It is carried out by tap-changing on the HV side of the transformer. The number of turns on the winding is increased or decreased by a number of turns to make the secoondary voltage take the right value.
Tap-changing is done on the HV side because each turn is a smaller percentage of the voltage, which permits finer adjustment.
Current transformer and voltage transformer . This transformers are actually measuring instruments which measures the quantity of current and voltage coming out of the substation.
voltage
132kV substation is part of transmission and distribution of power in which the transmission voltage is 132kV. The substation is for stepping down or stepping up of the voltages to the required voltage. the substation also serves as a place where the transmission lines can be isolated, controlled and monitored. The substation consists of different equipment that is used to regulate, monitor and distribute the required power.Another AnswerIn the UK, 132 kV voltages are considered to be the lowest transmission voltages. Other transmission voltages are 275 kV and 400 kV. A '132-kV substation' is normally one in which this voltage is stepped down to a primary distribution voltage, usually 33 kV but, sometimes, 66 kV. As the previous answer points out, substations contain transformers, switchgear, busbars, and protection equipment.
A substation is not a load but is a place where switching and voltage-level changing takes place. Accordingly, you cannot apply a 'power factor' to a substation.
An injection substation is a substation where a higher voltage is stepped down to a lower voltage,especially for transmission in a densely populated area.The transformer involved is often in the MVA range,so that the output can serve a wide area,or large consumers. In Nigeria,the common injection stations are: 15MVA or 7.5MVA 33/11kv injection substations. An injection substation is a substation where a higher voltage is stepped down to a lower voltage,especially for transmission in a densely populated area.The transformer involved is often in the MVA range,so that the output can serve a wide area,or large consumers. In Nigeria,the common injection stations are: 15MVA or 7.5MVA 33/11kv injection substations.
three phases
Current transformer and voltage transformer . This transformers are actually measuring instruments which measures the quantity of current and voltage coming out of the substation.
A substation that is smaller than the average substation. A substation converts electric power from one voltage to another.
The substation is there to convert a high voltage to a lower voltage for electricity supply. Transformers are needed to do this.
Extra High Voltage substation. It generally 132 kv or higher
The noun substation has one meaning - subsidiary station.It is a location where electricity is transformed or stepped down to lower voltage for distribution on intermediate voltage trunks.
Capacitive voltage transformer (CVT) which is having special properties & used for protection & metering purpose.
voltage
Many substation transformers have three windings - the primary, secondary, and tertiary. The tertiary bus is the bus connected to the tertiary of the transformer. this is often used as station power for the substation, since the tertiary is very often a distribution level voltage (2 - 15kV).
132kV substation is part of transmission and distribution of power in which the transmission voltage is 132kV. The substation is for stepping down or stepping up of the voltages to the required voltage. the substation also serves as a place where the transmission lines can be isolated, controlled and monitored. The substation consists of different equipment that is used to regulate, monitor and distribute the required power.Another AnswerIn the UK, 132 kV voltages are considered to be the lowest transmission voltages. Other transmission voltages are 275 kV and 400 kV. A '132-kV substation' is normally one in which this voltage is stepped down to a primary distribution voltage, usually 33 kV but, sometimes, 66 kV. As the previous answer points out, substations contain transformers, switchgear, busbars, and protection equipment.
In my line of work that is an Electrical High Voltage substation that is brand new. It is being built from a green field into an energized fully functional substation yard. There is no existing substation or remodeling of an existing one being done.
A substation is not a load but is a place where switching and voltage-level changing takes place. Accordingly, you cannot apply a 'power factor' to a substation.