?
Plug it in to a receptacle.
Can I install a GFCI receptacle from an existing receptacle in the basement?
Yes, there is no reason why this can not be done. In fact a benefit of this is that every receptacle downstream from this new receptacle will also be protected by the GFCI receptacle.
Should a 3 wire 250 volt drier be grounded?
Yes, most definitely. Provisions for the ground wire in the dryer receptacle should be used. The feeder cable's ground wire is first grounded to the receptacle's junction box ground screw and then taken to the receptacle's ground terminal. The dryer plug configuration will match up to the dryers four wire plug in cable. When the plug is connected into the dryer receptacle the ground terminals of both devices will match and the ground wire will be continuous from the voltage source at the distribution panel and complete the circuit at the dryer. This low impedance electrical path will conduct any ground fault that could occur at the dryer and trip the feeder breaker of the dryer circuit, there by removing the fault current from the dryer circuit.
How do you know if clothes dryer is hard wired?
Hard wired means that there is no plug and receptacle in the circuit powering the dryer. What you will find is a metal jacketed cable that will come out of the wall or floor and go right into the dryer.
Can you install an electrical switch before a gfci?
Yes! you can install an switch a head of a GFCI receptacle. This installation is common in some applications to turn on an outside receptacle to control Christmas lights.
You were shocked by a dryer receptacle is there any danger?
Yes there is a serious danger. The breaker should be tripping under this condition and not allowing the frame of the dryer to become electrically energized. It means that the ground wire is missing from the dryer receptacle or the dryer cord is not grounded to the machine. Shut the breaker off to the dryer and remove the dryer receptacle. Look for a bare copper wire. It should be bonded to the box and then to the receptacles U shaped pin hole. If this end is fine check the dryer end where the cord goes into the back of the dryer to make sure the green ground wire is connected to the frame of the dryer. If you don't feel competent of doing this get some electrical help as this condition needs to be repaired before you use the dryer again. If you were shocked and recovered, you will be OK You should report it though because it could kill someone, for example, if they had a heart problem of some kind.
How do you install a 12v power receptacle on your motorcycle?
Run a fused power line from the receptacle to either the battery for constant Hot or to the fuse box for an ignition controlled receptacle and ground the receptacle either by mounting on a metal surface or run a ground wire from the body of the receptacle to a good chasis ground
Can you install a 277 volt receptacle in place of a 240 volt receptacle?
No. To prevent this sort of thing from happening, the 277 volt device and receptacle is physically larger that a 240 volt receptacle and will not fit in a regular receptacle junction box. For a 277 volt system the proper size junction boxes have to be purchased.
My 110 washer will work my 220 dryer will work. why will it throw breaker when both are plugged in on separate breakers?
Your 110 volt washer receptacle sounds like it is not a dedicated circuit directly fed from the distribution panel as it should be. It sounds like someone has tapped off of one side of the dryer receptacle hot and neutral terminals and run them to the receptacle for the washer. If true, this would have been done in the back side of the dryer receptacles which is located in the wall. You best get it checked out because it is likely the wire feeding the washer receptacle is a #14 rated at 15 amps and is undersized for a 30 amp breaker. A #10 wire has the capacity to be connected to a 30 amp breaker which you should find the dryer's connection to be.
Why are you reading 230v between neutral and hot on a dryer receptacle?
it is a miss-wire, check what voltage you get between ground and the other hot!
Washers and Dryers?
form_title= Washers and Dryers form_header= Wash your clothes at home when you install a washer and dryer! Do you want to install a high efficiency washer?*= () Yes () No () Not Sure What are the dimensions of your space?*= _ [50] Do you want the washer to be front load?*= () Yes () No () Not Sure What features do you want in your dryer?*= _ [100]
Is it possible to install an electrical receptacle box outside the by taping into an inside receptable?
Yes this can be done.
