answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2006-11-21 14:24:35

should be 20mV at output while cranking

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

If you replaced the camshaft position sensor should you replace the crankshaft position?

I changed only the camshaft position sensor on my 2000 Kia Sportage. So I don't think so.


Where is the crankshaft position sensor on a 2002 Saturn SL1?

the crank sensor is on the back of the engine above/behind the starter Two wires green connector I'm not sure of the exact position, but I had one changed on a 98 SL2 and they put the car on a rack to access it, sugesting it being underneath the crankshaft. Hope this helps.


What to do if your svchost.exe has changed?

The sound options on your computer may malfunction.


Where is the crankshaft position sensor located on a 99 dodge stratus 2.4 4cyl?

It is on the backside of the block close to the oil filter. I just changed mine 2 days ago.


1998 Pontiac sunfire will not start it does not get a spark and i changed the ignition coils and the module below it please help me get it started thanks?

Have you checked for a computer code? That vehicle should have either a crankshaft position sensor or a camshaft position sensor. Make sure it is working properly.


When the car turned the corner its what changed?

position changed


You have a2001 Mazda 626 that the alternator belt broke on changed the belt as well as the spark plugs and wires but now the car won't start the battery turns over but it doesn't start help?

Check your Crankshaft position sensor. Located on the right of the crankshaft. Probably got damaged when belt broke.


Changed crankshaft sensor and camshaft sensor now it won t start?

changed camshaft and crankshaft sensors in 2005 toyota tacoma 6 clyinder and now it wont start any idea what to try next


Why would check engine light stay on after crankshaft sensor is changed when code said crankshaft sensor is bad?

Check to see if the wiring is damaged.


Do 2004 Hyundai Santa fe 2.7 has a crankshaft sensor?

yes it does, I had mine changed this year.


My 1997 Ford Escort ran yesterday and I changed the serpentine belt tensioner and the serpentine belt and the alternator and the car cranks and sparks and has gas so why won't my car start now?

Check that the CKP Crankshaft position sender wasn't knocked out of alignment when you put on the belt. It is at the 10 o'clock position.


1992 buick lesabre runs fine you shut it off then 30 mins later it stalls a half mile down the road maf cps vss sensors all changed?

we had the same problem. we changed the Crankshaft Position sensor, and also the camshaft position sensor. changed ignition coils, and the module under the ignition coil, and still had the stalling problem. an auto mechanic bought it from us and he discovered all that it was was a pinched wire under the ignition module.


What changes when you can tell that an object has been moved?

Time has changed. The object has changed its position. Your view has changed.


What size is the bolt head on the crankshaft on a 1997 Metro 1.3 4-cylinder and what is involved in changing the crankshaft seal?

On my "99" it is 17 MM. I've never changed a seal.


Will the crankshaft and heads from a 1973 Chevy fit a 1990 block?

Chevy in 1977 changed the rear main oil seal to a one piece seal. the older crankshaft wont work.


How do you fix your esp malfunction on mercedes benz E350?

The ESP malfunction, on a Mercedes Benz E3 50, can only be fixed by changing the computer motherboard. The computer motherboard should only be changed by a certified mechanic.


Have a 94 mirage 1.5 no fire to the plugs changed the electronic ignition how do you check the crankshaft sensor and where is it located?

The crankshaft sensor in your 1990 former Roche is located on the front of the engine. The best way to test your crankshaft sensor is to hook the engine to a Dyno tester.


How often should crankshaft sensor be changed?

Only when it goes bad, in most cases it will not go bad.


How did the safety pin change lives?

the safety pin changed lives by helping people with their wardrobe malfunction. they also used safety pins for diapers and as a fasion statement. the safety pin changed lives by helping people with their wardrobe malfunction. they also used safety pins for diapers and as a fasion statement.


Is a square that has changed position called a rhombus?

No


How are speed and position related?

position and speed both occur when something is moved or changed from it's original position.


1996 gmc jimmy it turns over but will not start ive changed the spark plugs distributor cap ignition coil and fuel pump what causes it not to start?

Your Jimmy has a crankshaft position sensor mounted by your crankshaft pully in the front of your engine on the bottom. If the senor is bad your engine does not recognize that your engine is turning and will not fire the plugs. Try changing your sensor and your engine should start.


Can a Monster who was switched fom attack position to defense position by a card's effect be switched back by the owner?

It depends.If the Monster declares an attack or already attacked and it is switched to defense position by a card effect (like Enemy Controller or Book of Moon for example) the Monster's position cannot be changed by you, the controller, because it declared an attack already. A Monster's position cannot be changed by their controller for the rest of a turn after they declared attacked with it.If the Monster did not attack yet this turn and their position is changed due to a card effect, it can be changed by the controller.


What is a rotary rheostat?

A variable resistor having only two terminals whose resistance value is changed by rotating a shaft or screw.


How do you adjust cam timing on a 5.0 mustang?

for pre-95 Mustang 5.0 Camshaft Timing is changed by moving the camshaft in relation to the crankshaft. By advancing the camshaft the valves open and close earlier in relation to the position on the crankshaft. By retarding the camshaft the valves open and close later in relation to the position of the crankshaft. A degree wheel as well as other tools are needed for this procedure. Some aftermarket timing gears have extra keyways cut into the crankshaft gear to provide alternative adjustments for advancing or retarding the camshaft. Offset bushings or adjusting keyways are also sold to adjust the timing by a few degrees to account for manufacturing inaccuracies. The bottom line is if you do not know what you are doing, this is one of the areas that you can do a lot of damage to your engine. Tread carefully.