Car Computers and Sensors
Car Electronics and Lights
Jeep Liberty Sport
Physics
Electrical Engineering

02 jeep liberty O2 sensor circuit slow respones bank 2 sensor 1 check light?

456

Top Answer
User Avatar
Wiki User
Answered
2009-06-26 01:28:06
2009-06-26 01:28:06

Its located in the right exhaust downpipe just before the mini catalytic converter. It referered to as 2/1. John

012
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


O2 sensor circuit malfunction, Bank 1 sensor 2. Check the O2 sensor after the catalytic converter.


Camshaft Position Sensor Circuit Intermittent


Code 41 is an "air temperature sensor" fault. (KA24E Engines only). Check the circuit for "open circuit" or "shorted circuit" first. Change sensor.


O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)


Sure you could get one of these*P0460 Fuel Level Sensor Circuit Malfunction*P0461 Fuel Level Sensor Circuit Range/Performance*P0462 Fuel Level Sensor Circuit Low Input*P0463 Fuel Level Sensor Circuit High Input*P0464 Fuel Level Sensor Circuit Intermittent


PO137 (Sensor Circuit low voltage Bank 1 Sensor 2) This is the O2 sensor behind the Catalytic Converter on the driver's side. Check the wiring on that sensor before proceeding. More than likely replacing that sensor will solve the problem especially if you have over 75,000 miles on the vehicle. But there is no guarantee that will fix it.


P1401 is DPFE sensor circuit high, check out this tutorial to replace the sensor on your Ford


Oxygen sensor circuit open. Check if the wire is plugged in or broken. If it is then replace the O2 sensor.


There are several ways to check your mass airflow sensor. You can measure the output voltage of the sensor, measure the hot film frequency of the sensor, or check the self-cleaning circuit. eHow has a great article that elaborates on these steps.


Trouble code P0150 means:O2 sensor circuit malfunction (bank 2,sensor 1)


Trouble code P0131 means:O2 sensor circuit low voltage (Bank 1 Sensor 1)


Trouble code P0130 means:O2 sensor circuit malfunction (Bank 1 Sensor 1)


O2 sensor circuit bank 1 sensor 2 no activity. Check the wiring and connections to bank 1 sensor 2 O2 sensor, if all looks good replace the sensor.


P0141 is heated oxygen sensor circuit malfunction you need to check the supply voltages to the sensor.


The check engine code PO136 means the O2 sensor circuit malfunction


P0042 HO2S Heater Control Circuit (Bank 1 Sensor 3)


P0520 Code Engine Oil Pressure Sensor/Switch Circuit Malfunction


O2 sensor heater circuit malfunction (bank 1 sensor 1). You probably have a burned out Bank 1 Sensor 1 O2 sensor. Also check the wiring at the sensor for damage.


Camshaft Position Sensor Circuit Malfunction This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it. Symptoms can include: * Hard starting or no start * Rough running / misfiring * Loss of engine power A code P0340 could mean one or more of the following has happened: * a wire or connector in the circuit could be grounded/shorted/broken * the camshaft position sensor may have failed * the PCM may have failed * there exists an open circuit * the crankshaft position sensor may have failed With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try: * Visually inspect all the wiring and connectors in the circuit * Check for continuity in the circuit wiring * Check the operation (voltage) of the camshaft position sensor * Replace the camshaft position sensor as required * Check the crankshaft position circuit as well * Replace circuit wiring and/or connectors as required * Diagnose/replace the PCM as required


O2 sensor circuit slow response. Bank 1 sensor . Suggest you check this out with a OBDII. can be done at Pep Boys.......


Trouble code P0156 means:O2 sensor circuit malfunction (Bank 2 Sensor 2)


IAT sensor 1 circuit high input. Check to see if the Intake Air Temperature Sensor is unplugged.


Coolant temperature sensor circuit high. Check the sensor near where the upper hose attaches to the engine to see if plugged in.


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it. Symptoms can include: * Hard starting or no start * Rough running / misfiring * Loss of engine power A code P0340 could mean one or more of the following has happened: * a wire or connector in the circuit could be grounded/shorted/broken * the camshaft position sensor may have failed * the PCM may have failed * there exists an open circuit * the crankshaft position sensor may have failed With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try: * Visually inspect all the wiring and connectors in the circuit * Check for continuity in the circuit wiring * Check the operation (voltage) of the camshaft position sensor * Replace the camshaft position sensor as required * Check the crankshaft position circuit as well * Replace circuit wiring and/or connectors as required * Diagnose/replace the PCM as required


Trouble code P0387 means:Crankshaft position sensor B circuit low input



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.