What is the serpentine belt routing path of a Ford F-150 6 cylinder with ac and 2wd 2000 model?
The following link will get you the serpentine belt routing path for most all vehicles. Diagram 8-1 is the one for the 2000 Ford F-150 with A/C and 8 pulleys. http://www.daycoproducts.com/daycoweb.nsf/DaycoSerpentineBeltGuide.pdf Hope this helps!
5 people found this useful
The tensioning pulley is the one just above the ac pulley 13mm wrench, pull it backwards. more help at this site http://www.rldassociates.com/zx2/howto/belt.htm hope it helps, michael tips: lace all lupes through pullies except last one, I went underneath vehicle to have space to use common …wrench to manipulate tensioner. That way it only takes one person to put belt on. My car had no belt diagram on vehicle and repair books for my year don't show diagram. Used this free website to obtain belt diagram...http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008d82b I had to search a while to get free diagram... . For the mechanics answering these questions, do the research to help your fellow man... (MORE)
If no sticker is available, contact goodyear and request a serpentine belt book or a timing belt book if that is not possible get a copy of installtions instructions from alldata services Michelle ondemand. Under the hood. My hood was replaced and repainted, no new sticker was added -you …can find this in the repair manual which you can get at your local library, at your parts store, or printout from the dealership.... just go to the parts counter and ask them to print the screen that shows it.... no charge. (MORE)
Replacing the serpentine belt on a 1996 Ford Contour 4-cylinder with AC do you need to remove anything from the car to reach the tensioner?
Answer . I just replaced the serpentine belt on my 1996 Ford Contour. I opted to remove the front passenger-side tire to gain access to the tensioner. Once I was able to get to the tensioner pulley, I had the old belt off and replaced within 10 minutes. I did have some help, though. It is much ea…sier to have one person release the tension while another puts the new belt into place. . 22:42, 14 Mar 2009 ~ . No, you do not have to remove it. It is also possible to release the tensioner top-side. I once had a tensioner go bad in the parking lot at work and had to replace it there with what I had in my trunk. It is easier with the tire off, but if you have to a slim ratchet with a shallow socket should do the trick. (MORE)
Answer . It should be on the fan shroud. If not, go to a used car lot and find a like car and trace the route. there should be a diagram on the hood of your car or the front that tells you the route and the belt should have an auotmatic belt tightner. Answer . You would do best to loop it un…der the crankshaft, go around the water pump to the right, then loop up around the tensioner, down around the a/c compressor, and back up over the idler. then crank the tensioner and put the belt over the alternator. (MORE)
It will be on the cover just over the radiator you will have thediagram for the serpentine. I do not know if Ford Taurus 1996 isthe same as Ford Taurus 1994. But my 1996 serpentine routingdiagram is under the hood, you may have to wipe it with a rug ortowel if its dirty and hard to see. Hi, You can… go to your Ford dealer and they will print one for you.Dayco has these diagrams available on-line forfree. Enter all the pertinent info and it will show youthe belt routing and tensioner information. (MORE)
he tensioner keeps the right amount of tension on the belt. If it is lose, the tensioner needs replaced.
It should be on the fan shroud. If not, draw one before you remove the old one. If the belt is off, go to a used car lot and find a like car and draw one.
My serpentine belt slipped off. I have a 2003 Hyundai sonata. I need instructions on how to put it back on.
Answer . In my 1995 4.6 Thunderbird, there is a plate on the LHS wheel-well plate (in the motor compartement, near the chasis number), indication the routing of the "drive belt"; I can make a photo if you like.\n. \nHans Westerling\email@example.com
Answer . \nThere should be a placard with a diagram of the routing of the belt, located under the hood.
Answer . \nI just did one today for my uncles 2000 Leganza 2.2. The trick is that the belt goes around the tensioner then the crankshaft pulley. It should make an s from the bottom of the alt. pulley to the tensioner then to the crank.
MORE INFORMATION NEEDED What type of engine do you have? Number of cylinders, and Liters? 1998 ford e 150 van 8 cylinder 4.6l need to find out the serpentine belt configuration
Answer . \nIt should be on left(driver) side of the frame well in front of the gas tank. It will be under pressure. I've heard some say to open the gas cap and let it sit for 30 minutes or so to let some of the pressure equalize. The filter has quick clip safety connectors at each end. Clean off …both ends so no crud gets in open lines. Remove the safety clips and pull off hoses. have rags and/or bucket to catch any gas coming out(it will drian some, but not that much) Put new one and reverse the process. Start and look for leaks. (MORE)
Answer . \ncheck under the hood on the radiator brackets or on the intake box
They are spring loaded and self adjusting. If it isn't adjusting itself, it's probably bad.
How do you change the serpentine belt on a 2001 Ford Ranger 6 cylinder and is there a square socket hole on the belt tensioner for using a ratchet handle?
the best way is use a breaker bar & cheater pipe & loosen tensioner remove belt be careful spring loaded go the same way to reinstall
Where can you find the diagram of the routing of a serpentine belt for a 1996 Pontiac grand am 6 cylinder engine with air conditioning unit?
Where to find Routing Diagrams for FREE . \nIf you do not have a routing (belt) diagram under your hood for some reason or other . Just go to any auto parts store and ask for a copy of routing diagrams\nfrom either their Gates Serpentine books or whoever supplies them with their serpentine belts …. But they DO have that information . You will have to know how many pulleys your vehicle has though,so draw out your pulley position on a piece of paper! THIS IS A MUST in order to get the right route. (MORE)
How do you check the ac compressor on a ford zx2 2000 the ac clutch pulley is bent from serpentine belt breaking?
Answer . \nThe A/C compresor is low on the front of the engine, up inside the engine\ncompartment. I have never heard of a serpentine blt "bending" a pulley...\nWhen an idler pulley bearing fails and siezes, it will break a belt. This\nis most likely the cause of belt failure. If the A/C comp…ressor drive is\nnot turning by hand, this is most likely the cause. There is a bearing\non the nose of the compressor that allows the hub to rotate and "drive" \nthe compressor when the clutch is activated. The A/C clutch is replaceable\nwithout replacing the entire compressor assembly.\nCheck all the pulleys and make sure another one is not also failed. (MORE)
Answer . \nLook under the hood in the area around the radiator support and there should be a diagram for you. Or you may want to invest in a manual from the part store.
\n. \n Awaiting more info. \n. \n. \nLet me know the engine size (in litre displacement i.e. 4.3, 5.0, 5.7, 7.4, or Diesel) and the A/C situation (exists/not) and I'll answer this one. It will save us from going over multiple combinations.\n. \nAlso, and very important; do you have Californi…a emissions. If you have the A.I.R. air injector reactor (Cali emissions). It will be at the 9:30 to 10:00 position as you face the engine from the bumper and have a very large "wheel/pulley."\n. \nOn hold,\nAtis (MORE)
Where can you find a diagram to change the serpentine belt on a 1998 Ford Escort ZX2 6-cylinder 2.0?
Answer . \nNumber one. The ZX2 only has a 4 cyl, which is the 2.0. Number 2, Go to www.zx2racing.com, there will be detailed instructions. On the left hand collum, click Pully Diagram.
How do you replace the serpentine belt on a Ford E150 Van 1995 4.9 no AC 6cly does someone have a routing diagram?
Answer . \nThere should be a routing diagram under the hood. If not, take a digital picture of it before removal. Pry the idler pulley back and the belt slips right off.
What is the serpentine belt routing for 1998 Jeep Wrangler 6-cyl with AC and power steering if the routing sticker under the hood is missing?
\nPinch the belt into a loop, pass "the loop" down the right side of the fan & slip it onto the crank pulley,pass the "non-ribbed" side over the water pump, then left onto the alternator, then up onto the A/C, then down under the idler pully, & over to the power-steering pump and finally the "non-ri…bbed" side down to the adjustable idler pulley that sits below the Power steering pump. (MORE)
What size serpentine belt is used when you bypass the AC pulley in a 1992 Oldsmobile Cutlass Ciera 6 cylinder?
Answer . They sell a bypass pulley but this is difficult to change. (you have to pull the compressor to get to the three bolts) The original belt is a 1073k6. The 1073 mean 107.3 inches. The belt needed to just bypass the compressor is 34 inches shorter, but they do not sell a 733k6 belt. They do s…ell a 735k6. This will work fine if your tensioner is in good shape. But the bypass pulleys are cheap and keep the right set up. Good luck. On my 1992 Ciera, they even had a diagram as to how the belt is installed "with AC" and "no AC" and the picture eliminated the compressor for the no AC option. If the manufacture shows an option without a compressor, I wonder why all the part stores don't have that info. (MORE)
I just gave this info for a1995 Aerostar but the information should be the same for your 1993 also. What ever search engine you use, type in www.autozone.com/repair_info. Now you see a page of search results, on the one showing AutoZone.com | Repair Info click on it. Now on the left side of the… Auto Zone screen, find Vehicle Repair Guides and click on it. Now select vehicle year and click on it. Click on Ford. Click on Aerostar 2 WD or 4 WD. Click on 3.0 or 4.0. Now it shows Repair Guide so click on General Information & Maintenance. On right side of screen click on Routine Maintenance & Tune Up. You should now see a list of different items including Belts, click on it. Scroll down to see Removal and Installation now look for your motor, click on it. You should find all the routings you need for the serpentine belt. (MORE)
Answer . Check under the hood for a black and white sticker. Should be labelled serpentine belt routing.
Hello. There are actually three possible sources for the serpentine belt routing. First of all there is usually a diagram under the hood. Second, there is usually a diagram in the owner manual. And finally, go to a NAPA store and ask as they have all of these diagrams. Regards, JustAskJoe1234@aol.c…om (MORE)
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?partName=Engine+Mechanical&pageId=0996b43f802e6c54&partId=0996b43f802e6c54 If that doesnt work, go to autozone.com and put in the year, make, model of the vehicle. Under 'Repair' at the top, go to 'Repair Guides', Engi…ne Mechanical and there is is... (MORE)
Where can i find a schematic for the serpentine belt on a 2000 ford focus 2.0l sohc motor without ac?
You can find a schematic for the serpentine belt on a 2000 FordFocus 2.0L SOHC motor without A/C in the owner's manual. You canalso check with local auto part stores.
yoh can cut it of but you have to take the cover of and go one pully at a time
I cant help you with a 1995, but when I was looking for a 1994 routing, I found a 1998 diagram of the escort serpentine belt. I found it on about.com under auto repair.. http://autorepair.about.com/cs/generalinfo/l/bl_img_ford004.htm. There is the link. Good Luck. Hope this can help!!!
Danged Belts! . Questions about belts are probably the most asked in this forum, along with questions about fuel filters/pumps and thermostats. If you peruse the answered questions, you'll find a dozen or more involving belts! Here's the consensus; Look around under the hood for a factor…y sticker which shows the routing. If it's still there, good. It's a great reference. If the belt is still on the car, make a sketch of the routing before changing it. If the belt has broken and you have no sticker showing the routing, you're hosed! Your car will never run again. Well, not really, but it complicates matters. Some folks, including me, have found diagrams online, but it seems that the belt routing varies from year to year and is dependent on which engine you have. You can't necessarily trust the diagrams you find hither and yon. The Haynes manual is invaluable, but lets us down on belt routing. There is no singular good diagram. If you have a broken belt and no diagram, you have a compounded problem. You need to find the correct replacement AND the proper routing. You could try dropping in to your local dealership and asking them for a part number. That will (probably) get you the right belt. They might be able to get you a routing diagram too. If you have the remnants of the old belt, it might have a number printed on it which a parts house can translate to a replacement. Or, they might be able to measure it and compare it to what's in their computer. I've learned a few lessons about belts. If you still have one on the car, but no routing sticker, make a sketch NOW and keep it in the glove box. If you can see a number on the belt that's currently on the car, write it down and keep it in the glove box. If you're buying a new, but unknown belt, be prepared. Know the year of your car, the size of the engine and if you have AC or not. This is what the parts counter guy will need to know to hopefully find you the right belt. While you're in the parts house, buy a Haynes or Chilton manual for your car. You'll need to check out the procedure for changing your belt. Hope this helps. If you still have problems, come back and drop us a line. We'll try again. FriPilot (MORE)
most vehicles have the belt routing under the hood if this is no longer available some auto part stores have a manual [book] that will show this
Your starter should be ( if your looking at the front of the truck) on the bottom of the truck on the left of the exhaust. you can also follow the battery cables to the starter. if is a cylinder the size of a pro -football.
Mine is the same as the same as the stock 95 5.0 Mustang GT in this photo, except that the Power Steering and AC positions are switched. http://www.allfordmustangs.com/forums/attachments/94-95-tech/74433d1248022956-1995-ford-mustang-gt-5-0-engine-f-i-drive-belt-ac-problems-94-95_mustang_belt_rout…ing.jpg (MORE)
Watch how the old one comes off. Also there should be a diagram under the hood somewhere. Check on the fan shroud. Might also be off to one side. My 89 had a sticker diagram right on the lip when you opened the hood near the latch
Check the spark plug, looking at the tip. The color and build upwill help show if you are getting proper spark. Engine compressioncould be down as well, check the compression.
You can see the serpentine belt diagram from the 2000 Ford Focusonline at places like Focus Fanatics. You can also find thisdiagram at Go Parts.
I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine There should be a sticker near radiator shroud that has belt routing. If not stick the belt down past the right side of fan/water pump .put belt on crank pul…ley then pull back of belt over water pump and then down around power steering pulley and up over compressor pulley. put belt from crank pulley around smog pulley then up to tensioner with back of belt around tensioner and then around alternator pulley.next put rachet and socket(15 mm) on tensioner and pull on it while placing belt under idler pulley. (MORE)
Put a wrench on the idler pulley and turn cw .. On my 99 e150 there is a decal/picture near the top of the radiator that shows how the belt runs. Maybe the dealer sells these decals or it is in a manual or try this page: https://www.fleet.ford.com/maintenance/owners_manuals/default.asp
Go to Auto Zone and ask them for the belt for your particular model WITHOUT ac. You MAY have to move, or remove, the compressor, but I don't think so.
Serpentine Belt Under the hood should be a diagram of the belt, this is your best reference without the service manual. All you have to determine is which direction to rotate the belt tensioner, and then put the belt back on as shown in the diagram. If it is not you can run down to your nearest aut…o parts store and they can print it out for you or just buy the Hayes or chilton manual on your car. It only cost a few bucks and it well helps you out later down the line if something else brakes.. Relieve S erpentine Belt T ension . Before removing the belt, note its routing around all applicable pulleys for ease of installation. 1. Using a box end wrench on the tensioner pulley center bolt, rotate the tensioner assembly clockwise. 2. While holding the tensioner in this position, remove the alternator drive belt from one or two of the applicable pulleys. Use a box end wrench to rotate the tensioner pulley assembly clockwise to relieve serpentine belt tension 1. Slowly release the tensioner, and remove the box end wrench from the center bolt. 2. Remove the alternator drive belt from the remaining applicable pulleys. To install: When installing the drive belt on the pulleys, ensure that it is properly seated in all of the pulley grooves. 1. Using the box end wrench, rotate the tensioner clockwise again, then position the drive belt on all of the pulleys. 2. Slowly release the tensioner until it eliminates all drive belt slack. 3. Inspect the tensioner indicator to be sure that the belt is properly tensioned. If the belt tension is incorrect, the belt should be replaced with a new one, or, if installing a new belt, the belt may not be the correct belt for your vehicle. 4. Then start the engine. Ensure that the drive belt works properly. 5. Stop the engine, then double-check to ensure that the belt is properly seated on all applicable pulleys. (MORE)
Serpentine Belt Under the hood should be a diagram of the belt, this is your best reference without the service manual. All you have to determine is which direction to rotate the belt tensioner, and then put the belt back on as shown in the diagram. If it is not you can run down to your nearest aut…o parts store and they can print it out for you or just buy the Hayes or chilton manual on your car. It only cost a few bucks and it well helps you out later down the line if something else brakes.. Relieve S erpentine Belt T ension . Before removing the belt, note its routing around all applicable pulleys for ease of installation. 1. Using a box end wrench on the tensioner pulley center bolt, rotate the tensioner assembly clockwise. 2. While holding the tensioner in this position, remove the alternator drive belt from one or two of the applicable pulleys. Use a box end wrench to rotate the tensioner pulley assembly clockwise to relieve serpentine belt tension 1. Slowly release the tensioner, and remove the box end wrench from the center bolt. 2. Remove the alternator drive belt from the remaining applicable pulleys. To install: When installing the drive belt on the pulleys, ensure that it is properly seated in all of the pulley grooves. 1. Using the box end wrench, rotate the tensioner clockwise again, then position the drive belt on all of the pulleys. 2. Slowly release the tensioner until it eliminates all drive belt slack. 3. Inspect the tensioner indicator to be sure that the belt is properly tensioned. If the belt tension is incorrect, the belt should be replaced with a new one, or, if installing a new belt, the belt may not be the correct belt for your vehicle. 4. Then start the engine. Ensure that the drive belt works properly. . Stop the engine, then double-check to ensure that the belt is properly seated on all applicable pulleys. (MORE)
you will need a 3/8 breaker bar or ratchet and a 3/4 in socket ues that to turn the tensioner to the right ( tward the driver side) to release the tension and while loose slip the belt off one of the pullies to remove
For the 1999 Jeep Grand Cherokee Laredo, you'll need a 1/2" socket wrench. The longer the wrench the better, i.e. a long breaker bar. The spring retention arm has a square hole for the 1/2" socket to be placed. Once placed, you can adjust tension for serpentine belt removal or application. Follow th…e belt route guide on the "little sticker" near the belt under the hood. If you don't have a 1/2" socket wrench, I'm pretty sure you can rent the necessary tool at Autozone for free (deposit returned when tool returned). This method works for many different vehicles, makes, and models. (MORE)
Serpentine Belt Under the hood should be a diagram of the belt, this is your best reference without the service manual. All you have to determine is which direction to rotate the belt tensioner, and then put the belt back on as shown in the diagram. If it is not you can run down to your nearest a…uto parts store and they can print it out for you or just buy the Hayes or chilton manual on your car. It only cost a few bucks and it well helps you out later down the line if something else brakes.. (MORE)
Almost impossible without a lot of work. Just get rid of the squeak by spraying all belts and pullies with belt dressing.
On a 2000 Ford F-150 : With engine oil filter change the 4.2 liter V6 engine takes : ( 6.0 U.S. quarts / 5.7 litres of engine oil ) According to the owners manual
On a 2000 Ford F-150 : For the 4.2 liter V6 engine firewall 3 - 6 2 - 5 1 - 4 front of vehicle ---------------------------------------------- For the 4.6 and 5.4 liter V8 engines firewall 4 - 8 3 - 7 2 - 6 1 - 5 front of vehicle
from a 1992 what please? in regards to your serpentine, the engine should, if your lucky have a diagram of how it goes.