0
Line voltage is understood as the voltage that the device or appliance needs to operate on. It is also referred to as the devices working voltage. Once the proper line voltage or working voltage is applied to the device it may be transformed to different voltages for different internal component circuits.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Is a Line voltage understood to be any voltage?
The Line normally refers to the live wire in a single-phase system and the three live wire of a 3-phase system. In a 3-phase system the line voltage is usually quoted as the nominal voltage, and that is the voltage between any two of the live wires. The voltage between one of the lines and neutral is 1/sqrt(3) times less.
Why is phase voltage not twice line voltage?
Line to line voltage is not the same as line to neutral voltage because line voltages are 120 degrees apart. They are related by: Line to neutral voltage * tan (120 degrees) = Line to neutral voltage * 1.73.Additional CommentFor delta-connected systems, the line voltage is the same as the phase voltage.For wye-connected systems, the line voltage is larger than the phase voltage by a factor of 1.732. The reason for this is as follows:Because any two phase voltages are displaced from each other by 120o, they must be added vectorially, not algebraically, to find the line voltage. As the above answer points out, this means that the relationship between the two is the square-root of 3, or 1.732.
Is transmission voltage a phase to phase voltage or a phase to ground voltage?
Phase to Phase voltageCorrection to the above answer:There is no such thing as a 'phase-to-phase' or 'phase-to-ground' voltage. The correct terms are 'line-to-line' (or 'line voltage') and 'line-to-ground' (or 'phase voltage'). Transmission-line voltages are line-to-line (or 'line') voltages.
What is phase voltage and line voltage in star connection?
The conductors that connect a three-phase supply to its load are called 'line conductors' or, more simply, 'lines'. The individual generator stator windings, transformer winding, or loads are called 'phases'. Lines and line terminals are identified by colours, letters, numbers, or combinations of letters and numbers. For example, A-B-C. Phases are identified by using the letters assigned to the line terminals between which the phases are connected, e.g A-B, B-C, and C-A. Voltages measured between lines ('line-to-line') are termed 'line voltages', and currents that pass through the lines are called 'line currents'. Voltages measured across a generator's windings, transformer windings, or individual loads, are called 'phase voltages', and the currents that pass through these are called 'phase currents'. For a three-phase, three-wire, system, the phase- and line-voltages are numerically-equal to each other. For a three-phase, four-wire, system, the line voltage is 1.732 times larger than the phase voltage.
What are the phase voltages if the line voltages are 100volts?
It depends on the type of three-phase system. If it's a three-wire system, then the phase voltage is numerically equal to the line voltage. If it's a four-wire system, then the phase voltage is numerically equal to the line voltage divided by 1.732 -in your example, this works out to be 5.77 V.
Line voltage is understood to be any voltage?
The Line normally refers to the live wire in a single-phase system and the three live wire of a 3-phase system. In a 3-phase system the line voltage is usually quoted as the nominal voltage, and that is the voltage between any two of the live wires. The voltage between one of the lines and neutral is 1/sqrt(3) times less.
Is a Line voltage understood to be any voltage?
The Line normally refers to the live wire in a single-phase system and the three live wire of a 3-phase system. In a 3-phase system the line voltage is usually quoted as the nominal voltage, and that is the voltage between any two of the live wires. The voltage between one of the lines and neutral is 1/sqrt(3) times less.
What is a line to line voltage?
In a 3 phase system, the voltage measured between any two phase is called line to line voltage.And the voltage measured between line to neutral is called phase to neutral (line to neutral) voltage.AnswerThere is no such thing as a 'phase-to-phase' or a 'phase-to-neutral' voltage. The correct terms are 'line-to-line' and 'line-to-neutral'.The voltage between any two line conductors is called a line voltage.In a three-phase, three-wire, system, the line voltage is numerically equal to the phase voltage.In a three-phase, four-wire, system, the voltage between any line conductor and the neutral conductor is called a phase voltage. The line voltage is 1.732 times larger than the phase voltage.
What voltage should 208 3 phase leads read?
From line-to-line (any two of the three leads) voltage or 'line voltage', the voltage is 208 V. The line-to-neutral (one of the three leads and the neutral conductor), or 'phase voltage', is 120 V.
Is line voltage or phase voltage mentioned on transformer nameplate?
It depends how they are connected. If they are connected between line conductors then they are measuring line voltages. If they are connected across phases then they are measuring phase voltages.
What is line voltage in star connection?
Phase to phase voltage is 1.732 (the square root of 3) times the phase to star point (neutral) line voltage.e.g. if the line voltage is 220Vphase voltage = 1.732x220 = 380V (approx)Additional AnswerYou might also like to know that the line voltage leads the phase voltage by 30 electrical degrees. And, incidentally, the correct expressions are 'line-to-line' not 'phase-to-phase', and 'line-to-neutral' not 'phase-to-neutral' (think about it, a line voltage is measured from the junctions between adjacent phases, so they cannot be 'phase to phase'!)
What is the difference between line voltage and phase voltage?
The three 'hot' conductors supplying electricity to a three-phase load are called LINES, not 'phases' (although unfortunately the term 'phase' is widely, but incorrectly, used in the field). Phases exist between line and neutral in star, or wye, connected systems, and between lines in a delta, or mesh, connected system. Accordingly, the term 'phase to phase' is quite meaningless. A line voltage, therefore, exists between any two lines. For a star (wye) connected system, a phase voltage exists between any line and the neutral conductor. For a delta (mesh) system, a phase voltage is exactly the same as a line voltage.
Why is phase voltage not twice line voltage?
Line to line voltage is not the same as line to neutral voltage because line voltages are 120 degrees apart. They are related by: Line to neutral voltage * tan (120 degrees) = Line to neutral voltage * 1.73.Additional CommentFor delta-connected systems, the line voltage is the same as the phase voltage.For wye-connected systems, the line voltage is larger than the phase voltage by a factor of 1.732. The reason for this is as follows:Because any two phase voltages are displaced from each other by 120o, they must be added vectorially, not algebraically, to find the line voltage. As the above answer points out, this means that the relationship between the two is the square-root of 3, or 1.732.
What is the voltage that supplies a motor starter called?
In the electrical trade it is called control voltage. This voltage can be any voltage. In North America the common control voltage is 120 volts.
Why is The voltage across the empty socket is equal to the line voltage?
all the sockets are always connected in parallel,due to this the voltage across each soket is same. when any socket is open then there is no voltage loss..so the votage is same like line voltage.
Is transmission voltage a phase to phase voltage or a phase to ground voltage?
Phase to Phase voltageCorrection to the above answer:There is no such thing as a 'phase-to-phase' or 'phase-to-ground' voltage. The correct terms are 'line-to-line' (or 'line voltage') and 'line-to-ground' (or 'phase voltage'). Transmission-line voltages are line-to-line (or 'line') voltages.
What is phase voltage and line voltage in star connection?
The conductors that connect a three-phase supply to its load are called 'line conductors' or, more simply, 'lines'. The individual generator stator windings, transformer winding, or loads are called 'phases'. Lines and line terminals are identified by colours, letters, numbers, or combinations of letters and numbers. For example, A-B-C. Phases are identified by using the letters assigned to the line terminals between which the phases are connected, e.g A-B, B-C, and C-A. Voltages measured between lines ('line-to-line') are termed 'line voltages', and currents that pass through the lines are called 'line currents'. Voltages measured across a generator's windings, transformer windings, or individual loads, are called 'phase voltages', and the currents that pass through these are called 'phase currents'. For a three-phase, three-wire, system, the phase- and line-voltages are numerically-equal to each other. For a three-phase, four-wire, system, the line voltage is 1.732 times larger than the phase voltage.
