0
At a garden center, hardware store, or feed store.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where is the object twine located in sims 2 castaway?
Twine is not an object or a plant. You find sisal first, then you make twine on a crafting bench.
How do you find twine in Farmville collection?
You collect it from your sheep.
Easy diy twine rug?
Diy twine rugs are easy crafts that you can make out of twine by braiding.
When Jem and Scout find the ball of gray twine in the knothole what does Jem suggest they do?
Jem suggests that they not take the ball of gray twine from the knothole as it may be someone else's hiding spot or treasure. He feels that it is important to respect the mystery surrounding the knothole and leave the twine where they found it.
Where does twine come from?
Twine is made from both plants and synthetic fibers. The two products are mixed to together to make the final twine product.
How do you use twine as a sentence?
I used twine to help my dad.
How do you get twine on FarmVille?
The collectible twine can be found when harvesting sheep on your farm.
Is twine recyclable?
If the twine is made from a natural fiber, like hemp, sisal or even cotton, then it is biodegradable.Some twine is made of plastic. This is not biodegradable.
What can a man do to get twine?
You get some coarse wool, and then you use a spinning wheel in order to make find string. This used to be twine in pagan days. However now twine can be made out of dyed plastic or even dyed cotton. Machines have taken over the spinning wheel, and it is made at professional standard at high rate.
Where can you find hemp twine?
Usually at any garden center, hardware store, or farm/feed store.
What has the author F Twine written?
F. Twine has written: 'Low pay in Scotland'
How do you thread a McCormick IH Forty Six baler?
THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.
