What would you like to do?
If your computer is not switching on what is the problem?
Computer problems are anything that causes a computer not to function in the desired manner.
When i am switch on my computer then i am facing some problems atchuly its giving a beep and monitor show the msg signel cable diconnectedso willo you please specifie what is this atchul problem?
Well it would help if you write your question with punctuation and correct spelling so it could be understood better. but it sounds to me, like you havn't got your monit…er connected to your computer right or your moniter is dodgey.
This is a very broad question. Overall, anything that's made can break. Most problems are software related.
i turns it on
Hard drive problems, blown out speakers, it can froze and many other things
The answer in part b is the maximum distance any single cable could run from a switch to one computer in a switched Ethernet LAN How would you overcome the problem implied by this?
The distance is about 100 for both CAT-5e and CAT-6. One of solutions is to install replicator, another one is to use coax either thinnet (175 m) or thicknet (400 m). Also you… can use fiber optices (if you are going to use with long distances single mode fiber has to be used).
Me, I fix them be it software or hardware. If I don't know how to I learn by buying books, search the web, talk to others who know and learn more. If that's not what you want …to do then it would be good to know someone good at working on computers and ask if they can fix your problem. If they are willing then compensate them for it with the "thank you" of appreciation. If you don't know anyone then a computer repair store will have to do.
some electronic devices made that type of switch
Computer's have problems because they are made by people. People are not perfect but can work out problems to a desired result. Computers do what they are told. Even still, in… electronics there are still things that are not fully understood about electricity and how it actually works. Understanding how electronics work may be about 85 percent or higher which can give a pretty good cosistancy of funtionality. Other than that, most problems occur on PC's due to software installation weather it be wrong drivers, source code and viruses. its all software based. it not as likely that any of the hardware in the computer bust as it does take some time for these components wear down.
click on settings
well some problems computers have had were the premo scepto which is when a computer blows out its control panel inside of the computer , also there is a vinched topee which i…s when the computer explodes
All those extras you have can slow down your computer or glitich it up. Also when you are done using internet turn off your wireless card on your router or unplug your motem. …IF YOUR INTERNET IS TURNED ON ALL THE TIME THEN YOU CAN GET SPYWARE OR TROJENS OR SOMEONE CAN HACK YOUR COMPUTER. IF YOUR INTERNET IS TURNED OFF OT WON'T HAPPEN
When a computer is switched on, it begins by executing instructions stored permanently in ROM. These startup instructions do some self-testing, configuring, and device initial…ization, and is called the BIOS. The BIOS will load into memory the next set of startup instructions, called the boot loader, which is found in the startup device stored in its configuration. The boot loader in turn loads up and executes the boot instructions of some application, usually an operating system, which performs its own startup and refreshing tasks. These tasks are under the control of, and follow the rules of, that operating system. In summary, whatever is required to refresh a computer after turning it on is determined by its operating system.
What is the problem if the breaker isn't tripped and there is no power to my switch in computer room switch in foyer switch for outside porch and alarm panel is dead?
The most likely problem is that the breaker has tripped. On some breakers there is a indication window that shows a red flag if the breaker needs resetting. On other breakers …there is no indication but a slight misalignment of the breaker handle as compared to the other ones. On the distribution panel find the breaker number of the circuit that is off from the panel index. Push the breaker handle to the furthest off position that you can. As the handle is moved to the off position you will feel a bit of resistance. Push past it as that is the breaker resetting. Return the breaker to the on position to see if the circuit has re-energized. The only other reason is that a wire has become disconnected in the circuit. If you have been doing any electrical work on the circuit start looking in that area. To troubleshoot these types of problems it will require the use of a volt meter to check to see if the circuit is "hot" from the breaker out. Then it is just a matter of finding where the voltage stops and locate the problem.
Computers have many flaws and problems, with the first and most important one being the fact that they will never be able to operate at the level the human brain does. Oth…er problems includes the fact that they are machines and machines are prone to breaking down or not functioning in the way it is supposed to