0
How many amps does a 2 ton 14 SEER Trane AC draw at startup and running?
Wiki User
∙ 15y ago
The answer you are looking for is on the condensing unit tag. It`s listed as FLA or (full load amps) or RLA (running load amps). Start up amps are appx 5 to 6 times this # but this current is only drawn very briefly. Be sure to add both the compressor and fan motor amperage to get total current draw of the unit. The control power is supplied by the indoor unit so that is not a factor.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Power for a computer how many amps does it take to run a computer monitor and computer?
The power required to run a basic computer will be 1.35 amps for startup and .7 to .9 amps continuous. The power requirements to run an 17" monitor will be 3.5 amps startup and 1.5 amps continuous.
Will a 7000 starting amps and 10500 running amps run a 78 amp furnace?
In the electrical trade the only time there is a reference to start and running amps is when dealing with motors. The running amps is always lower than the starting amps. A 78 amp electric furnace will take a 100 amp service for it to operate and be within the electrical code guide lines.
How many amps does a 65 watt light bulb use?
Amps x volts = watts So, assuming you are running on 110 volt line, the answer is 65 watts/110 volts=.591 amps.
How many amps does a double 100 watt spotlight use?
I may be wrong, but I think you can calculate it by: Watts = Volts x Amps So: Amps = Watts / Volts Thus, if you're running them on a 240 volt circuit, it resolves to: A = 200 / 240 = 0.83 Amps
What size breaker should you use for a unit that draws 58 running amps?
70 amp
Power for a computer how many amps does it take to run a computer monitor and computer?
The power required to run a basic computer will be 1.35 amps for startup and .7 to .9 amps continuous. The power requirements to run an 17" monitor will be 3.5 amps startup and 1.5 amps continuous.
What amperage does a 1000 watt generator put out?
If running at 120 volts that is 8.33 ampsIf running at 120 volts that is 8.33 amps
Will a 7000 starting amps and 10500 running amps run a 78 amp furnace?
In the electrical trade the only time there is a reference to start and running amps is when dealing with motors. The running amps is always lower than the starting amps. A 78 amp electric furnace will take a 100 amp service for it to operate and be within the electrical code guide lines.
Are fuse sized for three phase motor two times the nameplate rating?
Not normally. They are sized slightly above the LRA ( locked rotor amps) or the FLA (full load amps) stated on the motor nameplate. The startup current of a motor can be 125-150% of the running load amperage. This depends on the motor, its EFF (efficiency) and the torque requirement of the load.
What is the difference between full load amps and running load amps?
Full load amps is the maximum rated amps that the motor should draw according to its nameplate rating. Running load amps is the actual amperage the motor is drawing at that point in time when the test is taken. Some motor loads vary depending on if the load is cyclic. The reading on this type of motor would be from no load amps to full load amps.
What is the foremula running amps to full load amps?
There is no formula needed, they are the same thing, just two different wordings.
What is Full Load Amps?
FLA is the nameplate amperage rating of the motor when it is running at its designed horsepower and on the motors designed voltage. 746 watts = 1 HP. The FLA of a 1 HP motor at 240 volts would be W = amps x volts, Amps = Watts/Voltage. 746/240 = 3.1 amps full load. Overload the motor and the amps go higher, motor running at no load amps are lower than FLA
How do you measre the running amps a star delta motor?
Measure the current on the incoming side of the starter.
How many amps does a 65 watt light bulb use?
Amps x volts = watts So, assuming you are running on 110 volt line, the answer is 65 watts/110 volts=.591 amps.
Size wire for running 240v 130 amps mig welder?
5 mm
How many amps does a double 100 watt spotlight use?
I may be wrong, but I think you can calculate it by: Watts = Volts x Amps So: Amps = Watts / Volts Thus, if you're running them on a 240 volt circuit, it resolves to: A = 200 / 240 = 0.83 Amps
What size breaker should you use for a unit that draws 58 running amps?
70 amp
