0
Which terminal represents the control input of a bipolar transistor?
Wiki User
∙ 10y ago
base
Umm....
Device current results from forward biasing of the emitter-base junction.
Thus you can:
1. hold the emitter constant and apply control to the base (most common), or
2. hold the base constant and apply control to the emitter (common/grounded base circuit, mostly used at high/very high frequencies).
Wiki User
∙ 10y ago
Aya
The gate or the base or the collector or the emitter
Add your answer:
Earn +20 pts
What are the characteristics of bipolar junction transistor?
A Bipolar Junction Transistor(a.k.a. a BJT or BipolarTransistor) is an activesemiconductor deviceformed by twoP-N junctionswhose function is amplification of an electriccurrent.
What is the difference between a transistor and scr?
SCR or Silicon Controlled Rectifiers are Bipolar junctions Transistor ( Thyristor Family), SCRs are made of two transistors thats why they PNPN or NPNP devices. The three important parts of transistor are - Emitter, Collector & Base. & the Three Important parts of SCR are - Anode, Cathode & Gate. Use of SCRs- rectification of high power AC & power control applications, such as lamp dimming, regulators and motor control. Use of Transistors - switch, audio, high voltage, amplifiers, switcher
Is BJT is a current control device or voltage control device?
transistor is a current controlled device. as the current flows through the base of the transistor , it works like a close switch.
What are the two main uses of a transistor?
a) to act as a switching device; a change in the bias voltage at the base- emitter junction can cause an increase in signal flowing through the transistor through the collector terminal and this cause the output voltage at the collector terminal to change; eg to drop to a low voltage level, this is seen as the transistor device switching on to maximum conduction rate and a low level output at the collector. b) to act an amplifer . whether the input signal is an ac type signal in which case its a signal power amplifer function; eg sound amplifer control circuits , or whether a dc input signal, in which case the input dc signal is amplfied to be reproduced as a bigger signal at the output collector terminal
Zener Regulation with a varying load?
Zener diodes attempt to keep terminal voltage constant. If the load is fairly small, a single zener diode can be used for this purpose. If the load is large enough that the zener cannot hold the voltage within desired margins, I suggest using the zener to control the base of a power transistor; the emitter or collector (depending on transistor type) will be used as the output to the load.
What is FET?
FET is abbreviation of Field Effect Transistor. This is a transistor in which current is controlled by voltage only and no current is drawn. It is a high input impedence device and is used in computers, telecommunication and control circuits. This transistor is better in certain parameters as compared to BJT, that is Bipolar Junction Transistor.
How does a transistor electronically switch the output on?
A transistor can electronically switch the output by controlling the flow of current between its two terminals, called the collector and emitter. It has a third terminal, called the base, which acts as a control input. When a small current is applied to the base terminal, it influences the flow of current between the collector and emitter terminals, effectively turning the transistor "on" or "off" and allowing it to change the output state.
Why is a fet so called?
FET stands for Filed Effect Transistor. Bipolar transistors have junctions to control current but a FET does it by controlling the conductivity of a single channel by altering the electric Field of that channel.
Why is fet so called?
FET stands for Filed Effect Transistor. Bipolar transistors have junctions to control current but a FET does it by controlling the conductivity of a single channel by altering the electric Field of that channel.
What is the definition of a transistor?
A transistor is a three-terminal electronic component composed of semiconducting material such as silicon or germanium. the purpose of a transistor is to use a small signal to vary the conductivity of a piece of semiconductor. The tiny signal can switch a large current on and off. Or, the signal can be used to control a larger signal, so the transistor becomes an amplifier. In Bipolar Junction transistors the large current must pass across an extremely thin insulating layer, and the width of this insulating layer controls the current.In Field Effect Transistors the large current must pass through a narrow conductive channel with insulating layers on either side. The width of this conductive channel controls the current.See also:How_does_a_transistor_work
What are the characteristics of bipolar junction transistor?
A Bipolar Junction Transistor(a.k.a. a BJT or BipolarTransistor) is an activesemiconductor deviceformed by twoP-N junctionswhose function is amplification of an electriccurrent.
What is the difference between a transistor and scr?
SCR or Silicon Controlled Rectifiers are Bipolar junctions Transistor ( Thyristor Family), SCRs are made of two transistors thats why they PNPN or NPNP devices. The three important parts of transistor are - Emitter, Collector & Base. & the Three Important parts of SCR are - Anode, Cathode & Gate. Use of SCRs- rectification of high power AC & power control applications, such as lamp dimming, regulators and motor control. Use of Transistors - switch, audio, high voltage, amplifiers, switcher
Does birth control affect bipolar disorder?
No
What is a resistor and a transistor?
there is 2 types of componant 1-passive compnant:who provide a fixed voltage to active componant we can not use them in rectification or amplification,registor,capacitor,inductor 2-active componant:we can use its as a amplifier r rectifier,diode,transistor,scr,etc (we can use registor for voltage drop,so it is passive componant)
How do you use the Transistor output terminals of an electronic counter in a Electrical control circuit?
They use transistor as the purpose to transfer the voltage
What is a power transistor on a Hyundai scoupe?
its the ignition control module
Is BJT is a current control device or voltage control device?
transistor is a current controlled device. as the current flows through the base of the transistor , it works like a close switch.
