tung oil

This article needs additional citations for verification. Please help improve this article by adding reliable references. Unsourced material may be challenged and removed. (January 2009)

Tung oil is used as a wood finishing product. It has two distinct meanings, pure tung oil and tung oil finishes, which are often confused.

Pure tung oil

Showing the golden effect of polymerized tung oil versus bare wood.

Pure Tung oil is made from the pressed seed from the nut of the tung tree. Pure Tung oil is considered a drying oil much as linseed, safflower, poppy and soybean oil. When applied, it provides a tough, highly water-resistant finish which does not darken noticeably with age as does linseed oil. This is not to say that it is a colorless finish; it still has a slight golden tint.

Pure tung oil is also sometimes called “China wood oil”. It has been used for hundreds if not thousands of years in China to seal decorative and marine wood as well as porous masonry.

Polymerized tung oil

Heating or chemical treatment of pure tung oil will substantially increase the viscosity and film-forming quality of the product. The resulting oil will range in consistency from that of maple syrup to that of motor oil. Some brands, such as Lee Valley Tools, include quick evaporating thinners to make it easier to work with and improve wood penetration.

“Tung oil” finishes

“Tung oil finish” refers to a wetted wood look that a succession of penetrating tung oil applications gives. However, it is also a generic term and has been liberally borrowed by paint-and-varnish makers to describe the expected result of using their preparations—which may or may not actually contain any tung oil at all.

Application

The traditional technique for applying pure tung oil is to dilute the oil 1:1 with solvent, then apply a succession of very thin films with soft a non-fuzzy cloth like tee-shirt cotton. Dilutants range from traditional spirits of turpentine to any of the new citrus thinners to VM&P naphtha. The choice of thinner should be guided by how fast the coating needs to set. Naphtha is often too fast, but works well in spray-on applications in well ventilated studios. Primary coats may be laid down at a 1:1 oil-to-thinner ratio, and successive layers, if not absorbed into the wood, at higher solvent to oil concentrations. This technique brings out the deepest color of the wood while maintaining a matte finish.

Tung oil finishes that start with polymerized oils or "tung oil preparations" are best applied in the fat over lean principle: thinned pure oil is applied to deeply penetrate the surface, to fill pores. Straight oil is then applied moderately to adhere to the surface and provide a good base for the thick gloss layers. The polymerized oil is then applied thickly as a single layer, allowed to fully dry, is buffed smooth with very fine sandpaper, then 00 steel wool. The surface is wiped clean with a moistened rag, then allowed to dry. A final coat is again applied fairly thickly—the oil will smooth itself into a glass-like coating—and allowed to dry for two to three days. The resulting finish is almost completely impervious to water.

Food contact and allergic reactions

As the source of tung oil is a nut, people with nut allergies often report adverse reactions to contact with (or even the odour of) tung oil. Reactions can be severe in some cases. While tung oil has been used for many centuries as a finish for kitchen items such as wooden bowls and cutting boards, some individuals must avoid its use.

Other uses

As the penetrating power of tung oil is excellent and it will adhere to porous minerals, it is often the “secret” ingredient that traditional stonemasons apply to granite or marble that is destined to serve duty in kitchens, bathrooms and other staining fluid environments. Applied at a 1:5 ratio (oil to naphtha), it seals the surfaces permanently, while also giving a finish like that of wet stone to the product. Often several thin layers are applied at the high solvent-to-oil ratio, in order to build up the durability and permanence of the coating. The non-yellowing nature of tung oil is vitally important for its satisfactory use in these applications. Clean up, especially of hands, may be difficult without a solvent.

References

1. ^ Food and Agriculture Organization of the United Nations. "Minor oil crops - Individual monographs". http://www.fao.org/docrep/X5043E/x5043E0e.htm. Retrieved 2007-10-15. 

External links

• Finishing pine with tung oil
• Oil Finishes: Their History and Use