1995 jaguar xjs v12 check engine codes FF 37 and FF 44?

www.troublecodes.net Good luck I have a 1995 jdauksz1@charter.net

Click the link for directions and a diagram.

http://www.obd-codes.com/

Check the codes with an OBD2 scan tool.

After 1995, an OBDII scanner is necesary to read the engine codes. If you do not have access to a scanner, you can take your vehicle to AutoZone and they will scan ffree of charge.

All 1995 and later model vehicles require an OBDII scanner tool to retrieve the trouble codes.

There are pages and pages of causes for the check angine light. Have it checked fro codes with a scan tool.

If your check engine light is staying on with the engine running , a malfunction has been detected with the emission control system . Have your Explorer scanned for any trouble codes to diagnose and repair the problem

1995 and later model vehicles need an OBDII scanner to retrieve the diagnostic codes. AutoZone and other parts stores usually will scan free of charge if the check engine light is on.

You read the codes with a scanner, repair the cause, and clear the code with the scanner.

JAGUAR vehicles obd1 code retrieval For Jaguar vehicles with obd1 codes (made before 1995 or 1993), testing the check engine lights in your dash to get the code is simple. All you do is locate the Vehicle Condition Monitor (VCM) button in the dash panel sitting below the tachometer and speedometer. The procedure begins by turning the key off and waiting for 5 seconds then turning the ignition key to position 2 without starting the engine. When you press the VCM button, codes will start to display in your dash panel. Clearing the codes can be done by turning the key off and removing the battery negative terminal for 30 seconds and reconnect. http://www.extreme-check-engine-light-codes.com/Jaguar%20OBD1%20Decoder.htm

This could mean many things that need to be looked at. Get a scan reading and it will give the codes as to what the check light is on for.

There are pages and pages and items that can cause a check engine light. You need to have it checked for codes with a scan tool. After repair light can be shut off with scan tool.

There are pages and pages and items that can cause a check engine light. You need to have it checked for codes with a scan tool. After repair light can be shut off with scan tool.

If the check engine light is on then have it scanned for codes. I could guess you into bankruptsy. It is cheaper to have it scanned and repaired.

What is the Question? Where is the CEL? How do you read the codes? Your Answer is HERE; http://www.brickboard.com/FAQ/700-900/

1995 and later Mazda B-Series Pick-ups incorporate the OBDII diagnostic system and you will need a scanner to retrieve the trouble codes. Some auto parts stores will scan free if the check engine light is on.

End of message, no more codes.

On this vehicle the check engine light must be reset with a scan tool.

You can't manually get the check engine light to give you the trouble codes on your vehicle. 1995 and later vehicles use the OBDII system and you must use a scanner tool to retrieve the codes. You can go to AutoZone or similar auto parts store that offers free scans to get the trouble codes retrieved. Or you can buy your own scan tool for about $70.

Hi, Check the decal pasted under the hood. I have a 1995 G20 and it is OBD II. Those cost a lot more than the I.

The powertrain control module has detected a malfunction Take it in and have it scanned for trouble codes in order to have the problem repaired (Helpfull)

use an OBD-I code reader.

TAke it to the dealer. They have check out charts for times when the computer doesn't set codes.

what year????????????? Check engine light diagnosis depends on the model year of your vehicle. 1995 and later models have the OBDII system and require a scan tool to retrieve the trouble codes. For 1994 and earlier models, you can check out a manual (Haynes or Cilton) at your local library and read how to manually retrieve the codes - also what each code refers to.