IEEE 802.11n-2009: Information from Answers.com

IEEE 802.11n-2009 is an amendment to the IEEE 802.11-2007 wireless networking standard to improve network throughput over previous standards, such as 802.11b and 802.11g, with a significant increase in the maximum raw OSI physical layer (PHY) data rate from 54 Mbit/s to a maximum of 600 Mbit/s with the use of four spatial streams at a channel width of 40 MHz.^[1]^[2]

Since 2007, the Wi-Fi Alliance has been certifying interoperability of "draft-N" products based on what was draft 2.0 of IEEE 802.11n specification.^[3] The Alliance has upgraded its suite of compatibility tests for some enhancements finalized after Draft 2.0. Furthermore, its has affirmed that all draft-n certified products remain compatible with the products conforming to the final standards.^[4]

1 Description
2 Deployment strategies
- 2.1 40MHz in 2.4GHz
3 Wi-Fi Alliance
4 Timeline
5 CSIRO patent issues
6 Comparison
7 See also
8 Standard
9 References

Description

IEEE 802.11n builds on previous 802.11 standards by adding multiple-input multiple-output (MIMO) and 40 MHz channels to the physical (PHY) layer, and frame aggregation to the MAC layer. MIMO is a technology which uses multiple antennas to coherently resolve more information than possible using a single antenna. Two important benefits it provides to 802.11n are antenna diversity and spatial multiplexing.

Another ability MIMO technology provides is Spatial Division Multiplexing (SDM). SDM spatially multiplexes multiple independent data streams, transferred simultaneously within one spectral channel of bandwidth. MIMO SDM can significantly increase data throughput as the number of resolved spatial data streams is increased. Each spatial stream requires a discrete antenna at both the transmitter and the receiver. In addition, MIMO technology requires a separate radio frequency chain and analog-to-digital converter for each MIMO antenna which translates to higher implementation costs compared to non-MIMO systems.

40 MHz channels is another feature incorporated into 802.11n which doubles the channel width from 20 MHz in previous 802.11 PHYs to transmit data. This allows for a doubling of the PHY data rate over a single 20 MHz channel. It can be enabled in the 5 GHz mode, or within the 2.4 GHz if there is knowledge that it will not interfere with any other 802.11 or non-802.11 (such as Bluetooth) system using those same frequencies.^[5]

Coupling MIMO architecture with wider bandwidth channels offers increased physical transfer rate over 802.11a (5 GHz) and 802.11g (2.4 GHz).^[6]

Data encoding

The transmitter and receiver use precoding and postcoding techniques, respectively, to achieve the capacity of a MIMO link. Precoding includes spatial beamforming and spatial coding, where spatial beamforming improves the received signal quality at the decoding stage. Spatial coding can increase data throughput via spatial multiplexing and increase range by exploiting the spatial diversity, through techniques such as Alamouti coding.

Number of antennas

The number of simultaneous data streams is limited by the minimum number of antennas in use on both sides of the link. However, the individual radios often further limit the number of spatial streams that may carry unique data. The $a \times b \colon c$ notation helps identify what a given radio is capable of. The first number ( $a$ ) is the maximum number of transmit antennas or RF chains that can be used by the radio. The second number ( $b$ ) is the maximum number of receive antennas or RF chains that can be used by the radio. The third number ( $c$ ) is the maximum number of data spatial streams the radio can use. For example, a radio that can transmit on two antennas and receive on three, but can only send or receive two data streams would be $2 \times 3 \colon 2$ .

The 802.11n draft allows up to $4 \times 4 \colon 4$ . Common configurations of 11n devices are $2 \times 2 \colon 2$ , $2 \times 3 \colon 2$ , and $3 \times 3 \colon 2$ . All three configurations have the same maximum throughputs and features, and differ only in the amount of diversity the antenna systems provide. In addition, a fourth configuration, $3 \times 3 \colon 3$ is becoming common, which has a higher throughput, due to the additional data stream^[7].

Data rates

Data rates up to 600 Mbit/s are achieved only with the maximum of four spatial streams using a 40 MHz-wide channel. Various modulation schemes and coding rates are defined by the standard and are represented by an MCS index value. The table below shows the relationships between the variables that allow for the maximum data rate.^[8]

MCS Index	Spatial Streams	Modulation Type	Coding Rate	Data Rate Mb/s
				20 MHz channel		40 MHz channel
				800ns GI	400ns GI	800ns GI	400ns GI
0	1	BPSK	1/2	6.50	7.20	13.50	15.00
1	1	QPSK	1/2	13.00	14.40	27.00	30.00
2	1	QPSK	3/4	19.50	21.70	40.50	45.00
3	1	16-QAM	1/2	26.00	28.90	54.00	60.00
4	1	16-QAM	3/4	39.00	43.30	81.00	90.00
5	1	64-QAM	2/3	52.00	57.80	108.00	120.00
6	1	64-QAM	3/4	58.50	65.00	121.50	135.00
7	1	64-QAM	5/6	65.00	72.20	135.00	150.00
8	2	BPSK	1/2	13.00	14.40	27.00	30.00
9	2	QPSK	1/2	26.00	28.90	54.00	60.00
10	2	QPSK	3/4	39.00	43.30	81.00	90.00
11	2	16-QAM	1/2	52.00	57.80	108.00	120.00
12	2	16-QAM	3/4	78.00	86.70	162.00	180.00
13	2	64-QAM	2/3	104.00	115.60	216.00	240.00
14	2	64-QAM	3/4	117.00	130.00	243.00	270.00
15	2	64-QAM	5/6	130.00	144.40	270.00	300.00
...	...	...	...	...	...	...	...
31	4	64-QAM	5/6	260.00	288.90	540.00	600.00

Frame aggregation

PHY level data rate improvements do not increase user level throughput beyond a point because of 802.11 protocol overheads, like the contention process, interframe spacing, PHY level headers (Preamble + PLCP) and acknowledgment frames. The main medium access control (MAC) feature that provides a performance improvement is aggregation. Two types of aggregation are defined:

Aggregation of MAC Service Data Units (MSDUs) at the top of the MAC (referred to as MSDU aggregation or A-MSDU)
Aggregation of MAC Protocol Data Units (MPDUs) at the bottom of the MAC (referred to as MPDU aggregation or A-MPDU)

Aggregation is a process of packing multiple MSDUs or MPDUs together to reduce the overheads and average them over multiple frames, thus increasing the user level data rate. A-MPDU aggregation requires the use of Block Acknowledgement or BlockAck, which was introduced in 802.11e and has been optimized in 802.11n.

Backward compatibility

When 802.11g was released to share the band with existing 802.11b devices, it provided ways of ensuring coexistence between the legacy and the new devices. 802.11n extends the coexistence management to protect its transmissions from legacy devices, which include 802.11g, 802.11b and 802.11a. There are MAC and PHY level protection mechanisms as listed below:

PHY level protection: Mixed Mode Format protection (also known as L-SIG TXOP Protection): In mixed mode, each 802.11n transmission is always embedded in a 802.11a or 802.11g transmission. For 20 MHz transmissions, this embedding takes care of the protection with 802.11a and 802.11g. However, 802.11b devices still need CTS protection.
PHY level protection: Transmissions using a 40 MHz channel in the presence of 802.11a or 802.11g clients require using CTS protection on both 20 MHz halves of the 40 MHz channel, to prevent interference with legacy devices.
PHY level protection: An RTS/CTS frame exchange or CTS frame transmission at legacy rates can be used to protect subsequent 11n transmission.

Even with protection, large discrepancies can exist between the throughput an 802.11n device can achieve in a greenfield network, compared to a mixed-mode network, when legacy devices are present. This is an extension of the 802.11b/802.11g coexistence problem.

Deployment strategies

To achieve maximum throughput a pure 802.11n 5 GHz network is recommended. The 5 GHz band has substantial capacity due to many non-overlapping radio channels and less radio interference as compared to the 2.4 GHz band.^[9] An 802.11n-only network may be impractical for many users because the existing computer stock is predominantly 802.11b/g only. Replacement of incompatible WiFi cards or of entire laptop stock is necessary for older computers to operate on the network. Consequently, it may be more practical in the short term to operate a mixed 802.11b/g/n network until 802.11n hardware becomes more prevalent. In a mixed-mode system, it is generally best to use a dual-radio access point and place the 802.11b/g traffic on the 2.4 GHz radio and the 802.11n traffic on the 5 GHz radio.^[10]

40MHz in 2.4GHz

The 2.4GHz ISM band is fairly congested. With 802.11n, there is the option to double the bandwidth per channel to 40 MHz which results in slightly more than doubles the data rate. However, when in 2.4 GHz enabling this option takes up to 82%^[11] of the unlicensed band, which in many areas may prove to be infeasible.

The specification calls for requiring one main 20 Mhz channel as well as an adjacent channel spaced ±20 MHz away. The main channel is used for communications with clients incapable of 40 MHz mode. When in 40 MHz mode the center frequency is actually the mean of the main and auxiliary channels.

Main Channel	20 MHz	40 MHz Upper			40 MHz Lower
Main Channel	blocks	Aux.	center	blocks	Aux.	center	blocks
1	1-3	5	3	1-7	Not Available
2	1-4	6	4	1-8	Not Available
3	1-5	7	5	1-9	Not Available
4	2-6	8	6	2-10	Not Available
5	3-7	9	7	3-11	1	3	1-7
6	4-8	10	8	4-12	2	4	1-8
7	5-9	11	9	5-13	3	5	1-9
8	6-10	12^†	10^†	6-13	4	6	2-10
9	7-11	13^†	11^†	7-13	5	7	3-11
10	8-12	Not Available			6	8	4-12
11	9-13	Not Available			7	9	5-13
12^†	10-13	Not Available			8^†	10^†	6-13
13^†	11-13	Not Available			9^†	11^†	7-13

^† = Setting not available in North America.

Wi-Fi Alliance

As of mid-2007, the Wi-Fi Alliance has started certifying products based on IEEE 802.11n Draft 2.0.^[12] This certification program established a set of features and a level of interoperability across vendors supporting those features, thus providing one definition of 'draft n'. The Baseline certification covers both 20 MHz and 40 MHz wide channels, and up to two spatial streams, for maximum throughputs of 144.4 Mbit/s for 20 MHz and 300 Mbit/s for 40 MHz (with Short Guard interval). A number of vendors in both the consumer and enterprise spaces have built products that have achieved this certification.^[13] The Wi-Fi Alliance certification program subsumed the previous industry consortium efforts to define 802.11n, such as the now dormant Enhanced Wireless Consortium (EWC). The Wi-Fi Alliance is investigating further work on certification of additional features of 802.11n not covered by the Baseline certification, including higher numbers of spatial streams (3 or 4), Greenfield Format, PSMP, Implicit & Explicit Beamforming and Space-Time Block Coding.

Timeline

The following are milestones in the development of 802.11n:^[14]

September 11, 2002: The first meeting of the High-Throughput Study Group (HTSG) was held. Earlier in the year, in the Wireless Next Generation standing committee (WNG SC), presentations were heard on why they need change and what the target throughput would be required to justify the amendments. Compromise was reached in May 2002 to delay the start of the Study Group until September to allow 11g to complete major work during the July 2002 session.

September 11, 2003: The IEEE-SA New Standards Committee (NesCom) approves the Project Authorization Request (PAR) for the purpose of amending the 802.11-2007 standard. The new 802.11 Task Group (TGn) is to develop a new amendment. The TGn amendment is based on IEEE Std 802.11-2007, as amended by IEEE Std 802.11k-2008, IEEE Std 802.11r-2008, IEEE Std 802.11y-2008 and IEEE P802.11w. TGn will be the 5th amendment to the 802.11-2007 standard. The scope of this project is to define an amendment that shall define standardized modifications to both the 802.11 physical layers (PHY) and the 802.11 Medium Access Control Layer (MAC) so that modes of operation can be enabled that are capable of much higher throughputs, with a maximum throughput of at least 100Mbps, as measured at the MAC data service access point (SAP).

September 15, 2003: The first meeting of the new 802.11 Task Group (TGn).

May 17, 2004: Call for Proposals is issued.

September 13, 2004: 32 first round of proposals are heard.

March 2005: Proposals are downselected to a single proposal, but there is not a 75% consensus on the one proposal. Further efforts are expended over the next 3 sessions without being able to agree on one proposal.

July 2005: Previous competitors TGn Sync, WWiSE, and a third group, MITMOT, said that they would merge their respective proposals as a draft. The standardization process is expected to be completed by the second quarter of 2009.

January 19, 2006: The IEEE 802.11n Task Group approved the Joint Proposal's specification, enhanced by EWC's draft specification.

March 2006: IEEE 802.11 Working Group sent the 802.11n Draft to its first letter ballot, allowing the 500+ 802.11 voters to review the document and suggest bug fixes, changes, and improvements.

May 2, 2006: The IEEE 802.11 Working Group voted not to forward Draft 1.0 of the proposed 802.11n standard. Only 46.6% voted to approve the ballot. To proceed to the next step in the IEEE standards process, a majority vote of 75% is required. This letter ballot also generated approximately 12,000 comments—many more than anticipated.

November 2006: TGn voted to accept draft version 1.06, incorporating all accepted technical and editorial comment resolutions prior to this meeting. An additional 800 comment resolutions were approved during the November session which will be incorporated into the next revision of the draft. As of this meeting, three of the 18 comment topic ad hoc groups chartered in May had completed their work, and 88% of the technical comments had been resolved, with approximately 370 remaining.

January 19, 2007: The IEEE 802.11 Working Group unanimously (100 yes, 0 no, 5 abstaining) approved a request by the 802.11n Task Group to issue a new Draft 2.0 of the proposed standard. Draft 2.0 was based on the Task Group's working draft version 1.10. Draft 2.0 was at this point in time the cumulative result of thousands of changes to the 11n document as based on all previous comments.

February 7, 2007: The results of Letter Ballot 95, a 15-day Procedural vote, passed with 97.99% approval and 2.01% disapproval. On the same day, 802.11 Working Group announced the opening of Letter Ballot 97. It invited detailed technical comments to closed on 9 March 2007.

March 9, 2007: Letter Ballot 97, the 30-day Technical vote to approve Draft 2.0, closed. They were announced by IEEE 802 leadership during the Orlando Plenary on 12 March 2007. The ballot passed with an 83.4% approval, above the 75% minimum approval threshold. There were still approximately 3,076 unique comments, which will be individually examined for incorporation into the next revision of Draft 2.

June 25, 2007: The Wi-Fi Alliance announces its official certification program for devices based on Draft 2.0.

September 7, 2007: Task Group agrees on all outstanding issues for Draft 2.07. Draft 3.0 is authorized, which possibly may go to a sponsor ballot in November 2007.

November 2007: Draft 3.0 approved (240 voted affirmative, 43 negative, and 27 abstained). The editor was authorized to produce draft 3.01.

January 2008: Draft 3.02 approved. This version incorporates previously approved technical and editorial comments. There remain 127 unresolved technical comments. It is expected that all remaining comments will be resolved and that TGn and WG11 will subsequently release Draft 4.0 for working group recirculation ballot following the March meeting.

May 2008: Draft 4.0 approved.

July 2008: Draft 5.0 approved and anticipated publication timeline modified.

September 2008: Draft 6.0 approved.

November 2008: Draft 7.0 approved.

January 2009: Draft 7.0 forwarded to sponsor ballot; the sponsor ballot was approved (158 for, 45 against, 21 abstaining); 241 comments were received.

March 2009: Draft 8.0 proceeded to sponsor ballot recirculation; the ballot passed by a 80.1% majority (75% required) (228 votes received, 169 approve, 42 not approve); 277 members are in the sponsor ballot pool; The comment resolution committee resolved the 77 comments received, and authorized the editor to create a Draft 9.0 for further balloting.

April 4, 2009: Draft 9.0 passed sponsor ballot recirculation; the ballot passed by a 80.7% majority (75% required) (233 votes received, 171 approve, 41 not approve); 277 members are in the sponsor ballot pool; The comment resolution committee is resolving the 23 new comments received, and will authorize the editor to create a new draft for further balloting.

May 15, 2009: Draft 10.0 passed sponsor ballot recirculation

June 23, 2009: Draft 11.0 passed sponsor ballot recirculation

July 17, 2009: Final WG Approval passed with 53 approve, 1 against, 6 abstain.^[15] Unanimous approval to send Final WG Draft 11.0 to RevCom.^[16]

September 11, 2009: RevCom/Standards Board approval.^[17]

October 29, 2009: Published.^[2]

CSIRO patent issues

The Australian Commonwealth Scientific and Industrial Research Organisation (CSIRO) holds the patent to a component of the 802.11n standard. This component is also part of 802.11a and 802.11g. The IEEE requested from the CSIRO a Letter of Assurance (LoA) that no lawsuits would be filed for anyone implementing the standard. In September 2007, CSIRO responded that it would not be able to comply with this request since litigation was involved.^[18]

In April 2009, it was revealed that CSIRO reached a settlement with 14 companies —Hewlett-Packard, Asus, Intel, Dell, Toshiba, Netgear, D-Link, Belkin, SMC, Accton, 3Com, Buffalo Technology, Microsoft, and Nintendo— on the condition that CSIRO did not broadcast the resolution.^[19]^[20]^[21]

Comparison

802.11 network standards v • d • e
802.11 Protocol	Release^[22]	Freq. (GHz)	Bandwidth (MHz)	Data rate per stream (Mbit/s)^[23]	Typ throughput (Mbit/s) ^{[citation needed]}	Allowable MIMO streams	Modulation	Approximate indoor range^{[citation needed]} (m)	Approximate Outdoor range^{[citation needed]} (m)
–	Jun 1997	2.4	20	1, 2	0.9	1	DSSS	20	100
a	Sep 1999	5 3.7^[y]	20	6, 9, 12, 18, 24, 36, 48, 54	23	1	OFDM	35	120 5000^[y]
b	Sep 1999	2.4	20	1, 2, 5.5, 11	4.3	1	DSSS	38	140
g	Jun 2003	2.4	20	1, 2, 6, 9, 12, 18, 24, 36, 48, 54	19	1	OFDM, DSSS	38	140
n	Oct 2009	2.4/5	20	7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65, 72.2^[z]	30-130^[24]^[25]	4	OFDM	~70	~250^[26]
n	Oct 2009	2.4/5	40	15, 30, 45, 60, 90, 120, 135, 150^[z]	30-130^[24]^[25]	4	OFDM	~70	~250^[26]
^y IEEE 802.11y-2008 extended operation of 802.11a to the licensed 3.7 GHz band. Increased power limits allow for a range up 5000m. As of 2009^[update], it is only being licensed in the United States by the FCC. ^z Assumes Short Guard interval (SGI) enabled, otherwise reduce each data rate by 10%.

Standard

IEEE 802.11n-2009—Amendment 5: Enhancements for Higher Throughput. IEEE-SA. 29 October 2009. doi:10.1109/IEEESTD.2009.5307322.

References

^ Stanford, Michael (September 7, 2007). "How does 802.11n get to 600Mbps?". Wirevolution. http://www.wirevolution.com/2007/09/07/how-does-80211n-get-to-600mbps.
^ ^a ^b IEEE 802.11n-2009—Amendment 5: Enhancements for Higher Throughput. IEEE-SA. 29 October 2009. doi:10.1109/IEEESTD.2009.5307322.
^ Wi-Fi Alliance Reveals New Logo and Announces First Wi-Fi CERTIFIED™ 802.11n Draft 2.0 Products and Test Suite. wi-fi.org. May 16, 2007.
^ Wi-Fi Alliance (September 30, 2009). "Wi-Fi Alliance launches updated Wi-Fi CERTIFIED n program". Press release. http://www.wi-fi.org/news_articles.php?f=media_news&news_id=892.
^ https://mentor.ieee.org/802.11/dcn/09/11-09-0576-03-000n-sp2-40mhz-coexistence-cids-presentation.ppt
^ Wireless Without Compromise: Delivering the promise of IEEE 802.11n
^ Intel Ultimate N Wifi Link 5300 Product Brief (PDF)
^ http://www.airmagnet.com/assets/whitepaper/WP-802.11nPrimer.pdf
^ "How to: Minimize 802.11 Interference Issues". http://www.wireless-nets.com/resources/tutorials/minimize_802.11_interference_issues.html. Retrieved 2008-07-30.
^ "How to: Migrate to 802.11n in the Enterprise". http://www.wireless-nets.com/resources/tutorials/migrate_80211n.html. Retrieved 2008-07-30.
^ Example: Channel 3+7 (also called 3 Upper) reserves the first 9 out of the 11 available in North America.
^ "Wi-Fi Alliance Begins Testing of Next-Generation Wi-Fi Gear". http://www.wi-fi.org/pressroom_overview.php?newsid=574.
^ "WiFi Certified 802.11n draft 2.0 products". http://certifications.wi-fi.org/wbcs_certified_products.php?search=1&advanced=1&lang=en&filter_company_id=&filter_category_id=&filter_subcategory=&filter_cid=&date_from=&date_to=&x=30&y=18&selected_certifications%5B%5D=33. Retrieved 2008-07-18.
^ "IEEE 802.11n Report (Status of Project)". March 16, 2009. http://grouper.ieee.org/groups/802/11/Reports/tgn_update.htm.
^ https://mentor.ieee.org/802.11/dcn/09/11-09-0905-03-0000-july-2009-plenary-presentation-from-wg11-to-802-ec.ppt — Powerpoint Slide 10
^ "July 2009 meeting minutes" (pdf), IEEE 802 LMSC Executive Committee, 17 July 2009, http://www.ieee802.org/minutes/2009-July/20090717-closing-minutes-v0.pdf, retrieved 10 August 2009
^ http://standards.ieee.org/announcements/ieee802.11n_2009amendment_ratified.html
^ "802.11 WG Chairs' received email letter response from CSIRO regarding LoA requests for IEEE P802.11n". 2007-09-27. https://mentor.ieee.org/802.11/public-file/07/11-07-2619-00-0000-802-11-wg-chairs-received-email-letter-response-from-csiro-regarding-loa-requests.doc.
^ Hutcheon, Stephen. Bonanza for CSIRO after landmark patent win, The Sydney Morning Herald, April 23, 2009. Accessed September 1, 2009.
^ Edwards, Kathryn. CSIRO settles wireless battle, Computerworld, April 22, 2009. Accessed September 1, 2009.
^ MacBean, Nic. Patent proceeds to fund new CSIRO research, ABC News, April 22, 2009. Accessed September 1, 2009.
^ "Official IEEE 802.11 working group project timelines". Sept. 19, 2009. http://grouper.ieee.org/groups/802/11/Reports/802.11_Timelines.htm. Retrieved 2009-10-09.
^ "Wi-Fi CERTIFIED n: Longer-Range, Faster-Throughput, Multimedia-Grade Wi-Fi® Networks" (registration required). Wi-Fi Alliance. September 2009. http://www.wi-fi.org/register.php?file=wp_Wi-Fi_CERTIFIED_n_Industry.pdf.
^ "Trendnet 300Mbps Dual Band Wireless N USB Adapter Review". overclockershq.com. 2009-03-27. http://overclockershq.com/index.php?option=com_content&view=article&id=315%3Atrendnet-300mbps-dual-band-wireless-n-usb-adapter-review&catid=34%3Ahardware-reviews&Itemid=56&limitstart=2.
^ "802.11n Client Throughput Performance - Aruba Networks". 2009-11-18. http://www.arubanetworks.com/pdf/technology/TB_11NPERF.pdf.
^ "802.11n Delivers Better Range". Wi-Fi Planet. 2007-05-31. http://www.wi-fiplanet.com/tutorials/article.php/3680781.

v • d • e IEEE Standards

488 · 754 (1985,revs) · 829 · 1003 · 1014-1987 · 1076 · 1149.1 · 1164 · 1219 · 12207 · 1275 · 1284 · 1394 · 1451 · 1471 · 1516 · 1541-2002 · 1547 · 1584 · 1603 · 1613 · 1667 · 1675-2008 · 1900.4 · 854-1987 · SCC41 · 11073

802 series	802 · 802.1 · 802.2 · 802.3 · 802.4 · 802.5 · 802.6 · 802.7 · 802.8 · 802.9 · 802.10 · 802.11 (a b d e g h i j k n p r y) · 802.12 · 802.15 · 802.15.4-2006 · 802.15.4a · 802.16 · 802.21 · 802.22

P series	P1363 · P1619 · P1801 · P1900 · P1901 · P2030

See also: IEEE Standards Association · Category:IEEE standards

This entry is from Wikipedia, the leading user-contributed encyclopedia. It may not have been reviewed by professional editors (see full disclaimer)

Donate to Wikimedia

	What is IEEE 1284? Read answer...
	What is IEEE 802.6? Read answer...
	What are the IEEE sublayers? Read answer...

	What does IEEE 892.1x do?
	How it is work ieee?
	What is the difference between IEEE 1284 a-b and IEEE 1284 a-c?

IEEE 802.11n-2009

Contents