0
The basic assumption I am making is that your oven is on its own breaker with nothing else on the circuit. If oven is sharing circuit, unplug other devices.
The problem is either with your breaker, the oven itself or the wire. If you have a good clamp-on ampmeter and know how to use it you can measure the current and see how it compares to the breaker rating. Provided the breaker doesn't trip instantaneously.
To isolate the problem to the oven, make sure all stove top elements are off. Start with oven temp on lowest setting. If this trips breaker immediately there is a problem with your oven heating element or elements. There may be more than one. Somehow the resistance in the element has decreased or shorted and too much current is flowing. If the breaker doesn't blow immediately, there may still be a problem with element, but as you turn up the heat more voltage is applied to the element causing more current to flow. This would rule out a dead short, but not a bad element.
If a new element doesn't fix the problem it may be a faulty breaker. You could test this by swapping the breaker with a know working breaker of the same ratings from your electric panel. You should only do this if you know what you are doing, because electrocution is possible.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why is the breaker tripping when you turn on the oven?
An electrical short in the wiring, or a defect in the oven itself. Have it checked out by a qualified technician.
If a 100a breaker keeps tripping?
If a 100 amp breaker keeps tripping there is an overload on the system.
Which wire is used to install a double oven and a stove?
Normally older ovens required a AWG #8 wire on a 40 amp breaker. On a modern double oven I would recommend you install AWG #6 on a 50 amp breaker. That way you are safe and will not have to worry about the breaker tripping. It will cost a little more but is worth it in the long run.
How does a circuit breaker use an electromagnet?
The electromagnet in the circuit breaker is used for instantaneous tripping if short-circuit condition arises. At defined current level the electromagnet develops the force high enough to cause the tripping of the mechanism.
Does a hot day trip a circuit breaker?
The ambient temperature does have an effect on the tripping point of a breaker. If a breaker is operating at near capacity the additional ambient temperature will lower the breaker trip set point.
Why is the breaker tripping when you turn on the oven?
An electrical short in the wiring, or a defect in the oven itself. Have it checked out by a qualified technician.
If a 100a breaker keeps tripping?
If a 100 amp breaker keeps tripping there is an overload on the system.
Which wire is used to install a double oven and a stove?
Normally older ovens required a AWG #8 wire on a 40 amp breaker. On a modern double oven I would recommend you install AWG #6 on a 50 amp breaker. That way you are safe and will not have to worry about the breaker tripping. It will cost a little more but is worth it in the long run.
SMy Breaker box is tripping one of my 20A's How many times can I just reset it before I have to shut it down?
If you have contineous tripping on a breaker then there is a fault on the load of that breaker. Don't reset it any more. What is the breaker connected to?
Shop vac trips house breaker?
If the Shop Vac is tripping the breaker to a house turn other electronics off while it is in use. The power in the house should be checked out by a electrician.
What is the metal piece on the circuit breaker preventing it from tripping?
A circuit breaker is designed so that it will trip when the electric current is too high. That is the purpose of a circuit breaker. If there is a metal piece on the circuit breaker that prevents it from tripping, it is useless. Perhaps someone has altered it.
Why does your main circuit breaker trip when your dryer runs 15 minutes Is it because your vent needs to be cleaned?
Could be but you could also have a weak breaker that will no longer hold the load of your dryer. That is if your talking about your dryer breaker tripping. If your "main breaker" is tripping you have a different problem. Call an electrician in that case. A plugged up dryer shouldn't be tripping your main
What does tripping off means?
In an electrical context, 'tripping off' means the circuit breaker breaking the circuit because of a fault.
How does a circuit breaker use an electromagnet?
The electromagnet in the circuit breaker is used for instantaneous tripping if short-circuit condition arises. At defined current level the electromagnet develops the force high enough to cause the tripping of the mechanism.
Does a hot day trip a circuit breaker?
The ambient temperature does have an effect on the tripping point of a breaker. If a breaker is operating at near capacity the additional ambient temperature will lower the breaker trip set point.
What would cause a breaker to trip?
A breaker will keep tripping until the fault that caused it to trip is corrected. That's what it is designed to do. There's either a circuit overload or a short circuit. How fast the breaker trips can indicate how overloaded it is. If you are very close to the rating of the breaker you can actually trip it over time. If you are definitely over the breaker will usually trip instantly. If there is a short circuit you can usually tell that by how violently the breaker trips. If you have conduit you can hear the wires banging around in the pipe. A frequently tripping breaker may also be faulty and need to be replaced - breakers are designed to fail by tripping prematurely rather than by not tripping at all, as this is much safer. This is very often the case for breakers that trip at seemingly random intervals, often when very little load is being drawn.
What can cause a circuit breaker to suddenly start tripping?
If the breaker trips when nothing is turned on it could be a mouse problem. If it only trips when certain lights or appliances are turned on one of them is probably the reason.If it trips when nothing is being turned on or off something is getting hot. You should then have qualified electrician look at it. Hope this is usefull.
