0
You need to check the compressor sticker or plate. If faded or unreadable try the installation paperwork/instructions. Typically you can search by the model number online to find it.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Air conditioner blows circuit breaker when heating?
If you have a heat pump and the breaker blows in heat cycle then you probably also have auxiliary electric heat which is drawing too much current because of a faulty heater element.
How does an electric heat pump work?
An electric heat pump can heat up your home during winter and cool it during summer.
Can a 220 Volt well motor be added to a 200 amp box or does it need its own box?
The well pump breaker is installed in two slots in your breaker box. You then run the correct size cable for the amperage of the pump to the area where the pressure tank is located. install a breaker or disconnect on the wall near the pressure tank and then connect the low pressure switch to the disconnect. Connect the pump to the low pressure switch.
What size wire do you use to install a 40 amp breaker for a 2amp pool pump?
I think you mean 2 HP pump. I am assuming a 220 To 240 volt supply and that should equate to about a 12 amp current. All my pumps use only a 30 amp breaker and 10 AWG wire.
Why is there an electric heating coil in a heat pump?
Heat pumps don't work well when the temperature outside drops below 40 degrees Fahrenheit. The way a heat pump works is by absorbing heat from outside and moving inside using the refrigerant. Much like an air conditioner absorbs the heat from inside of your home and moves it out. Therefore the colder it is outside the less heat a heat pump can produce. The reason they install electric heat strips is to ensure that when the temperature outside gets below 40 you will still have enough heat available to heat the property.
You bought a rheem heat pump what gauge wire should you use for a 80amp breaker?
My heat pump was professionally wired when built in 2004. Wire is No. 4 AWG with 80 amp breaker
What type of circuit has double 20amp breaker going to a separate box at that separate box there is a well pump with another 20amp breaker to that?
Sounds like a 240 volt sub panel feeding a well pump.
Air conditioner blows circuit breaker when heating?
If you have a heat pump and the breaker blows in heat cycle then you probably also have auxiliary electric heat which is drawing too much current because of a faulty heater element.
Do you need a license to buy a heat pump?
I do not know of any jurisdiction in which a license would be required for a heat pump.
How do you reset the fuel pump or security breaker on a 1999 Lincoln Navigator?
The Fuel pump reset switch is located in the rear interior panel on the driver side by the tailgate. it is typically covered by a stock plastic panel. the switch is a simple push to reset switch.
Where is the fuse for the air suspension pump?
I believe it is under the passengers seat. In my 1991 there is a circuit breaker under the hood in the fuse panel. Check manual.
Why will my heat pump not start when i turn on thermostat?
First, is the thermostat in he correct position for cooling? Is there a red light glowing on the thermostat? There could have been a power surge or outage and the heat pump needs to reset. Turn the power off to the heat pump at the control panel for a couple or minutes then back on again to reset the heat pump.
Can you use a 240 volt pool pump on normal house power?
Most typical US residences have both 240 and 120 AC voltage. The pump would have to tie into a 240 volt breaker in your electric panel. To ensure safety have an electrician familiar with pool installations install the wiring and motor/pump and also make sure that the breaker is sized for the motor amperage rating. In many pool installations a separate electric panel will be installed outside near the pump and any pool electric devices.
How often is a landlord required to replace heat pump?
when its broke or u can prove its not working right
Can you straight wire a sump pump to the breaker box?
Yes. Check local electric codes to see if a disconnect is required at the sump pump. One way is to wire a single 15A circuit to an outlet for sump pump. Then the disconnect is just to unplug the pump for service.
How do you run a 120V outlet off a 240V water well breaker?
You will need to have a three wire feeding your well pump motor to do this. It will be connected like a sub panel breaker box. A new breaker for the pump out of the new panel and a 15 amp breaker for the new receptacle. Both of these circuits must be protected by their own breaker. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Is there an access panel to the fuel pump in a 1992 Saturn?
No there is no access panel to the fuel pump.
