I use a conversion factor of 152 pcf (pounds per cubic foot) for asphalt, as a general rule of thumb. For a CY, multiply by 27, to get 4,104 pcy (pounds per cubic yard) of asphalt.
1.3
The answer is, it depends. Different types of bituminous cement concrete (asphalt hot mix) use different percentages of asphalt cement. In Virginia, base mixes use at least 4.4% asphalt, while surface mixes are up to about 6%. Liquid asphalt is a little heavier than water; it weighs about 9.4#/gallon (depending on the source and grade). Here's the math: Base mix 2000#/ton x 4.4%/9.4#/gal. = 9.36 gal/ton surface mix 2000#/ton x 6%/9.4#/gal. = 12.76 gal/ton hope this answers the question.
Density of asphalt is depending on several specifications but overall it'll be between 1,010 and 1,300 kg/m3. So this is between 0.99 and 0.77 m3/1000kg Asphaltic concrete is about 2,240 kg/m3 (0.446 m3/1000kg)
The type of product measured does not change its weight requirement; a ton of feathers and a ton of asphalt all weigh: 2,000 pounds in American and 2,240 pounds in the United Kingdom; systems of measurement.
In order to make Asphalt many ingredients are needed. The exact ingredient list varies by company but usually include Asphalt cement, crushed rock, asphalt plant, Petroleum compounds, water and mineral fillers.
The main asphalt paving product is hot mix asphalt, in which asphalt cement is used to bind a mixture of stone, sand, and gravel.
Aproximately 17.78 Sq Yds of asphalt @ 1" thick per ton. Aproximately 17.78 Sq Yds of asphalt @ 1" thick per ton.
The amount of square feet in a ton of asphalt will depend on the thickness of the asphalt. If the asphalt is three inches thick it will have to cover the area three times. The type of asphalt used is also a factor towards weight.
Most paving is about 40% asphalt. So about 40% of a cubic yard.
You have not said what substance you are using a ton of to cover the asphalt.
You needed to specify to what depth the asphalt is being laid.
$ 130.00usd per ton
250 per ton
four
This depends on many factors like the area of the pavement being covered and the thickness of the pavement. This question is very general and can have many answers. Here are some conversions to help figure out how many sq ft 1 ton of asphalt cover. 0.056 tons asphalt/ SY (1 in thick) and 9 sf/1 SY. using these conversions will yield an answer of 1 ton of asphalt (1 in thick) coverinig 160.7 sf
4
The answer is, it depends. Different types of bituminous cement concrete (asphalt hot mix) use different percentages of asphalt cement. In Virginia, base mixes use at least 4.4% asphalt, while surface mixes are up to about 6%. Liquid asphalt is a little heavier than water; it weighs about 9.4#/gallon (depending on the source and grade). Here's the math: Base mix 2000#/ton x 4.4%/9.4#/gal. = 9.36 gal/ton surface mix 2000#/ton x 6%/9.4#/gal. = 12.76 gal/ton hope this answers the question.
Asphalt installation is usually bid by the square yard, the installer will buy asphalt by the ton, and it will be delivered in a truck measured in cubic yards. Therefore, a volume/weight/area ratio is required. In short, an estimator will typically assume that one square yard of compacted asphalt laid one inch deep will weigh approximately 111 pounds.