answersLogoWhite

0


Best Answer
Copy

This sounds like a classic case of the belt tension being incorrect. The pump is loaded when turning to full lock in either direction and causes the belt to slip when to loose. Adjust the belt and the noise should go away. If it is excessively worn it may pay to replace the belt.

2006-07-18 11:08:06
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

How do you remove crankshaft pulley bolt from a Nissan Pathfinder is it right or left hand thread?

1998 Nissan pathfinder crankshaft pulley bolt is right handed.


How do you know when to replace the pulley on my pathfinder?

what pulley/ there are only about 7 or so on a vehicle. water pump, alternator, ac, power steering pulley


How do you replace a serpentine belt for a 1998 Nissan Pathfinder?

There is either a tensioner or an adjustment screw on a pulley. A Haynes manual or Chiltons manual will help with the routing of the belt, and how to adjust the belt tension as well. Usually the idler pulley is used, before loosening the top bolt , loosen the center bolt of the pulley.


How do you remove a 1998 Nissan Pathfinder crank shaft pulley?

Use a puller. there are two holes on the in side of the pulley. I had to clamp the sides to the pully to the puller, the holes just stripped out. U could drill and re tap the holes to match the bolts on the puller.


I replaced the ac compressor on my 1994 Plymouth grand voyager with a bypass pulley and the belt squeals do you have any ideas why?

Most likely the new pulley is not in line with the rest.


How do you tighten all belts on 92 Nissan pathfinder?

The Alternator and Power Steering Units have a tensioner bolt on each. The final tensioner bolt is just above the tensioner pulley in the top center.


How do you remove a power steering pulley on a 1997 Nissan Altima?

how to remove a power steering pulley on a 1997 Nissan altima


How do you replace the idoler pulley on my Nissan 1996 200sx 1.6?

replace 1996 nissan 200sx se 1.6 tension pulley


What pulley drives alternator belt What is wrong if this pulley isn't turning?

the pulley on the harmonic balance drives the alternator belt. this is the pulley at the bottom of the engine ,on the front of the crank shaft if this pulley is not turning you have a problem. this means either the key is missing or the crankshaft is broken


What causes a pulley to make noise on a 1992 Nissan maxima?

it is time to change bearing on that pulley


2000 Nissan Pathfinder Le for about three months now it has been making a chirping sound from under the hood you have changed the belt and tension pulley it still has a high pitched squealing sound?

You needed a new belt Maybe the pulley that was replaced is the wrong one therefore, the new belt was put on incorrectly.


2005 equinox that squeals from the front end but the squeal comes and goes what could it be?

it could be your pulley that keeps tension on your belt or it could be a belt


How do you remove the steering pump pulley on a Nissan 200sx?

Take off the sockets and remove the pump pulley.


How do you remove a idler pulley from a 97 Nissan pickup?

is it a pintara


What are the Timing Marks on a 1992 Nissan 240SX?

on the dampener pulley


Where are the timing marks for a 1996 Nissan Maxima?

The 1996 Nissan Maxima timing marks can be found on the main pulley, on the front of the engine. The timing marks will be scattered around the outside of the pulley.


What is the angular velocity in radians per second of a pulley turning at 1800 RPM?

The angular velocity of a pulley turning 1800 rpm is 60 pi radians per second.


What simple machine is turning on a sprinkler?

a gear or a pully


How you change idler pulley on 2003 Nissan sentra 1.8?

The idler pulley on a 2003 Nissan Sentra 1.8 is changed by removing the engine accessories, removing the drive belts, and loosening the retaining bolt. The pulley can then be removed from the vehicle and a new one bolted into place.


How to Nissan Frontier belt replacement?

To replace the belt on a Nissan Frontier, first loosen the idler pulley of the belt and remove the bolts. Then slip the replacement belt onto the pulley and put back the bolts.


How do you remove a 2005 Nissan altima auto tensioner pully?

The 2005 Nissan Altima auto tensioner pulley can be removed by removing the center bolt. You will need to hold the pulley stationary while you loosen the bolt.


What is the squealing sound coming from the left side of a 2002 Chevy cavalier it also squeals when running idle?

check the serpentine belt .also check all the pulley wheels especially the belt tensioner.one of the pulley wheel bearings may be badAnswercheck the serpentine belt .also check all the pulley wheels especially the belt tensioner.one of the pulley wheel bearings may be bad


How do you tighten your serpentine belts on a 2001 Nissan Pathfinder?

You don't tighten it. It has an idler pulley that keeps the proper tension. If this is an old belt and is loose, then it needs replacing. If you have installed a new belt and it is loose, then either you installed the wrong belt or the idler spring is weak and the idler needs replacing.


How do you align the crankshaft sprocket to the oil pump housing on a 1990 Nissan Pathfinder when replacing the timing belt?

the mark is a notch in the oil pump housing on the lower right side as you are looking down, and on the crankshaft pulley it is a white mark opposite side of the woodruff key on the face of the pulley. at the topside align the white marks on the belt with the punch marks on the pulleys and the rear timing belt cover.


How do you realign the timing to reinstall the belt properly on a 1991 Nissan Pathfinder with a V6 after the cam and crank shafts moved while removing the timing belt?

every pulley has a mark on it that matches a notch on the inner timing belt/ oil pump cover, line up the white lines on the belt with these marks and that's it.. all 3 marks will line up belt-pulley-case.