0
Why would cold water pressure fade in and out throughout a house?
Wiki User
∙ 17y ago
poor water pressure from your city. Or if you are on a well, the pump might be going bad.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
What would cause no water flow at all throughout the house and could it be the pressure tank?
== == Two possible problems............... The main shut off valve in the house is closed from the in-coming city water supply line, or the city supply line is shut off at the street .
What would make the water pressure in a house go above 80 psi?
Area water authority could have increased water main pressure, no or defective expansion tank in house main water line if house has a backflow preventer installed, or defective /not properly set pressure reducing valve.
What causes high water pressure in the first faucet on the water line from where it enters the house. The cold water is under high pressure but other faucets in house are fine.?
Possibly a pressure reducing valve installed after piping for first faucet, which would cause situation describing.
What would cause tank to have good pressure but not allow water to flow through the house?
If it's a bladder tank, it should always have "Air" pressure but if the pump isn't working, you still wouldn't have water in the house.
If you run water in your house and it has good pressure for a few seconds then pressure goes away what would be the cause?
Ferrous metal piping
Can you have too much water pressure in a residential house requiring a pressure release valve?
The water pressure in my house is about 140PSI. Which is definitely dangerous. It happens more often than you would think. What happens is a city will use water supply lines which are too small for the water requirements. Therefore, they have to increase the pressure. You wouldn't want a pressure relief valve, because then if the pressure was too high, it would just spray water everywhere to release the pressure. You would want a pressure regulator installed, which is what I am working on for my house right now. Just to let you know though, you may have to get a thermal expansion tank for your water heater if you don't have one. See, the new pressure regulators have a check valve in them, which prevents water from traveling back into the city pipes once it has gotten into your house. When your water heater heats the water, the air bubbles in it expand, which increases the water pressure, and will probably cause your pressure relief valve on your water heater to blow. You can get a cheap water pressure meter at any improvement store to check it out. 50-60 PSI is ok. I would say you could take it up to 70 or 80 PSI safely.
Would you ever want higher than 80 psi water pressure in a house?
For normal usage, no, not necessary. Higher pressure puts added strain on fixture water piping.
What are the Requirements of piping for flush valve alignment having good pressure of water throughout?
Tieger plumbingThe alignment would depend on the roughing measurements for the fixture being serviced and the water pressure has to do with the incoming pressure available and the size of the supply for the volume required.
What causes sudden pressure surges in your faucets and refrigerator door water dispenser?
I would purchase a Watt water pressure guage from your local home improvement or hardware store and check your water pressure at your faucet. If water pressure is greater than 40-45psi your regulator needs to be turned down where the water comes into the house.
How do you correct low water pressure?
If it's the whole house, turn the screw clockwise at the PRV to increase the pressure. If it is something else, you would have to explain it more.
What is the optimum water pressure for home use?
The optimum water pressure for most homes is typically in the range of 40-60 pounds per square inch (psi). This range provides enough pressure for efficient water flow throughout the house without causing damage to pipes, fixtures, or appliances. It's important to note that local building codes and regulations may specify a specific range, so it's recommended to consult with a professional plumber or check with your local water department for the recommended water pressure in your area.
Would adjusting your pressure reducer help with low water pressure in the house?
yes. loosen the locking nut, adjust the screw / bolt down to increase psi, out to decrease psi.
