answersLogoWhite

0


Best Answer

I can tell you its a pain in the rear end. The PCV is located on the rear valve cover. However, they didnt give you enuf room to get to it, or pull it out, or replace it. And if you do get it out, you run a HIGH risk of disconnecting the tube that goes from the PCV valve into the underside of the intake. And then things really become a pain in the rear.

User Avatar

Wiki User

โˆ™ 2007-07-15 03:49:07
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: 1988 Pontiac 6000 v-6 pcv valve location?
Write your answer...
Submit
Related questions

When the 1988 Pontiac 6000 accelerated there is a loud screeching noise from front tiresWhat is it?

its called a burnout


Why won't my 1985 Pontiac 6000 start?

have a pontiac 6000 2.5 motor and it wont stay running


Where is location of PCV valve on sierra c3 vortec 6000?

top right og head covers.


Where is the oil filter located on an 1988 Pontiac 6000?

On the oil pan there is a cap you unscrew, and inside there is a "card board filter", that you would pull out and replace.


Where is the PCV valve on a 1986 Pontiac 6000 STE?

to the Owner of the 1986 STE: I own two 1985's STE's and I noticec the PCV valve is on the front valve cover. I hope this will be of some help. Most Sincerely, Kristopher Gerbracht www.kristopher.gerbracht@juno.com


Where can find a picture of the serpentine belt layout for a 1988 Pontiac 6000?

You might try the autozone website or the Pontiac partsman as he might be able to print it out for you, should be a picture of it under the hood of the car or in your owners manual if you still have it.


Where is the ignition module on a 1985 Pontiac 6000?

On the distributor.


Where is the oil filter on a 1990 Pontiac 6000?

The oil filter on a 1990 Pontiac 6000 is located on the driver's side of the engine compartment. It is on the side of the motor all the way to the rear, near the firewall.


Where is the pcv valve located on a 1989 Pontiac 6000 2.8 engine?

there is hose running from the top of the engine to the air intake. your pcv valve is located on the engine side of that hose. Mostly correct except there is no PCV valve; there's just a straight pipe going from the valve cover to the air plenum intake hose. Hope this helps. RJK75


Will the springs and struts from a 1989 Pontiac 6000 le wagon fit onto a 1989 Pontiac 6000 le sedan?

You could call your local auto parts store and they should know the answer to that one


Where is the fuel pump located on a 1985 Pontiac 6000?

Fuel tank


What is the gap on the spark plugs for a 1991 Pontiac 6000 le?

.060"


Where can one find reviews for the Pontiac 6000 car?

There appears to be a large amount of information available for the Pontiac 6000 car. If one is wanting to view reviews these can be found on the Edmunds site as well as on Car Guru.


Where can you find a wiring diagram for a 1985 Pontiac 6000?

Wiring diagram of what component?


Diagram of Pontiac 6000 motor?

2.5L 4cyl base. Iron Duke


Where is the pepcock located on a 1990 Pontiac 6000 v6?

Should be at the bottom or rear of radiator


Weight of 87 Pontiac 6000 se?

The weight of the Pontiac 6000 SE is recorded as being 3,021 pounds. This weight can be altered by aftermarket products which are installed on the vehicle or parts which may have been taken off of the vehicle since being manufactured.


Where is th low side ac port on a Pontiac 6000 3.1l?

The Pontiac 6000 low side air-conditioner import can be found on top of the air conditioning compressor. The low side air-conditioner port will be labeled as the low pressure port.


Where is the oil sensor on a Pontiac 1989 6000 LE with a 2.8 V6?

It is next to the oil filter.


Why does my Pontiac 6000 have a high idle?

A sticking choke or vacuum leak are two common causes.


How much does a 1988 24ft sea ray sierra weigh?

6000


What is the firing order for a 1986 Pontiac SE 6000 2.8 liter?

To The Owne of the 1986 6000 SE: The firing order is 1,2,3,4,5,6. Most Sincerely, Kristopher Gerbracht www.kristopher.gerbracht@juno.com


What is measurements for installing new outer tie-rods on Pontiac 6000 fwd?

The replacement of outer tie rod ends onto a Pontiac 6000 does not require "measurements." However, the vehicle will need to an alignment after install. An alignment usually takes initial measurements of the wheel geometries, and the technician uses these to adjust the wheels back into specification. For the 1991 Pontiac 6000, the final year of production, the AC Delco Professional outer tie rod is part number 45A0230.


What does the model of Pontiac 600 LE look like?

http://www.carsurvey.org/images/pontiac_6000_1.jpg If you mean Pontiac 6000, not 600, which is an old Dodge model, then this is a picture of one.


How do you get the key out of the stuck ignition switch of a 1988 Pontiac 6000?

You cant. You have to replace the key lock. Can be a slightly involved process. You have to take the steering wheel off, lock spring, and other things to get to it. I recomend on this repair going to a repair shop. This is what I did, and I am glad I did.