What would you like to do?
The cam position sensor on the 3.5l or the 4.0 v8 engine is on the front of the rear head. TechJK ---------------------------------------------------------- Cam Sensor Behind Starter The camshaft positioning sensor is hidden behind the starter motor on the 3.5 6-cyl. engine. I think it's the same for the 4.0. The starter motor must be removed to replace the sensor.
102 people found this useful
Was this answer useful?
Thanks for the feedback!
Where is the camshaft position sensor located on a 1998 Oldsmobile intrigue and how do you replace it?
Answer For the 3.5 L motor. Looking at the engine from the front of the car, the camshaft position sensor is located on the left side of the re…ar head. If you remove the coolant overflow container, you will be able to find it very easily. You will need a 10mm wrench of socket to remove the set bolt, then with a flat screw driver you can very gently pry it out. Just pop the new one in and tighten the bolt. Be careful when attaching the plug.
Answer The Camshaft Position Sensor is located behind the Power Steering Pump.
Answer Haynes repair manual, Dodge Neon 2000 thru 2003. Book #30036 I think the question was where is it located on the car, not which book do I buy to find the lo…cation. It is located at the end of the cylinder head. Its the black plastic part with an electrical connector on it.
If you are pulling OBD code P1361, or if you are having problems with the car periodically losing power suddenly (revs drop to about 1k, car will not accelerate, check engine …light comes on) there is a good post here: http://www.honda-tech.com/zerothread/556968 If you have the hood up, facing the engine, it is just to the right of the valve cover, underneath (closer to the ground) and behind (inset an inch or so) the timing belt cover. The sensor is oriented so that oval female connector it is facing the driver's side wheel. To locate it without first taking everything off, stand on the driver's side of the engine bay, and look or feel down the gap between the engine and the steel hoses (power steering IIRC) attaching to the quarter panel nearest you. There should be some cables terminating at a round rubber grommet 4-6" from the top of the engine - this is the electrical connection to the CMP. The gray plastic piece the grommet plugs in to is the timing belt cover. To replace it you can do pretty much all the work with a 10mm socket - have some socket extensions of various length, gloves and patience. You'll have to remove the valve and timing belt cover - start to finish, it took me about three hours. I suggest getting a manual for visual and technical reference. I was able to find this part at a local O'Reilly - part number CSS1618. Other stores (including dealers) in my area did not stock them. And, not only did they stock the part, they were the cheapest source - I compared the two parts once I had the original out, and the the new part was identical to the OEM, down to the factory markings. Good luck HTH...
Where are the camshaft position sensor and crankshaft position sensors located in a 1996 olds aurora?
Answer where are the camshaft position
under the power steering pump in the top of the engine.
Where is the camshaft position sensor located on a 2000 Oldsmobile intrique and how do you replace it?
Right next too the coolant resvervior remove it and you will see it. Unplig the pigtail and remove the 10 mm bolt holding it into place.
Where is the camshaft position sensor located on a 95 Oldsmobile aurora v8 4.0 and the crankshaft sensor?
Stop by your local Library and rent a Haynes or Chilton Manual. You can find the location in there. You can also stop by any Auto Zone Store and they can show you on the… computer or on your car. You can log on to autozone.com and the site can sometimes give you a picture or an idea of where the part is located. Free. Just don't buy any electrical parts from Auto Zone. Bad quality. Peace.
On a single cam ford focus 2000-2001 the cam position sensor is below the pcv valve. If looking at the engine it is on the right side, rear, about a 3inches from the top of th…e engine.
I need to locate the IAT sensor on my 2001 Aurora
show location of camshaft position sensor for 2002 Oldsmobile bravada.
It is located beneath the power steering pump in the engine block
Front of the engine, points at the driver side cam sprocket.
In Ford F-150
The camshaft position sensor on a 2001 ford mustang is located on the front of the engine. It is behind the power steering fluid reservoir.
Behind oil filter
See related answers