Nothing happens. The stereo has a transformer that converts the power to DC, and 50 or 60 Hz input makes no difference.
Because its sound is collected off the strings vibration by an electrical pickup and then amplified electrically. As opposed to an acoustic which uses the sound box to amplify the strings vibration.
Needed: Phillips screw driver, FORD Din removal tool. Step 1 of 5 Disconnect the negative battery cable (or grounding cable) from the battery of the Ford Edge. The grounding cable is the black cable that connects the Ford's battery to the chassis or frame of the vehicle. Use a Phillips-head screwdriver to loosen the bolt on the cable's clamp. Remove the clamp from the battery's negative lead post. Step 2 of 5 Insert the Ford DIN removal tools into the face of the stereo. There are two holes vertically aligned on either side of the stereo's face. Step 3 of 5 Pull outward on the DIN tools (away from each other) and toward you, pulling the stereo from the dash. Step 4 of 5 Disconnect the wire groups from the rear of the stereo. The groups are for the antenna, speakers, amplifier and power supply. There also may be connections for an equalizer, a satellite radio receiver or an iPod or MP3 player. Step 5 of 5 Reconnect the grounding cable to the Ford Edge battery. Place the cable's clamp around the negative lead. Use a Phillips-head screwdriver to tighten the clamp's bolt. The clamp needs to be tightened so that it cannot be moved around the battery's lead post by hand.
YES!If you have a TV antenna amplifier rated at 12 Volts and 200 milliamps, you can use any power supply that will deliver at least 200 milliamps at 12 Volts. The important item is to keep the 12 volts at 12 volts. note: 200 milliamps is 0.2 amps. Even if you had a power supply that delivered 2000 amps at 12 volts you would be OK as it will only draw the 200ma that it needs.
Air Supply - All Out Of Love Debbie Gibson - Lost In Your Eyes Eric Clapton - I Get Lost Cindy Lauper - Time After Time Roger Waters - Lost Boys Calling Weird Al - I Lost On Jeopardy
Rural King Supply was created in 1960.
Destruction of the power supply depending on model it might affect the main board. The first thing the mains supply goes to, in an audio amplifier, is the transformer of the power supply. If you are lucky, just the mains fuse will blow, and protect everything. If you are unlucky, then the primary winding of the transformer will cook and destroy itself, needing a new transformer. If you are very unlucky, the higher voltages induced, will get passed to the main circuitry and destroy all the semi conductors.
There should be no problem but you must check it to make sure the power transformer (the heavy component inside made of iron and copper) does not get hot while operating, because it runs at a 20% higher core flux density at the lower frequency.
Yes, an amplifier can be operated on ac supply.
No change in supply voltage as additional resistance is connected in parallel circuit.
Through loda
A voltage amplifier does not have to supply significant current bur a power amplifier does.
It doesn't. You can make a differential amplifier with a single power supply.
If you are just buying speakers then they do not connect directly to a mains supply. Therefore, as long as they are connected to an amplifier with a suitable speaker output, they will work with no problem. On the other hand, if the speakers have an amplifier built in and are connected to the mains supply, they are unlikely to work on a 230V European supply if they are rated for a 110V supply. There are some exceptions to this such as multi voltage power supplies for example. If you are not 100% sure, assume that they will not work and avoid damage and personal injury.
it dosnt come on
If a DC supply is connected to the incomer of a transformer, you effectively have a short circuit, because the DC impedance of a transformer (actually, any inductor) is quite low. You will blow something.
connections are to be made per the crkt the main of this crkt is to make strong or to bost the signal comming to the crkt input is given with ac supply and they are connected to resistor and capacitor when the ac suppply is given it contains slight amount of dc supply so to block the dc supply capacitor is used and the dc supply is given at the collector so that resistor present at c and ground gets biased then another capacitor used at c to ground for removing the dc supply then out put seen on cro across collector to ground we get the perfect amplified signal the more we give the coupled amplifer the most amplfed sgnal we get
Power supply, oscillator, modulator, and amplifier.