answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2009-04-24 22:34:43

Replace the ignition with a MOPAR electronic ignition kit #p3690426. You will never deal with lean burn again. It costs about $200 and bypasses the LBS. ANSWER I'm not sure what the question is. Do you need to identify whether you have the single or dual coil pick-ups? You will have 2 sets of wires coming from under the distributor if you have a dual; and one set if you have single.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still Have Questions?

Related Questions

Where is the distributor cap located on a 2005 Chrysler Sebring?

A 2005 Chrysler Sebring does not have a distributor.


Where is the distributor on a 2008 4 cylinder Chrysler Sebring?

It does not have a distributor.It does not have a distributor.


Where is the distributor cap on a 2003 Chrysler pt cruiser?

It does not have a distributor cap.


Does a 2004 Chrysler 3.3L have a distributor?

No.


Where is the distributor located on a 2001 Chrysler sebring convertible 2.7 limited?

The 2.7L does not have a distributor.The 2.7L does not have a distributor.


What is the firing order and distributor order of a 1993 Chrysler New yorker with a 3.3L V6?

A Chrysler 3.3L does not have a distributor. The firing order is 1,2,3,4,5,6.


Where is distributor cap on 93 Chrysler intrepid?

A 1993 Intrepid does not have a distributor cap.A 1993 Intrepid does not have a distributor cap.


What will happen if the distributor goes out on a 1995 Chrysler cirrus lxi?

The engine will not run with a failed distributor.


How do you change the ignition coil on a chrysler Sebring with the 2.5?

You have to replace the distributor assembly.You have to replace the distributor assembly.


Where is the coil on a V6 2.5 chrysler cirrus located?

It is built into the distributor and is not available without buying a distributor.


Where is the camshaft position sensor on the 1999 Chrysler sebring 2.5L?

It is inside the distributor, serviced as part of the distributor.


Where is the coil wire on my 2000 Chrysler Concorde?

A Chrysler Concorde does not use a distributor, so there is no coil wire.


Where is the camshaft sensor located in a 1995 Chrysler Cirrus 2.5?

It is inside the distributor and is only serviced with a new distributor.It is inside the distributor and is only serviced with a new distributor.


Where is the coil on a 1996 Chrysler Sebring 2.5L?

It is internal to the distributor.


Does a 1983 Chrysler have a rotor in the distributor?

YesYes


Where is the camshaft position sensor on a 1996 Chrysler Cirrus V6 2.5 liter?

It is in the distributor, you have to buy a distributor to replace.


Where is the distributor cap on a 1998 Chrysler van?

The 3.0 is the only engine that has a distributor. It is on the front passenger side of the engine.


2000 Chrysler Sebring has power to distributor but no spark to plugs?

It could be either the crank angle sensor or the distributor module. If it is the distributor module, you have to buy and install a re-man distributor.


Where is cam sensor 1998 Chrysler sebring 2.5?

It a non serviceable part of distributor.It a non serviceable part of distributor.


How much should it cost approxmately to replace a car distributor for a 1996 Chrysler sebring?

The part itself for that distributor $1000.00


Where is the cam sensor for a 2000 Chrysler cirrus 2.5 engine?

It is inside the distributor. You have to replace the distributor to service the cam sensor.


Where is the distributor cap on a 2000 Chrysler Sebring?

2.4L, does not have a distributor. 2.5L, it is on the driver side end of the rear cylinder head.


Where is the camshaft position sensor located on a 1998 Chrysler sebring 2.5l?

it is an part of the distributor unit. you have to change out the entire distributor.


Diagram from the distributor cap to the spark plug on a 2004 chrysler town and country 3.8 L?

A 2004 3.8L does not have a distributor.


Where is the distributor on a 1996 Chrysler Sebring convertible?

The 2.4L does not have a distributor. On the 2.5L, it is on the driver side end of the rear cylinder head.