What would you like to do?
Stop by your local Library and rent a Haynes or Chilton Manual. You can find the location in there. You can also stop by any Auto Zone Store and they can show you on the computer or on your car. You can log on to autozone.com and the site can sometimes give you a picture or an idea of where the part is located. Free. Just don't buy any electrical parts from Auto Zone. Bad quality. Peace.
1 person found this useful
Was this answer useful?
Thanks for the feedback!
The cam position sensor on the 3.5l or the 4.0 v8 engine is on the front of the rear head. TechJK . ----------------------------------------------------------. Cam Sensor …Behind Starter . The camshaft positioning sensor is hidden behind the starter motor on the 3.5 6-cyl. engine. I think it's the same for the 4.0. The starter motor must be removed to replace the sensor.
Answer The Camshaft Position Sensor is located behind the Power Steering Pump.
Answer inside of distributor
Your Aurora has 2 Crankshaft positioning sensors. I just replaced both of the CPS on my 2003 Aurora on 6/2/2012. They are located under the car, near the oil filter. If you …raise the car, laying down looking up at the oil filter- The sensors will be to the left of it. To me, this was not an easy fix. The hardest part was getting the connectors off. I took off the oil pressure sensor, to allow more space to work. The sensors are held in by one #10 socket. If those sensor were located right under the hood.. this would be a 5 minute job. Its the location of the sensors that's a pain in the a$$. Good Luck.
Where are the camshaft position sensor and crankshaft position sensors located in a 1996 olds aurora?
Answer where are the camshaft position
It is located on the distributor under the cap and rotor Crank sensor should be on the front bottom of engine by the crank pulley
I have a 2000 and I'm assuming it's the same for 2002. There is 2 on the gm 3.4l engine. One is in the front behind the crankshaft pulley/damper (in front of the right front w…heel, tranverse mount engine), the other is on the firewall side of the engine. Both can and will go out, replace both at the same time. One common problem is the lead wire from the side crank sensor fails due to heat from the exhaust manifold destroys the insulation and the wire grounds out on the body giving an constant or intermittent engine misfire.
If your 3.5 engine is the same as that in a 2001 Olds Aurora, go to www.autorepair.about.com and search on "2001 aurora 3.5 crank sensor". One of the hits will be a diag…ram of where the crank sensor is located (above the starter motor). Note that for this engine, a "relearn" mjust be done after replacing the sensor. There is a link to the procedure for removing/installing the sensor and for doing the "relearn". Hope this helps
Where is the crankshaft position sensor and the camshaft position sensor located on a 1997 Pontiac Grand Am?
It is located on the firewall side of the engine. Towards the passenger side. Just above the oil pan. (The original respondent) just replaced one on a 1991 3.1 liter. I …was lucky that I had access to a lift. It was sort of a pain but I got it replaced in about 45 minutes. The bolt is 8mm. Use a 1/4 drive with a long extension.
Where is the crankshaft position sensor and the camshaft position sensor located on a 1990 Mitsubishi Eclipse?
Found it at front bottom of engine
I'm not a mechanic / technician but from what I have read : The camshaft position sensor on top of the camshaft position synchronizer on the Ford 4.0 lit…er EFI , V6 engine , is on top of the engine , near the center line , at the back of the engine near the firewall * apparently you can't see it until the upper intake manifold is removed
ANSWER: CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE REMOVAL The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CK…P Sensor Location/Removal/Installation - 4.7L V - 8 Engine It is positioned and bolted into a machined hole in the engine block Disconnect CKP electrical connector at sensor. Remove CKP mounting bolt CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers. Remove sensor from vehicle. Check condition of sensor o-ring. INSTALLATION Clean out machined hole in engine block. Apply a small amount of engine oil to sensor o-ring. Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result. Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque. Connect electrical connector to sensor.
opel omega crankshaft sensor is located next tp the oil filter atached with a star shaped screw, to remove it you have to remove the oil filter first. or the muffler.
The 1995 Oldsmobile Aurora 4.0 liter engine crank sensor is located on the back of the crank. You will need to remove the rear engine cover in order to view the crank sens…or.
In Toyota Camry
Where are the crankshaft position sensor and the camshaft position sensor located on a 4cyl 95 Toyota Camry?
The crankshaft position sensor must be behind the timing belt cover next to the crankshaft and behind the crankshaft pulley. The camshaft position sensor is again under the ti…ming belt cover next to the camshaft and behind and the camshaft pulley. Is it the same place in 2000 Camry 4Cyl? Do you have pictures of the location? Hard or easy to replace, and what tools do I need? Thanks alot
From the front of the vehicle the sensor is left of the harmonic balancer and above it.