0
What is the formula used to determine working pressure of pipe?
Wiki User
∙ 13y ago
Equation: P = (2*S*T)/((O.D.-2*T)*SF)Where:P = Fluid Pressure (psi)
T = Pipe Wall Thickness (in)O.D. = Pipe Outside Diameter (in)SF = Safety factor (General Calculations 1.5 - 10, Use 1 For Bursting Pressure)S = Material Strength (psi)Ultimate Tensile strength or Yield strength can be used.
Ultimate should be used to determine the bursting pressure.
Yield can be used for estimating pressures at which permanent deformation begins.
1Mpa=144.55psi
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What was the purpose of hydrostatic test?
for ex; design pressure in pipe 100bar,and what is test pressure in pipe
What is the pipe leterall formola?
a formula is an equation, rule, principle, or other logical relation. The pipe lateral formula is Ao equals external pipe surface area (feet 2 per feet pipe).
What is the formula to layout pipe miters?
There is no exact formula to lay out pipe miters, but there is information that must be known to calculate the layout. This includes the diameter, wall thickness, angle, and offset.
How do you calculate volume of water in a pipe?
measure the radius of the pipe. (half the diameter - the width of the pipe) then measure the length of the pipe. then use the formula pi (3.14) x radius2 x length. the answer is the volume in the pipe
What is the formula for figuring out how many gallons of water are in a pipe by the foot?
0.61 * d2 Where d is the diameter of the pipe in inches.
What is pipe working pressure to bursting pressure safety factor?
20%
What is pipelining explain its working in detail?
pipe line is the processing of pipe line in which contain the formula
What is max working pressure of ERW pipe?
Depends on pressure and temp end connection ect>
Design a 66 inches dia buried pipe with working pressure 76 psi?
The pressure is important but so is the substance which the pipe is to carry. Is the substance carried at 76 psi or is that the external pressure
How do you determine flow rate by pipe size?
By knowing the availabe pressure and the diameter / material of the piping
Formula to calculate the wall thickness for pipe?
t = PxDxA/2E where, t = thickness P = pressure D = pipe Diameter A = factor of safety E = tensile strength of pipe
What is the working pressure for red brass schedule 80 threaded pipe?
That would depend on the temperature "Temperature pressure relationship" and the fittings used
What is the difference between Restriction Orifice and Flow orifice or please explain the symbols RO Restriction orifice and FO Flow Orifice?
A restriction orifice (RO) is used to limit the flow through the pipe to a set flow by choking the flow at its sonic velocity. A flow orifice (FO) is usually used to determine the flow through the pipe from the pressure drop over the plate. There a normally two pressure taps (one on each side of the plate) and a pressure transmitter which determines the pressure drop over the plate. A formula is then used to convert this pressure drop to a flowrate for the specific fluid passing through the orifice. A FO usually has a temperature element to determine the gas temperature for use is the formula.
What is the maximum pressure schedule 40 galvanized pipe can take?
Need to know the pipe diameter. 3 inch is the diameter of the galvanized pipe what is the working pressure of the pipe
Maximum working pressure sched 40 steel pipe?
A pressure rating refers to the qualified operating pressure which is recommended for a component or a system by the manufacturer. The maximum working pressure of a 12" steel having a schedule of 40 at 100 degrees Fahrenheit is 855 psig.
What is formula for pressure at known water flow and pipe diameter?
There isn't one. Pressure in a piping system will be determined by the pump, or head of water if it is a gravity feed system.
What is the pressure rating of XXH pipe?
Its d schedule rating of pressure of pipe...
