0
When you drill a hole in a wall how much work do you do with the drill?
Wiki User
∙ 6y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How much work is done by a force of 500N on a stationary brick wall?
none. work is only done when energy is exchanged
A force of 10000 N is applied to a stationary wall How much work is performed?
W=(10,000N)(Om)
How do pin hole cameras work?
THEY DONT!!!!!
Is pushing up against a wall doing work?
No,beacuse the wall is oushing against you. For work to be done, it has to be done in the same direction.
How does a foghorn work?
it works by sniffing inside the little hole !
What kind of bit should be used to drill a hole through a stucco wall?
A Masonry bit will work.
In Pokemon pearl how do you do work for the old man to get a secret base?
The man in Eterna City will give you a Digger Drill and an Explorer Kit. Use the Explorer Kit to go underground, and find a place where you wnat your base. Face the wall ,press X to open the menu, select the "traps" item, and select the Digger Drill. You will drill a hole in the wall, and you can enter it, and make the base your own. :)
How can you drill a hole in a china plate?
Very slowly with a Carbide drill bit or Diamond core bit, both will work, but the diamond core bit works much better, make sure the bit has a constant flow of coolant or be submerged in the coolant. (go very slowly, do not apply much pressure, let the bit do the cutting) The best way is to use a drill press but a hand drill will work.
Do doctors sometimes drill a hole in the kneecap to releave swelling during arthroscopic surgery?
Oftentimes the orthopedic surgeon will drill a hole in the knee cap to alleviate swelling. This hole is often used to insert instruments and work internally on the knee as well.
How do you install handrails in tile?
Hold your ADA handrail where you want it. Pencil mark your hole pattern. They make drill bits to drill tile. I find the massonary style bit to work best. Dip the bit in water every once in a while to keep it cool. Drill a 1/4 " hole at each mark, tap in a blue "moly" in your FOUR locations. (use the 4 hole pattern) and screw your rail to the wall. ADA height is 34" to the center of the pipe. GL
Which bit is specifically used to drill holes in concrete and masonry work?
A 40mm hole saw is more efficient than a drill bit for holes of this size.
Do stx lacrosse heads work on warrior shafts?
yes they do but usually you need to drill a new hole
What size drill bit do i use for a one quarter inch bolt?
If you want the bolt to slide through the hole a 5/16 hole will work well.
Which drill bit would you use to cut a 40 mm hole in concrete block?
A 40mm masonite drill bit could work using the right drill. But consider using a coring machine instead because its concrete.
I am attaching wood beams for a porch and cannot find a drill bit to work How do you drill into cement?
To drill into cement you require a masonary bit for your drill. Masonary bits can be bought at any local hardware store or such like. Drill into cement using masonary bit (protects your drill from damage) then push a wall plug into the hole. to secure position and any attachment you wish to add ie woodern beams. I learnt the hard way about following this proceedure being a female that had never changed a plug.It's also helpful to have a hammer drill. They make a lot of noise, they drill into concrete much faster than a normal drill.ANS 2 - You will save yourself a lot of time and hard work by renting a good hammer drill like a small Hilti or a medium sized Bosch. You can also find many ways of attaching screws into concrete at the Hilti store. 'HIT' screws in particular , save a lot of time. They combine the screw with a polypropylene shield. You hammer drill the hole and just pound one in -simple.
What is the best way to hang a heavy picture on a wall with no stud behind it?
If the wall is made of drywall/sheetrock/gypsum wallboard, use one or more screw anchors. This is a plastic cone that comes with a screw. You drill a hole, push in the plastic cone, and use a screw driver to thread the screw into the anchor. Typically the instructions are on the package of screw anchors. Larger anchors will hold more weight, but the size of screw anchor you can use is limited by the thickness of the drywall, so the thickness of the drywall limits the weight it will support. It might be possible to use multiple anchors, but that might require some calculation and planning. If the wall is not drywall but plaster and lathe, you can use a lag bolt. This is a long threaded rod with a spring-loaded folding wing-like thing that threads on the end. To use it you drill a hole large enough to accommodate the folded wing. Push it through the hole, and the wings expand and grip the inside of the wall. Turn the screw to pull it up tight. For a brick or stone wall, there are special masonry drill bits to drill a hole, and anchors of plastic or metal that go in the hole. These expand to grip the wall when a matching screw is driven in. If the wall is not too thick, you could use a lag bolt like above. For a wood wall, simple wood screws should work. For smooth tile or glass, consider any epoxy adhesive.
How do you poke a hole in a tennis ball?
With scissors or you could use an electronic drill. Others use a knife. Drills work the best.
