answersLogoWhite

0


Best Answer

I had recently experienced this with my 1989 626. The pedal only stuck to floor in 1st and reverse gears at first then eventually stayed stuck. I replace the clutch master cylinder. It could also be the slave cylinder which is where you will find the bleeder valve. Follow the hydraulic line from the master down to the slave and you will find the bleeder valve. First thing that i looked at was the fluid level in the reservour, then the master cylinder than the slave. Good luck

User Avatar

Wiki User

โˆ™ 2006-03-10 02:05:57
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: 1991 Mazda 626GT's clutch pedal has sunk to the floor Think there is air in the system Need to find bleeder valve to bleed air out?
Write your answer...
Submit
Related questions

How do you bleed the clutch on a 1993 Mazda B2200?

follow the line from the master cylinder for the clutch usually there is a bleeder screw on the fire wall a couple feet from cyclinder, get some one to pump the clutch as you would bleeding the brakes, then theres a nother bleeder screw b4 the line goes to the flexline by the trans


How do you change clutch oil on a Mazda sting?

unless your Mazda has a wet clutch , as motorcycles do, you don't have clutch oil


How do you adjust the clutch on 1993 Mazda MX6?

YOu need to blead the system .. then it should require no adjusting


How Where do you add Clutch Fluid on a 1997 Mazda B2300 Manual?

where do you add clutch fluid on a Mazda 1997


How do you bleed brakes on a 2005 Mazda 3?

With the bleeder screws


Where is the clutch master cylinder on 2007 Mazda 3?

how do you bleed the clutch master cylinder in a 2005 mazda 3


How do you Bleed the Clutch Slave Cylinder on a 1993 Mazda 626?

The clutch in a car equipped with a manual transmission system can sometimes stop working properly. The clutch pedal may weaken and not engage or disengage properly, much like the brake pedal in a car. When this happens, it is necessary to bleed the clutch slave cylinder; this will tighten the clutch pedal and ensure proper performance. It is helpful to ask a second person to help you bleed the clutch, as one person will need to depress the clutch pedal while the other person works in the engine bay area. 1. Step 1 Locate the clutch release cylinder under the hood of the car. Pull off the rubber cap from the bleeder screw. 2. Step 2 Attach the bleeder tube over the end of the bleeder screw. Push the tube in to secure it tightly and to guarantee a vacuum seal. 3. Step 3 Fill the jar halfway with hydraulic brake fluid. Place the free end of the bleeder tube into the brake fluid. 4. Step 4 Press the clutch pedal to the floor and release it slowly to the original position. Repeat this process several times. 5. Step 5 Hold the clutch pedal to the floor; at the same time, use a line wrench to loosen the bleeder screw until the brake fluid begins to run out into the jar, then close the clutch cylinder bleeder screw. Repeat this step several times while watching the fluid in the jar for air bubbles. (This step works best with the help of your assistant, who can watch out for the air bubbles while you press on the clutch.) 6. Step 6 Close the bleeder screw when the air bubbles have stopped forming in the jar. 7. Step 7 Reattach the rubber cap to the tip of the bleeder screw.


Is the Mazda 121 clutch hydraulic?

No


How do you check clutch cable on your 1990 Mazda 323?

caint it has a hydraulic clutch


How long does a clutch last on Mazda Protege?

I had to change the clutch at 120,000 kilometers.


How do you adjust clutch on 1995 Mazda Protege LX which has to be pushed all the way in and shifted carefully and hydraulic cylinder cannot be located under hood for adding fluid?

your brake master cylinder serves as your slave cylinder resevior. If either your master or slave clutch cylinders are going bad, it may not do any good to try to adjust them. But the slave cylinder has a bleeder screw and the process of bleeding the clutch is similar to bleeding the brakes. In short, open the bleeder screw when clutch is being pressed, and close it when clutch is fully pressed. Have a tube on the bleeder screw going into a jar of brake fluid so you can see bubbles coming out of the slave. The slave is mounted on the bottom of the transmission and the master clutch cylinder is on the firewall behind and below the battery, it has a tube that goes to the lower right rear of the master brake cylinder reservoir to get it's fluid supply.


Where is the clutch fluid after leaking on a 1986 Mazda B2000?

Normally if the clutch fluid reservoir is low the slave cylinder is leaking at the transmission on the right hand side.Check the fluid level then check the slave and if it's leaking it will be there and typical visual is cracked rubber boot coated in brake fluid.Result to fix replave this part and bleed it as you would brakes,there is a bleeder screw on the slave cyldr and have another person pump the clutch pedal to remove excess air out of system.


How do you fix a 1981 Mazda 323 clutch?

unbolt tranny from engine clutch is between them


Is there a hydraulic clutch on a 1992 Mazda Miata?

Yes, all miata's have a hydraulic clutch.


Is there clutch adjustment on a Mazda 1991 929?

It is important to know as much as possible about the car that it is driven. Yes, there is a clutch adjustment on a 1991 Mazda 929.?æ


How do you remove the radiator fan clutch on 1994 Mazda B-4000 truck?

how do you remove the fan clutch on a 1994 mazda b 4000 4.0


Where is the reserve tank for the clutch fuel in 99 mazada 626?

I'm not positive about the '99 model year, but the hydraulic clutch shares the fluid reservoir with the brake system in earlier Mazda models.


Mazda b3000 clutch working in upper gears but not to lower gears or reverse?

get a new clutch


Does a Mazda B2600i have anykind of hydraulic system in the clutch?

The 89-93 B2600i clutch is hydraulically operated. The clutch pedal is linked to a clutch master cylinder via an adjustable rod, the clutch slave is bolted to the outside of the transmission allowing it to be replaced without removing the transmission and uses a fork to actuate the clutch. See the links below for additional information.


If the clutch is constantly slipping in a 1986 Mazda 626 DX where and how do you add clutch fluid?

you dont add clutch fluid. If the clutch is slipping that means that you need to buy a new clutch


How do you adjust the clutch on a 1988 Mazda B2200 with a 5 speed?

At the top of the clutch pedal in the cab of the truck.


Where and do you add clutch oil to a 92 Mazda Protege?

there isn't clutch oil only transmission and engine oil


How do you repair a clutch in your Mazda 1991 pu b2600i?

See if your public library has a Chilton's for your car to replace the clutch.


Is the 1996 Mazda B3000 hydraulic clutch self adjusting?

No this clutch needs to be bench bled prior to instalation.


Where do you fill the clutch fluid on a Mazda T3500 truck?

You don't use clutch fluid for a manual transmission vehicle.