A 35 - 40 gallon bladder tank ( which is common in a regular house ) weighs approximately 50 pounds.
What kind of tank? How much water is in it? Is there air in the tank? What fills the tank? What kind of pressure from where and what?answerIf the tank is gravity fed, multiply .431 times the altitude that the source is above the tank. For example, the reservoir supplying my domestic water system is approximately 200 feet higher than the valley floor I live on. My water pressure is slightly over 80 psi. If the tank is pump fed, and if you have no information on the pump, you will have to put a gauge on the system.
There is a certain amount of sediment in all well water - it is coming out of the ground remember. Every well should have a sediment filter before the pressure tank.
You may have an artesian well. Pipe some of it to a holding tank for periods when you need more.
the pressure depends on the well pressure tank and switch. It is normally between 30 and 70 psi in a domestic well system
Something is wrong in your pressure tank, possibly waterlogged and rusting.
50 gallons
Well that depends on what you made the bottle out of and how much of that material you used. But the water inside would weigh approximately 473 grams (roughly 1 pound) depending on certain environmental conditions
WELL, The volume of the tank is 4*3*1.5=18m3. The volume of a rectangular stone is 0.15*0.1*0.08=0.0012m3. To raise the water to the top, the volume of stones that occupy the tank must be equal to the remaining space unfilled by water. That is, Volume of stones to be dropped = Volume of Tank - Volume of water in the tank. Now the Volume of water in the tank is 0.6*4*3=7.2m3. Empty space in tank = 18 - 7.2 m3 = 10.8m3. To get the number of stones to be dropped to fill this empty volume, Number of stones = Volume of empty space / volume of a stone. = 10.8 / 0.0012 = 9000.
The tank comes with a residual air pressure of about 40 PSI. This can be regulated through the air nipple at top of tank. If you are going to use 30/50 as is common, then set tank air to 28 by adding or letting air out of this nipple while the tank is empty of water. After setting this pressure, adjust the pressure switch to come ON at 2 psi above this , ie 30 PSI. Now when the water level lowers in the bladder the pump will switch ON before the tank is empty. If tank residual pressure is very low on an old tank it is possible that your bladder has holes.
When nothing comes out.
they should I would measure really well first and be careful that the tank is empty
Water pressure makes the water run out of the faucet. This pressure is provided by the pumps in a city water system, or in the case of a home on a well, by the home pressure tank. This pressure tank is fed by the well pump and also has air pressure in it. Generally the water fills a large balloon (called a bladder) inside the tank, the pump then stops until the pressure drops (when the tank is nearly empty) In most home systems this is about 15 -20 gallons between each pump cycle.
Water pressure makes the water run out of the faucet. This pressure is provided by the pumps in a city water system, or in the case of a home on a well, by the home pressure tank. This pressure tank is fed by the well pump and also has air pressure in it. Generally the water fills a large balloon (called a bladder) inside the tank, the pump then stops until the pressure drops (when the tank is nearly empty) In most home systems this is about 15 -20 gallons between each pump cycle.
A well made modern glass aquarium can be left empty for many years provided it is cleaned before being put away safely for storage.
Water weighs a little more than 8 lbs/gallon. The tank would weigh around 150 lbs. plus gravel, decor, etc. If the dresser is well-built and the tank is stable and level on it then it should be fine.
The water is pumped for a certain time, as the water is pumped from the bottom tank to the top tank and we get our water for the day from the top tank only.
The size of tank is immaterial. ALL domestic well water pressure tanks should have 28 or 38 psi when nearly empty. The difference is whether it has a 30/50 or a 40/60 pressure switch on it.