What would you like to do?
Answer It should be on the fan shroud. If not, go to a used car lot and find a like car and trace the route there should be a diagram on the hood of your car or th…e front that tells you the route and the belt should have an auotmatic belt tightner Answer You would do best to loop it under the crankshaft, go around the water pump to the right, then loop up around the tensioner, down around the a/c compressor, and back up over the idler. then crank the tensioner and put the belt over the alternator.
It will be on the cover just over the radiator you will have the diagram for the serpentine. I do not know if Ford Taurus 1996 is the same as Ford Taurus 1994. But my 1996… serpentine routing diagram is under the hood, you may have to wipe it with a rug or towel if its dirty and hard to see. Hi, You can go to your Ford dealer and they will print one for you. Dayco has these diagrams available on-line for free. Enter all the pertinent info and it will show you the belt routing and tensioner information.
It should be on the fan shroud. If not, draw one before you remove the old one. If the belt is off, go to a used car lot and find a like car and draw one.
This should help just fine http://www.rldassociates.com/zx2/howto/belt.htm
Answer In my 1995 4.6 Thunderbird, there is a plate on the LHS wheel-well plate (in the motor compartement, near the chasis number), indication the routing of the… "drive belt"; I can make a photo if you like. Hans Westerling firstname.lastname@example.org
Answer . \nThere should be a placard with a diagram of the routing of the belt, located under the hood.
How do you replace the serpentine belt on a Ford E150 Van 1995 4.9 no AC 6cly does someone have a routing diagram?
Answer . \nThere should be a routing diagram under the hood. If not, take a digital picture of it before removal. Pry the idler pulley back and the belt slips right off.
I just gave this info for a1995 Aerostar but the information should be the same for your 1993 also. What ever search engine you use, type in www.autozone.com/repair_info. N…ow you see a page of search results, on the one showing AutoZone.com | Repair Info click on it. Now on the left side of the Auto Zone screen, find Vehicle Repair Guides and click on it. Now select vehicle year and click on it. Click on Ford. Click on Aerostar 2 WD or 4 WD. Click on 3.0 or 4.0. Now it shows Repair Guide so click on General Information & Maintenance. On right side of screen click on Routine Maintenance & Tune Up. You should now see a list of different items including Belts, click on it. Scroll down to see Removal and Installation now look for your motor, click on it. You should find all the routings you need for the serpentine belt.
Answer . Check under the hood for a black and white sticker. Should be labelled serpentine belt routing.
Hello. There are actually three possible sources for the serpentine belt routing. First of all there is usually a diagram under the hood. Second, there is usually a diagram in… the owner manual. And finally, go to a NAPA store and ask as they have all of these diagrams. Regards, JustAskJoe1234@aol.com
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?partName=Engine+Mechanical&pageId=0996b43f802e6c54&partId=0996b43f802e6c54 If that doesnt work…, go to autozone.com and put in the year, make, model of the vehicle. Under 'Repair' at the top, go to 'Repair Guides', Engine Mechanical and there is is...
I cant help you with a 1995, but when I was looking for a 1994 routing, I found a 1998 diagram of the escort serpentine belt. I found it on about.com under auto repair. … http://autorepair.about.com/cs/generalinfo/l/bl_img_ford004.htm There is the link. Good Luck. Hope this can help!!!
Answer A bad pulley (sharp edge) A seized pulley A misaligned pulley
I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine There should be a sticker near ra…diator shroud that has belt routing. If not stick the belt down past the right side of fan/water pump .put belt on crank pulley then pull back of belt over water pump and then down around power steering pulley and up over compressor pulley. put belt from crank pulley around smog pulley then up to tensioner with back of belt around tensioner and then around alternator pulley.next put rachet and socket(15 mm) on tensioner and pull on it while placing belt under idler pulley.
In Ford F-150
Serpentine Belt Under the hood should be a diagram of the belt, this is your best reference without the service manual. All you have to determine is which direction to rotate …the belt tensioner, and then put the belt back on as shown in the diagram. If it is not you can run down to your nearest auto parts store and they can print it out for you or just buy the Hayes or chilton manual on your car. It only cost a few bucks and it well helps you out later down the line if something else brakes. Relieve Serpentine Belt Tension. Before removing the belt, note its routing around all applicable pulleys for ease of installation. 1. Using a box end wrench on the tensioner pulley center bolt, rotate the tensioner assembly clockwise. 2. While holding the tensioner in this position, remove the alternator drive belt from one or two of the applicable pulleys. Use a box end wrench to rotate the tensioner pulley assembly clockwise to relieve serpentine belt tension 1. Slowly release the tensioner, and remove the box end wrench from the center bolt. 2. Remove the alternator drive belt from the remaining applicable pulleys. To install: When installing the drive belt on the pulleys, ensure that it is properly seated in all of the pulley grooves. 1. Using the box end wrench, rotate the tensioner clockwise again, then position the drive belt on all of the pulleys. 2. Slowly release the tensioner until it eliminates all drive belt slack. 3. Inspect the tensioner indicator to be sure that the belt is properly tensioned. If the belt tension is incorrect, the belt should be replaced with a new one, or, if installing a new belt, the belt may not be the correct belt for your vehicle. 4. Then start the engine. Ensure that the drive belt works properly.Stop the engine, then double-check to ensure that the belt is properly seated on all applicable pulleys.
I need the routing for the serpentine belt for 1990 Ford 150?