Inductive charging

The neutrality of this article is disputed. Please see the discussion on the talk page. Please do not remove this message until the dispute is resolved. (October 2009)

Magne Charge wall, handheld, and floor mount

Inductive charging uses the electromagnetic field to transfer energy between two objects. A charging station sends energy through inductive coupling to an electrical device, which stores the energy in the batteries. Because there is a small gap between the two coils, inductive charging is one kind of short-distance wireless energy transfer.

The other kind of charging, direct wired contact (also known as conductive charging or direct coupling) requires direct electrical contact between the batteries and the charger. Conductive charging is achieved by connecting a device to a power source with plug-in wires, such as a docking station, or by moving batteries from a device to charger.

Induction chargers typically use an induction coil to create an alternating electromagnetic field from within a charging base station, and a second induction coil in the portable device takes power from the electromagnetic field and converts it back into electrical current to charge the battery. The two induction coils in proximity combine to form an electrical transformer.^[1][2]

Greater distances can be achieved when the inductive charging system uses resonant inductive coupling.

Advantages

Inductive charging carries a far lower risk of electrical shock, when compared with conductive charging, because there are no exposed conductors. The ability to fully enclose the charging connection also makes the approach attractive where water impermeability is required; for instance, inductive charging is used for implanted medical devices that require periodic or even constant external power, and for electric hygiene devices, such as toothbrushes and shavers, that are frequently used near or even in water. Inductive charging makes charging mobile devices more convenient; rather than having to connect a power cable, the device can be placed on a charge plate.^[3]

Disadvantages

One disadvantage of inductive charging is its lower efficiency and increased ohmic (resistive) heating in comparison to direct contact. Implementations using lower frequencies or older drive technologies charge more slowly and generate heat for most portable electronics,^{[citation needed]}; the technology is nonetheless commonly used in some electric toothbrushes and wet/dry electric shavers, partly for the advantage that the battery contacts can be completely sealed to prevent exposure to water. Inductive charging also requires drive electronics and coils that increase manufacturing complexity and cost.^[1][2]

Newer approaches diminish the transfer losses with ultra thin coils, higher frequencies and optimized drive electronics, thus providing chargers and receivers that are compact, efficient^{[citation needed]} and can be integrated into mobile devices or batteries with minimal change.^[4][3] These technologies provide charging time that are the same as wired approaches and are finding their way into mobile devices rapidly. The Magne Charge system used in the GM EV-1, Chevy S-10 EV and Toyota RAV4 EV vehicles employed high-frequency induction to deliver high power at an efficiency of 86% (6.6kW power delivery from a 7.68kW power draw).^[5]

Examples

• Transcutaneous energy transfer (TET) systems in artificial hearts and other surgically implanted devices.

• General Motors' (GM) discontinued EV-1 electric car was charged with an inductive charging paddle, which was inserted into a receptacle on the vehicle. GM and Toyota agreed on a standard inductive charging interface developed by Hughes Electronics for GM called Magne Charge. GM later dropped its support in 2002 when the California Air Resources Board selected the SAE J1772, or "Avcon", conductive charging interface for electric vehicles in California.^[6]

• In 2006, researchers at the Massachusetts Institute of Technology reported that they had discovered an efficient way to transfer power between coils separated by a few meters. The team, led by Marin Soljačić, theorized that they could extend the distance between the coils by adding resonance to the equation. The MIT wireless power project, called WiTricity, uses a curved coil and capacitive plates.^[7][8]

• April 28, 2009: An Energizer inductive charging station for the Wii remote is reported on IGN.^[9]

• At CES in January 2009, Palm, Inc. announced their new Pre smartphone would be available with an inductive charger, though the charger itself will be sold as a separate accessory. The charger is known as the "Touchstone", and a special backplate must be fitted to the Pre in order to be compatible with it.^[10][3]

• In August 2009 A Consortium of interested companies called the Wireless Power Consortium announced they were nearing completion for a new industry standard for low-power Inductive charging^[11]

• In 2009 Dell introduced the Latitude Z600 personal computer with inductive charging feature.^[12]

• In November 2009, Energizer released a Nintendo Wii Remote induction-based charger.

• In 2009 Reference^[13] introduced an Ex approved Torch and Charger aimed at the offshore market. This product was developed by Wireless Power & Communication, a Norwegian based company.

See also

• Charging station
• In-road electric vehicle charger
• Resonant energy transfer
• Environmental technology

References

External links

• How Inductors Work
• How Electric Toothbrushes Recharge Using Inductors
• Inductive Charging
• Wireless Electricity Is Here